mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
07a506bb02
The RTC I2C peripheral always expects a I2C slave sub register address to be programmed. If it is not programmed then a sub register address available in SENS_SAR_I2C_CTRL_REG[18:11] is used for I2C read/write. This commit updates the documentation of the API ulp_riscv_i2c_master_set_slave_reg_addr() to clarify the same.
104 lines
3.6 KiB
C
104 lines
3.6 KiB
C
/*
|
|
* SPDX-FileCopyrightText: 2022 Espressif Systems (Shanghai) CO LTD
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
#pragma once
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
#include <stdint.h>
|
|
#include <stdbool.h>
|
|
#include "hal/gpio_types.h"
|
|
#include "esp_err.h"
|
|
|
|
typedef struct {
|
|
uint32_t sda_io_num; // GPIO pin for SDA signal. Only GPIO#1 or GPIO#3 can be used as the SDA pin.
|
|
uint32_t scl_io_num; // GPIO pin for SCL signal. Only GPIO#0 or GPIO#2 can be used as the SCL pin.
|
|
bool sda_pullup_en; // SDA line enable internal pullup. Can be configured if external pullup is not used.
|
|
bool scl_pullup_en; // SCL line enable internal pullup. Can be configured if external pullup is not used.
|
|
} ulp_riscv_i2c_pin_cfg_t;
|
|
|
|
typedef struct {
|
|
uint32_t scl_low_period; // SCL low period
|
|
uint32_t scl_high_period; // SCL high period
|
|
uint32_t sda_duty_period; // Period between the SDA switch and the falling edge of SCL
|
|
uint32_t scl_start_period; // Waiting time after the START condition
|
|
uint32_t scl_stop_period; // Waiting time before the END condition
|
|
uint32_t i2c_trans_timeout; // I2C transaction timeout
|
|
} ulp_riscv_i2c_timing_cfg_t;
|
|
|
|
typedef struct {
|
|
ulp_riscv_i2c_pin_cfg_t i2c_pin_cfg; // RTC I2C pin configuration
|
|
ulp_riscv_i2c_timing_cfg_t i2c_timing_cfg; // RTC I2C timing configuration
|
|
} ulp_riscv_i2c_cfg_t;
|
|
|
|
/* Nominal default GPIO settings and timing parametes */
|
|
#define ULP_RISCV_I2C_DEFAULT_CONFIG() \
|
|
{ \
|
|
.i2c_pin_cfg.sda_io_num = GPIO_NUM_3, \
|
|
.i2c_pin_cfg.scl_io_num = GPIO_NUM_2, \
|
|
.i2c_pin_cfg.sda_pullup_en = true, \
|
|
.i2c_pin_cfg.scl_pullup_en = true, \
|
|
.i2c_timing_cfg.scl_low_period = 5, \
|
|
.i2c_timing_cfg.scl_high_period = 5, \
|
|
.i2c_timing_cfg.sda_duty_period = 2, \
|
|
.i2c_timing_cfg.scl_start_period = 3, \
|
|
.i2c_timing_cfg.scl_stop_period = 6, \
|
|
.i2c_timing_cfg.i2c_trans_timeout = 20, \
|
|
}
|
|
|
|
/**
|
|
* @brief Set the I2C slave device address
|
|
*
|
|
* @param slave_addr I2C slave address (7 bit)
|
|
*/
|
|
void ulp_riscv_i2c_master_set_slave_addr(uint8_t slave_addr);
|
|
|
|
/**
|
|
* @brief Set the I2C slave device sub register address
|
|
*
|
|
* @note The RTC I2C peripheral always expects a slave sub register address to be programmed. If it is not, the I2C
|
|
* peripheral uses the SENS_SAR_I2C_CTRL_REG[18:11] as the sub register address for the subsequent read or write
|
|
* operation.
|
|
*
|
|
* @param slave_reg_addr I2C slave sub register address
|
|
*/
|
|
void ulp_riscv_i2c_master_set_slave_reg_addr(uint8_t slave_reg_addr);
|
|
|
|
/**
|
|
* @brief Read from I2C slave device
|
|
*
|
|
* @note The I2C slave device address must be configured at least once before invoking this API.
|
|
*
|
|
* @param data_rd Buffer to hold data to be read
|
|
* @param size Size of data to be read in bytes
|
|
*/
|
|
void ulp_riscv_i2c_master_read_from_device(uint8_t *data_rd, size_t size);
|
|
|
|
/**
|
|
* @brief Write to I2C slave device
|
|
*
|
|
* @note The I2C slave device address must be configured at least once before invoking this API.
|
|
*
|
|
* @param data_wr Buffer which holds the data to be written
|
|
* @param size Size of data to be written in bytes
|
|
*/
|
|
void ulp_riscv_i2c_master_write_to_device(uint8_t *data_wr, size_t size);
|
|
|
|
/**
|
|
* @brief Initialize and configure the RTC I2C for use by ULP RISC-V
|
|
* Currently RTC I2C can only be used in master mode
|
|
*
|
|
* @param cfg Configuration parameters
|
|
* @return esp_err_t ESP_OK when successful
|
|
*/
|
|
esp_err_t ulp_riscv_i2c_master_init(const ulp_riscv_i2c_cfg_t *cfg);
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|