mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
110 lines
4.7 KiB
C
110 lines
4.7 KiB
C
// Copyright 2015-2017 Espressif Systems (Shanghai) PTE LTD
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
//
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
#pragma once
|
|
|
|
#include <stdint.h>
|
|
#include <stddef.h>
|
|
#include "esp_err.h"
|
|
#include "freertos/FreeRTOS.h"
|
|
#include "freertos/queue.h"
|
|
|
|
|
|
/// Control tokens used to frame data transfers
|
|
/// (see section 7.3.3 of SD simplified spec)
|
|
|
|
/// Token sent before single/multi block reads and single block writes
|
|
#define TOKEN_BLOCK_START 0b11111110
|
|
/// Token sent before multi block writes
|
|
#define TOKEN_BLOCK_START_WRITE_MULTI 0b11111100
|
|
/// Token used to stop multi block write (for reads, CMD12 is used instead)
|
|
#define TOKEN_BLOCK_STOP_WRITE_MULTI 0b11111101
|
|
|
|
/// Data response tokens
|
|
|
|
/// Mask (high 3 bits are undefined for data response tokens)
|
|
#define TOKEN_RSP_MASK 0b11111
|
|
/// Data accepted
|
|
#define TOKEN_RSP_OK 0b00101
|
|
/// Data rejected due to CRC error
|
|
#define TOKEN_RSP_CRC_ERR 0b01011
|
|
/// Data rejected due to write error
|
|
#define TOKEN_RSP_WRITE_ERR 0b01101
|
|
|
|
|
|
/// Data error tokens have format 0b0000xyzw where xyzw are signle bit flags.
|
|
/// MASK and VAL are used to check if a token is an error token
|
|
#define TOKEN_ERR_MASK 0b11110000
|
|
#define TOKEN_ERR_VAL 0b00000000
|
|
|
|
/// Argument is out of range
|
|
#define TOKEN_ERR_RANGE BIT(3)
|
|
/// Card internal ECC error
|
|
#define TOKEN_ERR_CARD_ECC BIT(2)
|
|
/// Card controller error
|
|
#define TOKEN_ERR_INTERNAL BIT(1)
|
|
/// Card is locked
|
|
#define TOKEN_ERR_LOCKED BIT(0)
|
|
|
|
|
|
/// Transfer format in SPI mode. See section 7.3.1.1 of SD simplified spec.
|
|
typedef struct {
|
|
// These fields form the command sent from host to the card (6 bytes)
|
|
uint8_t cmd_index : 6;
|
|
uint8_t transmission_bit : 1;
|
|
uint8_t start_bit : 1;
|
|
uint8_t arguments[4];
|
|
uint8_t stop_bit : 1;
|
|
uint8_t crc7 : 7;
|
|
/// Ncr is the dead time between command and response; should be 0xff
|
|
uint8_t ncr;
|
|
/// Response data, should be set by host to 0xff for read operations
|
|
uint8_t r1;
|
|
/// Up to 16 bytes of response. Luckily, this is aligned on 4 byte boundary.
|
|
uint32_t response[4];
|
|
/// response timeout, in milliseconds
|
|
int timeout_ms;
|
|
} sdspi_hw_cmd_t;
|
|
|
|
#define SDSPI_CMD_SIZE 6
|
|
#define SDSPI_NCR_MIN_SIZE 1
|
|
#define SDSPI_NCR_MAX_SIZE 8
|
|
|
|
//the size here contains 6 bytes of CMD, 1 bytes of dummy and the actual response
|
|
#define SDSPI_CMD_NORESP_SIZE (SDSPI_CMD_SIZE+0) //!< Size of the command without any response
|
|
#define SDSPI_CMD_R1_SIZE (SDSPI_CMD_SIZE+SDSPI_NCR_MIN_SIZE+1) //!< Size of the command with R1 response
|
|
#define SDSPI_CMD_R2_SIZE (SDSPI_CMD_SIZE+SDSPI_NCR_MIN_SIZE+2) //!< Size of the command with R1b response
|
|
#define SDSPI_CMD_R3_SIZE (SDSPI_CMD_SIZE+SDSPI_NCR_MIN_SIZE+5) //!< Size of the command with R3 response
|
|
#define SDSPI_CMD_R4_SIZE (SDSPI_CMD_SIZE+SDSPI_NCR_MIN_SIZE+5) //!< Size of the command with R4 response
|
|
#define SDSPI_CMD_R5_SIZE (SDSPI_CMD_SIZE+SDSPI_NCR_MIN_SIZE+2) //!< Size of the command with R5 response
|
|
#define SDSPI_CMD_R7_SIZE (SDSPI_CMD_SIZE+SDSPI_NCR_MIN_SIZE+5) //!< Size of the command with R7 response
|
|
|
|
#define SDSPI_CMD_FLAG_DATA BIT(0) //!< Command has data transfer
|
|
#define SDSPI_CMD_FLAG_WRITE BIT(1) //!< Data is written to the card
|
|
#define SDSPI_CMD_FLAG_RSP_R1 BIT(2) //!< Response format R1 (1 byte)
|
|
#define SDSPI_CMD_FLAG_RSP_R2 BIT(3) //!< Response format R2 (2 bytes)
|
|
#define SDSPI_CMD_FLAG_RSP_R3 BIT(4) //!< Response format R3 (5 bytes)
|
|
#define SDSPI_CMD_FLAG_RSP_R4 BIT(5) //!< Response format R4 (5 bytes)
|
|
#define SDSPI_CMD_FLAG_RSP_R5 BIT(6) //!< Response format R5 (2 bytes)
|
|
#define SDSPI_CMD_FLAG_RSP_R7 BIT(7) //!< Response format R7 (5 bytes)
|
|
#define SDSPI_CMD_FLAG_NORSP BIT(8) //!< Don't expect response (used when sending CMD0 first time).
|
|
#define SDSPI_CMD_FLAG_MULTI_BLK BIT(9) //!< For the write multiblock commands, the start token should be different
|
|
|
|
#define SDSPI_MAX_DATA_LEN 512 //!< Max size of single block transfer
|
|
|
|
void make_hw_cmd(uint32_t opcode, uint32_t arg, int timeout_ms, sdspi_hw_cmd_t *hw_cmd);
|
|
|
|
esp_err_t sdspi_host_start_command(int slot, sdspi_hw_cmd_t *cmd,
|
|
void *data, uint32_t data_size, int flags);
|