GY-63_MS5611/libraries/DS18B20_INT/README.md
2022-06-24 17:29:55 +02:00

4.4 KiB

Arduino CI Arduino-lint JSON check License: MIT GitHub release

DS18B20_INT

Minimalistic library for the DS18B20 temperature sensor - restricted to one sensor per pin.

Arduino Temperature Control Library (ATCL)

This DS18B20 library is a minimalistic library for a DS18B20 sensor. It will give only temperatures in whole degrees C. Goal is to minimize footprint.

If you need more functions or control over the DS18B20 family I refer to the library of Miles Burton - https://github.com/milesburton/Arduino-Temperature-Control-Library

I'm a great fan of the above library however some time ago I needed to strip it down to save a few dozen bytes. I reworked that minimalistic version into a library and I added a number of Arduino examples to help you get started.

This library is also related to - https://github.com/RobTillaart/DS18B20_RT

Interface

This DS18B20_INT library supports only the DS18B20, only one sensor per pin, no parasite mode, no Fahrenheit and no alarm functions. The only feature the class supports is the asynchronous reading of the temperature by means of three core functions:

  • *DS18B20_INT(OneWire ) constructor needs a reference to OneWire object.
  • bool begin(uint8_t retries = 3) resets oneWire and set resolution to 9 bit.
    returns true if all is OK. there will be a number of retries to connect, default 3.
  • void requestTemperatures() trigger temperature conversion.
  • bool isConversionComplete() check if conversion is complete.
  • int16_t getTempC() returns temperature in whole degrees only. -55..125
    or -127 = DEVICE_DISCONNECTED
  • bool getAddress() returns true if the sensor is configured (available).

CentiC part

The following functions are experimental since 0.2.0 They allow to use a higher resolution while not using floats. This keeps the library small.

  • void setResolution(uint8_t bits = 9) sets the internal resolution to 9, 10, 11 or 12 bits. Other numbers will be mapped on 9. This will affect the conversion time for a measurement. Internally it will call begin() to set the new resolution if needed.
  • void getResolution() returns the bits set, default 9. Convenience function.
  • getTempCentiC(void) returns the measured temperature times 100. -5500..12500 So 10.62°C will be returned as 1062.

Warning The DEVICE_DISCONNECTED is not tested for, but is commented in the code. Use at own risk.

Operation

This library supports only one DS18B20 per Arduino/ MCU pin.

    //  BOTTOM VIEW
    //
    //          PIN  MEANING
    //   /---+
    //  /  o |  1    GND
    //  |  o |  2    DATA
    //  \  o |  3    VCC
    //   \---+

Connect a pull-up resistor 4.7 KOhm between pin3 and pin2. When the wires are longer this resistor needs to be smaller.

Pull up resistor

An indicative table for pull up resistors, (E12 series), to get started.

Note: thicker wires require smaller resistors (typically 1 step in E12 series)

Length - 5.0 Volt - 3.3 Volt
10cm (4") 10K0 6K8
20cm (8") 8K2 4K7
50cm (20") 4K7 3K3
100cm (3'4") 3K3 2K2
200cm (6'8") 2K2 1K0
500cm (16'8") 1K0 *
longer * *

* = no info, smaller

Credits

Miles Burton who originally developed the Arduino Temperature Control Library. and all people who contributed to that lib.

Future

  • add examples
    • a multi sensor == multiple pins, no bus
  • add rounding for getTempC().
    • now it truncates, so it can be 0.5°C off.
    • add "0.5" to raw and truncate