mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
8d0990806c
Some lcd hardware drivers need different CS setup time. Add pretrans and posttrans parameters to control the CS time. Closes https://github.com/espressif/esp-idf/issues/13071
62 lines
2.8 KiB
C
62 lines
2.8 KiB
C
/*
|
|
* SPDX-FileCopyrightText: 2021-2024 Espressif Systems (Shanghai) CO LTD
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
#pragma once
|
|
|
|
#include <stdbool.h>
|
|
#include "esp_err.h"
|
|
#include "esp_lcd_types.h"
|
|
#include "driver/spi_master.h"
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
typedef int esp_lcd_spi_bus_handle_t; /*!< Type of LCD SPI bus handle */
|
|
|
|
/**
|
|
* @brief Panel IO configuration structure, for SPI interface
|
|
*/
|
|
typedef struct {
|
|
int cs_gpio_num; /*!< GPIO used for CS line */
|
|
int dc_gpio_num; /*!< GPIO used to select the D/C line, set this to -1 if the D/C line is not used */
|
|
int spi_mode; /*!< Traditional SPI mode (0~3) */
|
|
unsigned int pclk_hz; /*!< Frequency of pixel clock */
|
|
size_t trans_queue_depth; /*!< Size of internal transaction queue */
|
|
esp_lcd_panel_io_color_trans_done_cb_t on_color_trans_done; /*!< Callback invoked when color data transfer has finished */
|
|
void *user_ctx; /*!< User private data, passed directly to on_color_trans_done's user_ctx */
|
|
int lcd_cmd_bits; /*!< Bit-width of LCD command */
|
|
int lcd_param_bits; /*!< Bit-width of LCD parameter */
|
|
uint8_t cs_ena_pretrans; /*!< Amount of SPI bit-cycles the cs should be activated before the transmission (0-16) */
|
|
uint8_t cs_ena_posttrans; /*!< Amount of SPI bit-cycles the cs should stay active after the transmission (0-16) */
|
|
struct {
|
|
unsigned int dc_high_on_cmd: 1; /*!< If enabled, DC level = 1 indicates command transfer */
|
|
unsigned int dc_low_on_data: 1; /*!< If enabled, DC level = 0 indicates color data transfer */
|
|
unsigned int dc_low_on_param: 1; /*!< If enabled, DC level = 0 indicates parameter transfer */
|
|
unsigned int octal_mode: 1; /*!< transmit with octal mode (8 data lines), this mode is used to simulate Intel 8080 timing */
|
|
unsigned int quad_mode: 1; /*!< transmit with quad mode (4 data lines), this mode is useful when transmitting LCD parameters (Only use one line for command) */
|
|
unsigned int sio_mode: 1; /*!< Read and write through a single data line (MOSI) */
|
|
unsigned int lsb_first: 1; /*!< transmit LSB bit first */
|
|
unsigned int cs_high_active: 1; /*!< CS line is high active */
|
|
} flags; /*!< Extra flags to fine-tune the SPI device */
|
|
} esp_lcd_panel_io_spi_config_t;
|
|
|
|
/**
|
|
* @brief Create LCD panel IO handle, for SPI interface
|
|
*
|
|
* @param[in] bus SPI bus handle
|
|
* @param[in] io_config IO configuration, for SPI interface
|
|
* @param[out] ret_io Returned IO handle
|
|
* @return
|
|
* - ESP_ERR_INVALID_ARG if parameter is invalid
|
|
* - ESP_ERR_NO_MEM if out of memory
|
|
* - ESP_OK on success
|
|
*/
|
|
esp_err_t esp_lcd_new_panel_io_spi(esp_lcd_spi_bus_handle_t bus, const esp_lcd_panel_io_spi_config_t *io_config, esp_lcd_panel_io_handle_t *ret_io);
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|