esp-idf/examples/storage/ext_flash_fatfs
Angus Gratton b23718995a Merge branch 'bugfix/strict_prototypes' into 'master'
Enable strict prototypes checks

Closes IDFGH-757

See merge request espressif/esp-idf!4546
2019-08-05 09:38:39 +08:00
..
main Merge branch 'bugfix/strict_prototypes' into 'master' 2019-08-05 09:38:39 +08:00
CMakeLists.txt examples: add FATFS in external Flash example 2019-07-26 08:19:42 +02:00
Makefile examples: add FATFS in external Flash example 2019-07-26 08:19:42 +02:00
README.md examples: ext_flash_fatfs: use DIO mode by default 2019-07-28 10:14:04 +02:00

FAT FS on External Flash example

(See the README.md file in the upper level 'examples' directory for more information about examples.)

This example is similar to the wear levelling example, except that it uses an external SPI Flash chip. This can be useful if you need to add more storage to a module with only 4 MB flash size.

The flow of the example is as follows:

  1. Initialize the SPI bus and configure the pins. In this example, VSPI peripheral is used. The pins chosen in this example correspond to IOMUX pins for the VSPI peripheral. If the pin assignment is changed, SPI driver will instead connect the peripheral to the pins using the GPIO Matrix.

  2. Initialize the SPI flash chip. This involves creating a run-time object which describes the flash chip (esp_flash_t), probing the flash chip, and configuring it for the selected read mode. By default this example uses DIO mode, which only requires 4 pins (MOSI, MISO, SCLK, CS). For modes such as QIO and QOUT, additional pins must be connected.

  3. Register the entire area of the Flash chip as a partition (esp_partition_t). This allows other components (FATFS, SPIFFS, NVS, etc) to use the storage provided by the external flash chip.

  4. Do some read and write operations using C standard library functions: create a file, write to it, open it for reading, print the contents to the console.

How to use example

Hardware required

This example needs an SPI NOR Flash chip connected to the ESP32. The SPI Flash chip must have 3.3V logic levels. The example has been tested with Winbond W25Q32 SPI Flash chip.

Use the following pin assignments:

ESP32 pin SPI bus signal SPI Flash pin
GPIO23 MOSI DI
GPIO19 MISO DO
GPIO18 SCLK CLK
GPIO5 CS CMD
unconnected WP
unconnected HOLD
GND GND
VCC VCC

Build and flash

Build the project and flash it to the board, then run monitor tool to view serial output:

idf.py -p PORT flash monitor

(Replace PORT with serial port name.)

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example output

Here is a typical example console output.

I (328) example: Initializing external SPI Flash
I (338) example: Pin assignments:
I (338) example: MOSI: 23   MISO: 19   SCLK: 18   CS:  5
I (348) spi_flash: detected chip: generic
I (348) spi_flash: flash io: dio
I (348) example: Initialized external Flash, size=4096 KB, ID=0xef4016
I (358) example: Adding external Flash as a partition, label="storage", size=4096 KB
I (368) example: Mounting FAT filesystem
I (378) example: FAT FS: 4024 kB total, 4020 kB free
I (378) example: Opening file
I (958) example: File written
I (958) example: Reading file
I (958) example: Read from file: 'Written using ESP-IDF v4.0-dev-1301-g0a1160468'