esp-idf/examples/protocols/sockets/tcp_server
Ondrej Kosta dd81b56fb6 feat(esp_eth): removed disable of C5 and P4 from examples .build-test-rules
Updated examples to be able to build for C5 and P4.

Added Ethernet support for static_ip example.
2024-08-14 10:07:48 +02:00
..
main feat(examples): add local components via idf_component.yml 2023-09-19 10:38:24 +02:00
CMakeLists.txt feat(examples): add local components via idf_component.yml 2023-09-19 10:38:24 +02:00
pytest_tcp_server.py feat(esp_eth): removed disable of C5 and P4 from examples .build-test-rules 2024-08-14 10:07:48 +02:00
README.md feat(esp_eth): removed disable of C5 and P4 from examples .build-test-rules 2024-08-14 10:07:48 +02:00
sdkconfig.ci CI: update test cases to use different environment variables 2022-07-15 01:16:35 +08:00
sdkconfig.ci.c2_xtal26m ci(wifi): add more wifi runners 2023-07-24 18:09:55 +08:00
sdkconfig.ci.ipv4_only ci(wifi): add more wifi runners 2023-07-24 18:09:55 +08:00
sdkconfig.ci.ipv6_only lwip: Support IPv6 only mode 2023-02-27 08:53:34 +01:00

Supported Targets ESP32 ESP32-C2 ESP32-C3 ESP32-C5 ESP32-C6 ESP32-H2 ESP32-P4 ESP32-S2 ESP32-S3

TCP Server example

(See the README.md file in the upper level 'examples' directory for more information about examples.)

The application creates a TCP socket with the specified port number and waits for a connection request from the client. After accepting a request from the client, connection between server and client is established and the application waits for some data to be received from the client. Received data are printed as ASCII text and retransmitted back to the client.

How to use example

In order to create TCP client that communicates with TCP server example, choose one of the following options.

There are many host-side tools which can be used to interact with the UDP/TCP server/client. One command line tool is netcat which can send and receive many kinds of packets. Note: please replace 192.168.0.167 3333 with desired IPV4/IPV6 address (displayed in monitor console) and port number in the following command.

Ref to the upper level README for more information.

TCP client using netcat

nc 192.168.0.167 3333

Hardware Required

This example can be run on any commonly available ESP32 development board.

Configure the project

idf.py menuconfig

Set following parameters under Example Configuration Options:

  • Set IP version of the example to be IPV4 or IPV6.

  • Set Port number of the socket, that server example will create.

  • Set TCP keep-alive idle time(s) value of TCP keep alive idle time. This time is the time between the last data transmission.

  • Set TCP keep-alive interval time(s) value of TCP keep alive interval time. This time is the interval time of keepalive probe packets.

  • Set TCP keep-alive packet retry send counts value of TCP keep alive packet retry send counts. This is the number of retries of the keepalive probe packet.

Configure Wi-Fi or Ethernet under "Example Connection Configuration" menu. See "Establishing Wi-Fi or Ethernet Connection" section in examples/protocols/README.md for more details.

Build and Flash

Build the project and flash it to the board, then run monitor tool to view serial output:

idf.py -p PORT flash monitor

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Troubleshooting

Start server first, to receive data sent from the client (application).