mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
8143832041
Add support for 8-line spi for lcd on esp32s2 and esp32s3 Closes https://github.com/espressif/esp-idf/issues/6371
172 lines
8.8 KiB
ReStructuredText
172 lines
8.8 KiB
ReStructuredText
ESP SPI Slave HD (Half Duplex) Mode Protocol
|
|
============================================
|
|
|
|
.. only:: esp32
|
|
|
|
.. warning::
|
|
The driver for ESP32 hasn't been developed yet.
|
|
|
|
.. _esp_spi_slave_caps:
|
|
|
|
SPI Slave Capabilities of Espressif chips
|
|
-----------------------------------------
|
|
|
|
+--------------------+-------+----------+----------+
|
|
| | ESP32 | ESP32-S2 | ESP32-C3 |
|
|
+====================+=======+==========+==========+
|
|
| SPI Slave HD | N | Y (v2) | Y (v2) |
|
|
+--------------------+-------+----------+----------+
|
|
| Tohost intr | | N | N |
|
|
+--------------------+-------+----------+----------+
|
|
| Frhost intr | | 2 \* | 2 \* |
|
|
+--------------------+-------+----------+----------+
|
|
| TX DMA | | Y | Y |
|
|
+--------------------+-------+----------+----------+
|
|
| RX DMA | | Y | Y |
|
|
+--------------------+-------+----------+----------+
|
|
| Shared registers | | 72 | 64 |
|
|
+--------------------+-------+----------+----------+
|
|
|
|
Introduction
|
|
------------
|
|
|
|
In the half duplex mode, the master has to use the protocol defined by the slave to communicate
|
|
with the slave. Each transaction may consist of the following phases (list by the order they
|
|
should exist):
|
|
|
|
- Command: 8-bit, master to slave
|
|
|
|
This phase determines the rest phases of the transactions. See :ref:`spi_slave_hd_supported_cmds`.
|
|
|
|
- Address: 8-bit, master to slave, optional
|
|
|
|
For some commands (WRBUF, RDBUF), this phase specifies the address of shared buffer to write
|
|
to/read from. For other commands with this phase, they are meaningless, but still have to
|
|
exist in the transaction.
|
|
|
|
- Dummy: 8-bit, floating, optional
|
|
|
|
This phase is the turn around time between the master and the slave on the bus, and also
|
|
provides enough time for the slave to prepare the data to send to master.
|
|
|
|
- Data: variable length, the direction is also determined by the command.
|
|
|
|
This may be a data OUT phase, in which the direction is slave to master, or a data IN phase,
|
|
in which the direction is master to slave.
|
|
|
|
The *direction* means which side (master or slave) controls the MOSI, MISO, WP and HD pins.
|
|
|
|
Data IO Modes
|
|
-------------
|
|
|
|
In some IO modes, more data wires can be use to send the data. As a result, the SPI clock cycles
|
|
required for the same amount of data will be less than in 1-bit mode. For example, in QIO mode,
|
|
address and data (IN and OUT) should be sent on all 4 data wires (MOSI, MISO, WP, and HD). Here's
|
|
the modes supported by ESP32-S2 SPI slave and the wire number used in corresponding modes.
|
|
|
|
+-------+------------+------------+--------------+---------+
|
|
| Mode | command WN | address WN | dummy cycles | data WN |
|
|
+=======+============+============+==============+=========+
|
|
| 1-bit | 1 | 1 | 1 | 1 |
|
|
+-------+------------+------------+--------------+---------+
|
|
| DOUT | 1 | 1 | 4 | 2 |
|
|
+-------+------------+------------+--------------+---------+
|
|
| DIO | 1 | 2 | 4 | 2 |
|
|
+-------+------------+------------+--------------+---------+
|
|
| QOUT | 1 | 1 | 4 | 4 |
|
|
+-------+------------+------------+--------------+---------+
|
|
| QIO | 1 | 4 | 4 | 4 |
|
|
+-------+------------+------------+--------------+---------+
|
|
| QPI | 4 | 4 | 4 | 4 |
|
|
+-------+------------+------------+--------------+---------+
|
|
|
|
Normally, which mode is used is determined is determined by the command sent by the master (See
|
|
:ref:`spi_slave_hd_supported_cmds`), except from the QPI mode.
|
|
|
|
QPI Mode
|
|
^^^^^^^^
|
|
|
|
The QPI mode is a special state of the SPI Slave. The master can send ENQPI command to put the
|
|
slave into the QPI mode state. In the QPI mode, the command is also sent in 4-bit, thus it's not
|
|
compatible with the normal modes. The master should only send QPI commands when the slave is in
|
|
the QPI mode. To exit form the QPI mode, master can send EXQPI command.
|
|
|
|
.. _spi_slave_hd_supported_cmds:
|
|
|
|
Supported Commands
|
|
------------------
|
|
|
|
.. note::
|
|
The command name are in a master-oriented direction. For example, WRBUF means master writes
|
|
the buffer of slave.
|
|
|
|
+----------+---------------------+---------+----------+----------------------------------------------------------+
|
|
| Name | Description | Command | Address | Data |
|
|
+==========+=====================+=========+==========+==========================================================+
|
|
| WRBUF | Write buffer | 0x01 | Buf addr | master to slave, no longer than buffer size |
|
|
+----------+---------------------+---------+----------+----------------------------------------------------------+
|
|
| RDBUF | Read buffer | 0x02 | Buf addr | slave to master, no longer than buffer size |
|
|
+----------+---------------------+---------+----------+----------------------------------------------------------+
|
|
| WRDMA | Write DMA | 0x03 | 8 bits | master to slave, no longer than length provided by slave |
|
|
+----------+---------------------+---------+----------+----------------------------------------------------------+
|
|
| RDDMA | Read DMA | 0x04 | 8 bits | slave to master, no longer than length provided by slave |
|
|
+----------+---------------------+---------+----------+----------------------------------------------------------+
|
|
| SEG_DONE | Segments done | 0x05 | - | - |
|
|
+----------+---------------------+---------+----------+----------------------------------------------------------+
|
|
| ENQPI | Enter QPI mode | 0x06 | - | - |
|
|
+----------+---------------------+---------+----------+----------------------------------------------------------+
|
|
| WR_DONE | Write segments done | 0x07 | - | - |
|
|
+----------+---------------------+---------+----------+----------------------------------------------------------+
|
|
| CMD8 | Interrupt | 0x08 | - | - |
|
|
+----------+---------------------+---------+----------+----------------------------------------------------------+
|
|
| CMD9 | Interrupt | 0x09 | - | - |
|
|
+----------+---------------------+---------+----------+----------------------------------------------------------+
|
|
| CMDA | Interrupt | 0x0A | - | - |
|
|
+----------+---------------------+---------+----------+----------------------------------------------------------+
|
|
| EXQPI | Exit QPI mode | 0xDD | - | - |
|
|
+----------+---------------------+---------+----------+----------------------------------------------------------+
|
|
|
|
Moreover, WRBUF, RDBUF, WRDMA, RDDMA commands have their 2-bit and 4-bit version. To do
|
|
transactions in 2-bit or 4-bit mode, send the original command ORed by the corresponding command
|
|
mask below. For example, command 0xA1 means WRBUF in QIO mode.
|
|
|
|
+-------+------+
|
|
| Mode | Mask |
|
|
+=======+======+
|
|
| 1-bit | 0x00 |
|
|
+-------+------+
|
|
| DOUT | 0x10 |
|
|
+-------+------+
|
|
| DIO | 0x50 |
|
|
+-------+------+
|
|
| QOUT | 0x20 |
|
|
+-------+------+
|
|
| QIO | 0xA0 |
|
|
+-------+------+
|
|
| QPI | 0xA0 |
|
|
+-------+------+
|
|
|
|
Segment Transaction Mode
|
|
------------------------
|
|
|
|
Segment transaction mode is the only mode supported by the SPI Slave HD driver for now. In this
|
|
mode, for a transaction the slave load onto the DMA, the master is allowed to read or write in
|
|
segments. This way the master doesn't have to prepare large buffer as the size of data provided
|
|
by the slave. After the master finish reading/writing a buffer, it has to send corresponding
|
|
termination command to the slave as a synchronization signal. The slave driver will update new
|
|
data (if exist) onto the DMA upon seeing the termination command.
|
|
|
|
The termination command is WR_DONE (0x07) for the WRDMA, and CMD8 (0x08) for the RDDMA.
|
|
|
|
Here's an example for the flow the master read data from the slave DMA:
|
|
|
|
1. The slave loads 4092 bytes of data onto the RDDMA
|
|
2. The master do seven RDDMA transactions, each of them are 512 bytes long, and reads the first
|
|
3584 bytes from the slave
|
|
3. The master do the last RDDMA transaction of 512 bytes (equal, longer or shorter than the total
|
|
length loaded by the slave are all allowed). The first 508 bytes are valid data from the
|
|
slave, while the last 4 bytes are meaningless bytes.
|
|
4. The master sends CMD8 to the slave
|
|
5. The slave loads another 4092 bytes of data onto the RDDMA
|
|
6. The master can start new reading transactions after it sends the CMD8
|