esp-idf/components/freemodbus/modbus/include/mbconfig.h

/*
 * FreeModbus Libary: A portable Modbus implementation for Modbus ASCII/RTU.
 * Copyright (c) 2006 Christian Walter <wolti@sil.at>
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 * 3. The name of the author may not be used to endorse or promote products
 *    derived from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *
 * File: $Id: mbconfig.h,v 1.15 2010/06/06 13:54:40 wolti Exp $
 *       $Id: mbconfig.h,v 1.60 2013/08/13 21:19:55 Armink Add Master Functions $
 */

#ifndef _MB_CONFIG_H
#define _MB_CONFIG_H

#include "sdkconfig.h" // for KConfig options

#ifdef __cplusplus
PR_BEGIN_EXTERN_C
#endif
/* ----------------------- Defines ------------------------------------------*/
/*! \defgroup modbus_cfg Modbus Configuration
 *
 * Most modules in the protocol stack are completly optional and can be
 * excluded. This is specially important if target resources are very small
 * and program memory space should be saved.<br>
 *
 * All of these settings are available in the file <code>mbconfig.h</code>
 */
/*! \addtogroup modbus_cfg
 *  @{
 */
/*! \brief If Modbus Master ASCII support is enabled. */
#define MB_MASTER_ASCII_ENABLED                 (  CONFIG_FMB_COMM_MODE_ASCII_EN )
/*! \brief If Modbus Master RTU support is enabled. */
#define MB_MASTER_RTU_ENABLED                   (  CONFIG_FMB_COMM_MODE_RTU_EN )
/*! \brief If Modbus Master TCP support is enabled. */
#define MB_MASTER_TCP_ENABLED                   (  CONFIG_FMB_COMM_MODE_TCP_EN )
/*! \brief If Modbus Slave ASCII support is enabled. */
#define MB_SLAVE_ASCII_ENABLED                  (  CONFIG_FMB_COMM_MODE_ASCII_EN )
/*! \brief If Modbus Slave RTU support is enabled. */
#define MB_SLAVE_RTU_ENABLED                    (  CONFIG_FMB_COMM_MODE_RTU_EN )
/*! \brief If Modbus Slave TCP support is enabled. */
#define MB_TCP_ENABLED                          (  CONFIG_FMB_COMM_MODE_TCP_EN )

#if !CONFIG_FMB_COMM_MODE_ASCII_EN && !CONFIG_FMB_COMM_MODE_RTU_EN && !MB_MASTER_TCP_ENABLED && !MB_TCP_ENABLED
#error "None of Modbus communication mode is enabled. Please enable one of (ASCII, RTU, TCP) mode in Kconfig."
#endif

/*! \brief This option defines the number of data bits per ASCII character.
 *
 * A parity bit is added before the stop bit which keeps the actual byte size at 10 bits.
 */
#ifdef CONFIG_FMB_SERIAL_ASCII_BITS_PER_SYMB
#define MB_ASCII_BITS_PER_SYMB                  (  CONFIG_FMB_SERIAL_ASCII_BITS_PER_SYMB )
#endif

/*! \brief The character timeout value for Modbus ASCII.
 *
 * The character timeout value is not fixed for Modbus ASCII and is therefore
 * a configuration option. It should be set to the maximum expected delay
 * time of the network.
 */
#ifdef CONFIG_FMB_SERIAL_ASCII_TIMEOUT_RESPOND_MS
#define MB_ASCII_TIMEOUT_MS                     (  CONFIG_FMB_SERIAL_ASCII_TIMEOUT_RESPOND_MS )
#endif

/*! \brief Timeout to wait in ASCII prior to enabling transmitter.
 *
 * If defined the function calls vMBPortSerialDelay with the argument
 * MB_ASCII_TIMEOUT_WAIT_BEFORE_SEND_MS to allow for a delay before
 * the serial transmitter is enabled. This is required because some
 * targets are so fast that there is no time between receiving and
 * transmitting the frame. If the master is to slow with enabling its
 * receiver then he will not receive the response correctly.
 */
#ifndef MB_ASCII_TIMEOUT_WAIT_BEFORE_SEND_MS
#define MB_ASCII_TIMEOUT_WAIT_BEFORE_SEND_MS    ( 0 )
#endif

/*! \brief Maximum number of Modbus functions codes the protocol stack
 *    should support.
 *
 * The maximum number of supported Modbus functions must be greater than
 * the sum of all enabled functions in this file and custom function
 * handlers. If set to small adding more functions will fail.
 */
#define MB_FUNC_HANDLERS_MAX                    ( 16 )

/*! \brief Number of bytes which should be allocated for the <em>Report Slave ID
 *    </em>command.
 *
 * This number limits the maximum size of the additional segment in the
 * report slave id function. See eMBSetSlaveID(  ) for more information on
 * how to set this value. It is only used if MB_FUNC_OTHER_REP_SLAVEID_ENABLED
 * is set to <code>1</code>.
 */
#define MB_FUNC_OTHER_REP_SLAVEID_BUF           ( 32 )

/*! \brief If the <em>Report Slave ID</em> function should be enabled. */
#define MB_FUNC_OTHER_REP_SLAVEID_ENABLED       (  CONFIG_FMB_CONTROLLER_SLAVE_ID_SUPPORT )

/*! \brief If the <em>Read Input Registers</em> function should be enabled. */
#define MB_FUNC_READ_INPUT_ENABLED              (  1 )

/*! \brief If the <em>Read Holding Registers</em> function should be enabled. */
#define MB_FUNC_READ_HOLDING_ENABLED            (  1 )

/*! \brief If the <em>Write Single Register</em> function should be enabled. */
#define MB_FUNC_WRITE_HOLDING_ENABLED           (  1 )

/*! \brief If the <em>Write Multiple registers</em> function should be enabled. */
#define MB_FUNC_WRITE_MULTIPLE_HOLDING_ENABLED  (  1 )

/*! \brief If the <em>Read Coils</em> function should be enabled. */
#define MB_FUNC_READ_COILS_ENABLED              (  1 )

/*! \brief If the <em>Write Coils</em> function should be enabled. */
#define MB_FUNC_WRITE_COIL_ENABLED              (  1 )

/*! \brief If the <em>Write Multiple Coils</em> function should be enabled. */
#define MB_FUNC_WRITE_MULTIPLE_COILS_ENABLED    (  1 )

/*! \brief If the <em>Read Discrete Inputs</em> function should be enabled. */
#define MB_FUNC_READ_DISCRETE_INPUTS_ENABLED    (  1 )

/*! \brief If the <em>Read/Write Multiple Registers</em> function should be enabled. */
#define MB_FUNC_READWRITE_HOLDING_ENABLED       (  1 )

/*! \brief Check the option to place timer handler into IRAM */
#define MB_PORT_TIMER_ISR_IN_IRAM                          (  CONFIG_FMB_TIMER_ISR_IN_IRAM )

/*! @} */
#ifdef __cplusplus
    PR_END_EXTERN_C
#endif

#if MB_MASTER_RTU_ENABLED || MB_MASTER_ASCII_ENABLED || MB_MASTER_TCP_ENABLED
/*! \brief If master send a broadcast frame, the master will wait time of convert to delay,
 * then master can send other frame */
#define MB_MASTER_DELAY_MS_CONVERT              ( CONFIG_FMB_MASTER_DELAY_MS_CONVERT )
/*! \brief If master send a frame which is not broadcast,the master will wait sometime for slave.
 * And if slave is not respond in this time,the master will process this timeout error.
 * Then master can send other frame */
#define MB_MASTER_TIMEOUT_MS_RESPOND            ( CONFIG_FMB_MASTER_TIMEOUT_MS_RESPOND )
/*! \brief The total slaves in Modbus Master system.
 * \note : The slave ID must be continuous from 1.*/
#define MB_MASTER_TOTAL_SLAVE_NUM               ( 247 )
#endif

#endif