esp-idf/examples/peripherals/uart/uart_echo
songruojing 24a60c12c6 uart: Provide support for esp32c2 and esp32h2
UART examples, unit test, and programming guide are all updated.
2022-03-02 11:29:13 +08:00
..
main uart: Provide support for esp32c2 and esp32h2 2022-03-02 11:29:13 +08:00
CMakeLists.txt example: add nmea0183 parser example 2018-12-07 10:57:34 +08:00
README.md uart: Provide support for esp32c2 and esp32h2 2022-03-02 11:29:13 +08:00

UART Echo Example

(See the README.md file in the upper level 'examples' directory for more information about examples.)

This example demonstrates how to utilize UART interfaces by echoing back to the sender any data received on configured UART.

How to use example

Hardware Required

The example can be run on any ESP32, ESP32-S and ESP32-C series based development board connected to a computer with a single USB cable for flashing and monitoring. The external interface should have 3.3V outputs. You may use e.g. 3.3V compatible USB-to-Serial dongle.

Setup the Hardware

Connect the external serial interface to the board as follows.

  -----------------------------------------------------------------------------------------
  | Target chip Interface | Kconfig Option     | Default ESP Pin      | External UART Pin |
  | ----------------------|--------------------|----------------------|--------------------
  | Transmit Data (TxD)   | EXAMPLE_UART_TXD   | GPIO4                | RxD               |
  | Receive Data (RxD)    | EXAMPLE_UART_RXD   | GPIO5                | TxD               |
  | Ground                | n/a                | GND                  | GND               |
  -----------------------------------------------------------------------------------------

Note: Some GPIOs can not be used with certain chips because they are reserved for internal use. Please refer to UART documentation for selected target.

Optionally, you can set-up and use a serial interface that has RTS and CTS signals in order to verify that the hardware control flow works. Connect the extra signals according to the following table, configure both extra pins in the example code uart_echo_example_main.c by replacing existing UART_PIN_NO_CHANGE macros with the appropriate pin numbers and configure UART1 driver to use the hardware flow control by setting .flow_ctrl = UART_HW_FLOWCTRL_CTS_RTS and adding .rx_flow_ctrl_thresh = 122 to the uart_config structure.

  ---------------------------------------------------------------
  | Target chip Interface | Macro           | External UART Pin |
  | ----------------------|-----------------|--------------------
  | Transmit Data (TxD)   | ECHO_TEST_RTS   | CTS               |
  | Receive Data (RxD)    | ECHO_TEST_CTS   | RTS               |
  | Ground                | n/a             | GND               |
  ---------------------------------------------------------------

Configure the project

Use the command below to configure project using Kconfig menu as showed in the table above. The default Kconfig values can be changed such as: EXAMPLE_TASK_STACK_SIZE, EXAMPLE_UART_BAUD_RATE, EXAMPLE_UART_PORT_NUM (Refer to Kconfig file).

idf.py menuconfig

Build and Flash

Build the project and flash it to the board, then run monitor tool to view serial output:

idf.py -p PORT flash monitor

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

Type some characters in the terminal connected to the external serial interface. As result you should see echo in the same terminal which you used for typing the characters. You can verify if the echo indeed comes from ESP board by disconnecting either TxD or RxD pin: no characters will appear when typing.

Troubleshooting

You are not supposed to see the echo in the terminal which is used for flashing and monitoring, but in the other UART configured through Kconfig can be used.