esp-idf/docs/en/api-reference/peripherals/i2s.rst
2021-08-04 10:20:03 +08:00

356 lines
13 KiB
ReStructuredText

I2S
===
{IDF_TARGET_I2S_NUM:default="two", esp32s2="one", esp32c3="one"}
Overview
--------
I2S (Inter-IC Sound) is a serial, synchronous communication protocol that is usually used for transmitting audio data between two digital audio devices.
{IDF_TARGET_NAME} contains {IDF_TARGET_I2S_NUM} I2S peripheral(s). These peripherals can be configured to input and output sample data via the I2S driver.
An I2S bus consists of the following lines:
- Master clock line (operational)
- Bit clock line
- Channel select line
- Serial data line
Each I2S controller has the following features that can be configured using the I2S driver:
- Operation as system master or slave
- Capable of acting as transmitter or receiver
- DMA controller that allows for streaming sample data without requiring the CPU to copy each data sample
Each controller can operate in half-duplex communication mode. Thus, the two controllers can be combined to establish full-duplex communication.
.. only:: esp32
I2S0 output can be routed directly to the digital-to-analog converter's (DAC) output channels (GPIO 25 & GPIO 26) to produce direct analog output without involving any external I2S codecs. I2S0 can also be used for transmitting PDM (Pulse-density modulation) signals.
.. only:: esp32 or esp32s2
The I2S peripherals also support LCD mode for communicating data over a parallel bus, as used by some LCD displays and camera modules. LCD mode has the following operational modes:
- LCD master transmitting mode
- Camera slave receiving mode
- ADC/DAC mode
For more information, see *{IDF_TARGET_NAME} Technical Reference Manual* > *I2S Controller (I2S)* > LCD Mode [`PDF <{IDF_TARGET_TRM_EN_URL}#camlcdctrl>`__].
.. only:: SOC_I2S_SUPPORTS_APLL
.. note::
For high accuracy clock applications, use the APLL_CLK clock source, which has the frequency range of 16 ~ 128 MHz. You can enable the APLL_CLK clock source by setting :cpp:member:`i2s_config_t::use_apll` to ``TRUE``.
If :cpp:member:`i2s_config_t::use_apll` = ``TRUE`` and :cpp:member:`i2s_config_t::fixed_mclk` > ``0``, then the master clock output frequency for I2S will be equal to the value of :cpp:member:`i2s_config_t::fixed_mclk`, which means that the mclk frequency is provided by the user, instead of being calculated by the driver.
The clock rate of the word select line, which is called audio left-right clock rate (LRCK) here, is always the divisor of the master clock output frequency and for which the following is always true: 0 < MCLK/LRCK/channels/bits_per_sample < 64.
Functional Overview
-------------------
Installing the Driver
^^^^^^^^^^^^^^^^^^^^^
Install the I2S driver by calling the function :cpp:func`i2s_driver_install` and passing the following arguments:
- Port number
- The structure :cpp:type:`i2s_config_t` with defined communication parameters
- Event queue size and handle
Once :cpp:func`i2s_driver_install` returns ``ESP_OK``, it means I2S has started.
Configuration example:
.. only:: not SOC_I2S_SUPPORTS_TDM
.. code-block:: c
static const int i2s_num = 0; // i2s port number
i2s_config_t i2s_config = {
.mode = I2S_MODE_MASTER | I2S_MODE_TX,
.sample_rate = 44100,
.bits_per_sample = I2S_BITS_PER_SAMPLE_16BIT,
.channel_format = I2S_CHANNEL_FMT_RIGHT_LEFT,
.communication_format = I2S_COMM_FORMAT_STAND_I2S
.tx_desc_auto_clear = false,
.dma_buf_count = 8,
.dma_buf_len = 64,
.use_apll = false,
.intr_alloc_flags = ESP_INTR_FLAG_LEVEL1 // Interrupt level 1, default 0
};
i2s_driver_install(I2S_NUM, &i2s_config, 0, NULL);
.. only:: SOC_I2S_SUPPORTS_TDM
.. code-block:: c
static const int i2s_num = 0; // i2s port number
i2s_config_t i2s_config = {
.mode = I2S_MODE_MASTER | I2S_MODE_TX,
.sample_rate = 44100,
.bits_per_sample = I2S_BITS_PER_SAMPLE_16BIT,
.channel_format = I2S_CHANNEL_FMT_RIGHT_LEFT,
.communication_format = I2S_COMM_FORMAT_STAND_I2S,
.tx_desc_auto_clear = false,
.dma_buf_count = 8,
.dma_buf_len = 64,
.bits_per_chan = I2S_BITS_PER_SAMPLE_16BIT
};
i2s_driver_install(I2S_NUM, &i2s_config, 0, NULL);
Setting Communication Pins
^^^^^^^^^^^^^^^^^^^^^^^^^^
Once the driver is installed, configure physical GPIO pins to which signals will be routed. For this, call the function :cpp:func`i2s_set_pin` and pass the following arguments to it:
- Port number
- The structure :cpp:type:`i2s_pin_config_t` defining the GPIO pin numbers to which the driver should route the MCK, BCK, WS, DATA out, and DATA in signals. If you want to keep a currently allocated pin number for a specific signal, or if this signal is unused, then pass the macro :c:macro:`I2S_PIN_NO_CHANGE`. See the example below.
.. note::
MCK only takes effect in `I2S_MODE_MASTER` mode.
.. code-block:: c
static const i2s_pin_config_t pin_config = {
.mck_io_num = 0,
.bck_io_num = 4,
.ws_io_num = 5,
.data_out_num = 18,
.data_in_num = I2S_PIN_NO_CHANGE
};
i2s_set_pin(i2s_num, &pin_config);
Running I2S Communication
^^^^^^^^^^^^^^^^^^^^^^^^^
To perform a transmission:
- Prepare the data for sending
- Call the function :cpp:func:`i2s_write` and pass the data buffer address and data length to it
The function will write the data to the DMA Tx buffer, and then the data will be transmitted automatically.
.. code-block:: c
i2s_write(I2S_NUM, samples_data, ((bits+8)/16)*SAMPLE_PER_CYCLE*4, &i2s_bytes_write, 100);
To retrieve received data, use the function :cpp:func:`i2s_read`. It will retrieve the data from the DMA Rx buffer, once the data is received by the I2S controller.
.. code-block:: c
i2s_read(I2S_NUM, data_recv, ((bits+8)/16)*SAMPLE_PER_CYCLE*4, &i2s_bytes_read, 100);
You can temporarily stop the I2S driver by calling the function :cpp:func:`i2s_stop`, which will disable the I2S Tx/Rx units until the function :cpp:func:`i2s_start` is called. If the function :cpp:func`i2s_driver_install` is used, the driver will start up automatically eliminating the need to call :cpp:func:`i2s_start`.
Deleting the Driver
^^^^^^^^^^^^^^^^^^^
If the established communication is no longer required, the driver can be removed to free allocated resources by calling :cpp:func:`i2s_driver_uninstall`.
Application Example
-------------------
A code example for the I2S driver can be found in the directory :example:`peripherals/i2s`.
.. only:: SOC_I2S_SUPPORTS_ADC_DAC
In addition, there are two short configuration examples for the I2S driver.
.. only:: not SOC_I2S_SUPPORTS_ADC_DAC
In addition, there is a short configuration examples for the I2S driver.
I2S configuration
^^^^^^^^^^^^^^^^^
Example for general usage.
.. only:: not SOC_I2S_SUPPORTS_TDM
.. code-block:: c
#include "driver/i2s.h"
static const int i2s_num = 0; // i2s port number
i2s_config_t i2s_config = {
.mode = I2S_MODE_MASTER | I2S_MODE_TX,
.sample_rate = 44100,
.bits_per_sample = I2S_BITS_PER_SAMPLE_16BIT,
.channel_format = I2S_CHANNEL_FMT_RIGHT_LEFT,
.communication_format = I2S_COMM_FORMAT_STAND_I2S
.tx_desc_auto_clear = false,
.dma_buf_count = 8,
.dma_buf_len = 64,
.use_apll = false,
.intr_alloc_flags = ESP_INTR_FLAG_LEVEL1 // Interrupt level 1, default 0
};
static const i2s_pin_config_t pin_config = {
.bck_io_num = 4,
.ws_io_num = 5,
.data_out_num = 18,
.data_in_num = I2S_PIN_NO_CHANGE
};
i2s_driver_install(i2s_num, &i2s_config, 0, NULL); //install and start i2s driver
i2s_set_pin(i2s_num, &pin_config);
...
/* You can reset parameters by calling 'i2s_set_clk'
*
* The low 16 bits are the valid data bits in one chan and the high 16 bits are
* the total bits in one chan. If high 16 bits is smaller than low 16 bits, it will
* be set to a same value as low 16 bits.
*/
uint32_t bits_cfg = (I2S_BITS_PER_CHAN_32BIT << 16) | I2S_BITS_PER_SAMPLE_16BIT;
i2s_set_clk(i2s_num, 22050, bits_cfg, I2S_CHANNEL_STEREO);
...
i2s_driver_uninstall(i2s_num); //stop & destroy i2s driver
.. only:: SOC_I2S_SUPPORTS_TDM
.. code-block:: c
#include "driver/i2s.h"
static const int i2s_num = 0; // i2s port number
i2s_config_t i2s_config = {
.mode = I2S_MODE_MASTER | I2S_MODE_TX,
.sample_rate = 44100,
.bits_per_sample = I2S_BITS_PER_SAMPLE_16BIT,
.channel_format = I2S_CHANNEL_FMT_RIGHT_LEFT,
.communication_format = I2S_COMM_FORMAT_STAND_I2S
.tx_desc_auto_clear = false,
.dma_buf_count = 8,
.dma_buf_len = 64
};
static const i2s_pin_config_t pin_config = {
.bck_io_num = 4,
.ws_io_num = 5,
.data_out_num = 18,
.data_in_num = I2S_PIN_NO_CHANGE
};
i2s_driver_install(i2s_num, &i2s_config, 0, NULL); //install and start i2s driver
i2s_set_pin(i2s_num, &pin_config);
...
/* You can reset parameters by calling 'i2s_set_clk'
*
* The low 16 bits are the valid data bits in one chan and the high 16 bits are
* the total bits in one chan. If high 16 bits is smaller than low 16 bits, it will
* be set to a same value as low 16 bits.
*/
uint32_t bits_cfg = (I2S_BITS_PER_CHAN_32BIT << 16) | I2S_BITS_PER_SAMPLE_16BIT;
i2s_set_clk(i2s_num, 22050, bits_cfg, I2S_CHANNEL_STEREO);
...
i2s_driver_uninstall(i2s_num); //stop & destroy i2s driver
I2S on {IDF_TARGET_NAME} support TDM mode, up to 16 channels are available in TDM mode. If you want to use TDM mode, set field ``channel_format`` of :cpp:type:`i2s_config_t` to ``I2S_CHANNEL_FMT_MULTIPLE``. Then enable the channels by setting ``chan_mask`` using masks in :cpp:type:`i2s_channel_t`, the number of active channels and total channels will be calculate automatically. Also you can set a particular total channel number for it, but it shouldn't be smaller than the largest channel you use.
If active channels are discrete, the inactive channels within total channels will be filled by a constant automatically. But if ``skip_msk`` is enabled, these inactive channels will be skiped.
.. code-block:: c
#include "driver/i2s.h"
static const int i2s_num = 0; // i2s port number
i2s_config_t i2s_config = {
.mode = I2S_MODE_MASTER | I2S_MODE_TX,
.sample_rate = 44100,
.bits_per_sample = I2S_BITS_PER_SAMPLE_16BIT,
.channel_format = I2S_CHANNEL_FMT_MULTIPLE,
.communication_format = I2S_COMM_FORMAT_STAND_I2S
.tx_desc_auto_clear = false,
.dma_buf_count = 8,
.dma_buf_len = 64,
.chan_mask = I2S_TDM_ACTIVE_CH0 | I2S_TDM_ACTIVE_CH2
};
static const i2s_pin_config_t pin_config = {
.bck_io_num = 4,
.ws_io_num = 5,
.data_out_num = 18,
.data_in_num = I2S_PIN_NO_CHANGE
};
i2s_driver_install(i2s_num, &i2s_config, 0, NULL); //install and start i2s driver
i2s_set_pin(i2s_num, &pin_config);
...
/* You can reset parameters by calling 'i2s_set_clk'
*
* The low 16 bits are the valid data bits in one chan and the high 16 bits are
* the total bits in one chan. If high 16 bits is smaller than low 16 bits, it will
* be set to a same value as low 16 bits.
*/
uint32_t bits_cfg = (I2S_BITS_PER_CHAN_32BIT << 16) | I2S_BITS_PER_SAMPLE_16BIT;
i2s_set_clk(i2s_port_t i2s_num, 22050, bits_cfg, I2S_TDM_ACTIVE_CH0 | I2S_TDM_ACTIVE_CH1); // set clock
...
i2s_driver_uninstall(i2s_num); //stop & destroy i2s driver
.. only:: SOC_I2S_SUPPORTS_ADC_DAC
Configuring I2S to use internal DAC for analog output
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
.. code-block:: c
#include "driver/i2s.h"
#include "freertos/queue.h"
static const int i2s_num = 0; // i2s port number
static const i2s_config_t i2s_config = {
.mode = I2S_MODE_MASTER | I2S_MODE_TX | I2S_MODE_DAC_BUILT_IN,
.sample_rate = 44100,
.bits_per_sample = 16, /* the DAC module will only take the 8bits from MSB */
.channel_format = I2S_CHANNEL_FMT_RIGHT_LEFT,
.intr_alloc_flags = 0, // default interrupt priority
.dma_buf_count = 8,
.dma_buf_len = 64,
.use_apll = false
};
...
i2s_driver_install(i2s_num, &i2s_config, 0, NULL); //install and start i2s driver
i2s_set_pin(i2s_num, NULL); //for internal DAC, this will enable both of the internal channels
//You can call i2s_set_dac_mode to set built-in DAC output mode.
//i2s_set_dac_mode(I2S_DAC_CHANNEL_BOTH_EN);
i2s_set_sample_rates(i2s_num, 22050); //set sample rates
i2s_driver_uninstall(i2s_num); //stop & destroy i2s driver
API Reference
-------------
.. include-build-file:: inc/i2s.inc
.. include-build-file:: inc/i2s_types.inc