esp-idf/examples/ethernet/basic/components/ethernet_init/Kconfig.projbuild

243 lines
10 KiB
Plaintext

menu "Example Ethernet Configuration"
orsource "$IDF_PATH/examples/common_components/env_caps/$IDF_TARGET/Kconfig.env_caps"
config EXAMPLE_USE_INTERNAL_ETHERNET
depends on SOC_EMAC_SUPPORTED
select ETH_USE_ESP32_EMAC
default y
bool "Internal EMAC"
help
Use internal Ethernet MAC controller.
if EXAMPLE_USE_INTERNAL_ETHERNET
choice EXAMPLE_ETH_PHY_MODEL
prompt "Ethernet PHY Device"
default EXAMPLE_ETH_PHY_IP101
help
Select the Ethernet PHY device to use in the example.
config EXAMPLE_ETH_PHY_IP101
bool "IP101"
help
IP101 is a single port 10/100 MII/RMII/TP/Fiber Fast Ethernet Transceiver.
Goto http://www.icplus.com.tw/pp-IP101G.html for more information about it.
config EXAMPLE_ETH_PHY_RTL8201
bool "RTL8201/SR8201"
help
RTL8201F/SR8201F is a single port 10/100Mb Ethernet Transceiver with auto MDIX.
Goto http://www.corechip-sz.com/productsview.asp?id=22 for more information about it.
config EXAMPLE_ETH_PHY_LAN87XX
bool "LAN87xx"
help
Below chips are supported:
LAN8710A is a small footprint MII/RMII 10/100 Ethernet Transceiver with HP Auto-MDIX and
flexPWR® Technology.
LAN8720A is a small footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIX Support.
LAN8740A/LAN8741A is a small footprint MII/RMII 10/100 Energy Efficient Ethernet Transceiver
with HP Auto-MDIX and flexPWR® Technology.
LAN8742A is a small footprint RMII 10/100 Ethernet Transceiver with HP Auto-MDIX and
flexPWR® Technology.
Goto https://www.microchip.com for more information about them.
config EXAMPLE_ETH_PHY_DP83848
bool "DP83848"
help
DP83848 is a single port 10/100Mb/s Ethernet Physical Layer Transceiver.
Goto http://www.ti.com/product/DP83848J for more information about it.
config EXAMPLE_ETH_PHY_KSZ80XX
bool "KSZ80xx"
help
With the KSZ80xx series, Microchip offers single-chip 10BASE-T/100BASE-TX
Ethernet Physical Layer Tranceivers (PHY).
The following chips are supported: KSZ8001, KSZ8021, KSZ8031, KSZ8041,
KSZ8051, KSZ8061, KSZ8081, KSZ8091
Goto https://www.microchip.com for more information about them.
endchoice # EXAMPLE_ETH_PHY_MODEL
config EXAMPLE_ETH_MDC_GPIO
int "SMI MDC GPIO number"
range ENV_GPIO_RANGE_MIN ENV_GPIO_OUT_RANGE_MAX
default 23
help
Set the GPIO number used by SMI MDC.
config EXAMPLE_ETH_MDIO_GPIO
int "SMI MDIO GPIO number"
range ENV_GPIO_RANGE_MIN ENV_GPIO_OUT_RANGE_MAX
default 18
help
Set the GPIO number used by SMI MDIO.
config EXAMPLE_ETH_PHY_RST_GPIO
int "PHY Reset GPIO number"
range -1 ENV_GPIO_OUT_RANGE_MAX
default 5
help
Set the GPIO number used to reset PHY chip.
Set to -1 to disable PHY chip hardware reset.
config EXAMPLE_ETH_PHY_ADDR
int "PHY Address"
range 0 31
default 1
help
Set PHY address according your board schematic.
endif # EXAMPLE_USE_INTERNAL_ETHERNET
config EXAMPLE_USE_SPI_ETHERNET
bool "SPI Ethernet"
default n
select ETH_USE_SPI_ETHERNET
help
Use external SPI-Ethernet module(s).
if EXAMPLE_USE_SPI_ETHERNET
config EXAMPLE_SPI_ETHERNETS_NUM
int "Number of SPI Ethernet modules to use at a time"
range 1 2
default 1
help
Set the number of SPI Ethernet modules you want to use at a time. Multiple SPI modules can be connected
to one SPI interface and can be separately accessed based on state of associated Chip Select (CS).
choice EXAMPLE_ETHERNET_TYPE_SPI
prompt "Ethernet SPI"
default EXAMPLE_USE_W5500
help
Select which kind of Ethernet will be used in the example.
config EXAMPLE_USE_DM9051
bool "DM9051 Module"
select ETH_SPI_ETHERNET_DM9051
help
Select external SPI-Ethernet module (DM9051).
config EXAMPLE_USE_KSZ8851SNL
bool "KSZ8851SNL Module"
select ETH_SPI_ETHERNET_KSZ8851SNL
help
Select external SPI-Ethernet module (KSZ8851SNL).
config EXAMPLE_USE_W5500
bool "W5500 Module"
select ETH_SPI_ETHERNET_W5500
help
Select external SPI-Ethernet module (W5500).
endchoice
config EXAMPLE_ETH_SPI_HOST
int "SPI Host Number"
range 0 2
default 1
help
Set the SPI host used to communicate with the SPI Ethernet Controller.
config EXAMPLE_ETH_SPI_SCLK_GPIO
int "SPI SCLK GPIO number"
range ENV_GPIO_RANGE_MIN ENV_GPIO_OUT_RANGE_MAX
default 14 if IDF_TARGET_ESP32
default 12 if IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32S3
default 6 if IDF_TARGET_ESP32C3 || IDF_TARGET_ESP32C2
help
Set the GPIO number used by SPI SCLK.
config EXAMPLE_ETH_SPI_MOSI_GPIO
int "SPI MOSI GPIO number"
range ENV_GPIO_RANGE_MIN ENV_GPIO_OUT_RANGE_MAX
default 13 if IDF_TARGET_ESP32
default 11 if IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32S3
default 7 if IDF_TARGET_ESP32C3 || IDF_TARGET_ESP32C2
help
Set the GPIO number used by SPI MOSI.
config EXAMPLE_ETH_SPI_MISO_GPIO
int "SPI MISO GPIO number"
range ENV_GPIO_RANGE_MIN ENV_GPIO_IN_RANGE_MAX
default 12 if IDF_TARGET_ESP32
default 13 if IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32S3
default 2 if IDF_TARGET_ESP32C3 || IDF_TARGET_ESP32C2
help
Set the GPIO number used by SPI MISO.
config EXAMPLE_ETH_SPI_CLOCK_MHZ
int "SPI clock speed (MHz)"
range 5 80
default 12 if IDF_TARGET_ESP32 || IDF_TARGET_ESP32C3 || IDF_TARGET_ESP32C2
default 36 if IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32S3
help
Set the clock speed (MHz) of SPI interface.
config EXAMPLE_ETH_SPI_CS0_GPIO
int "SPI CS0 GPIO number for SPI Ethernet module #1"
range ENV_GPIO_RANGE_MIN ENV_GPIO_OUT_RANGE_MAX
default 15 if IDF_TARGET_ESP32
default 10 if IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32C3 || IDF_TARGET_ESP32S3 || IDF_TARGET_ESP32C2
help
Set the GPIO number used by SPI CS0, i.e. Chip Select associated with the first SPI Eth module).
config EXAMPLE_ETH_SPI_CS1_GPIO
depends on EXAMPLE_SPI_ETHERNETS_NUM > 1
int "SPI CS1 GPIO number for SPI Ethernet module #2"
range ENV_GPIO_RANGE_MIN ENV_GPIO_OUT_RANGE_MAX
default 32 if IDF_TARGET_ESP32
default 7 if IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32S3
default 8 if IDF_TARGET_ESP32C3
default 3 if IDF_TARGET_ESP32C2
help
Set the GPIO number used by SPI CS1, i.e. Chip Select associated with the second SPI Eth module.
config EXAMPLE_ETH_SPI_INT0_GPIO
int "Interrupt GPIO number SPI Ethernet module #1"
range ENV_GPIO_RANGE_MIN ENV_GPIO_IN_RANGE_MAX
default 4 if IDF_TARGET_ESP32 || IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32C3 || IDF_TARGET_ESP32S3
default 4 if IDF_TARGET_ESP32C2
help
Set the GPIO number used by the first SPI Ethernet module interrupt line.
config EXAMPLE_ETH_SPI_INT1_GPIO
depends on EXAMPLE_SPI_ETHERNETS_NUM > 1
int "Interrupt GPIO number SPI Ethernet module #2"
range ENV_GPIO_RANGE_MIN ENV_GPIO_IN_RANGE_MAX
default 33 if IDF_TARGET_ESP32
default 5 if IDF_TARGET_ESP32S2 || IDF_TARGET_ESP32C3 || IDF_TARGET_ESP32S3 || IDF_TARGET_ESP32C2
help
Set the GPIO number used by the second SPI Ethernet module interrupt line.
config EXAMPLE_ETH_SPI_PHY_RST0_GPIO
int "PHY Reset GPIO number of SPI Ethernet Module #1"
range -1 ENV_GPIO_OUT_RANGE_MAX
default -1
help
Set the GPIO number used to reset PHY chip on the first SPI Ethernet module.
Set to -1 to disable PHY chip hardware reset.
config EXAMPLE_ETH_SPI_PHY_RST1_GPIO
depends on EXAMPLE_SPI_ETHERNETS_NUM > 1
int "PHY Reset GPIO number of SPI Ethernet Module #2"
range -1 ENV_GPIO_OUT_RANGE_MAX
default -1
help
Set the GPIO number used to reset PHY chip on the second SPI Ethernet module.
Set to -1 to disable PHY chip hardware reset.
config EXAMPLE_ETH_SPI_PHY_ADDR0
int "PHY Address of SPI Ethernet Module #1"
range 0 31
default 1
help
Set the first SPI Ethernet module PHY address according your board schematic.
config EXAMPLE_ETH_SPI_PHY_ADDR1
depends on EXAMPLE_SPI_ETHERNETS_NUM > 1
int "PHY Address of SPI Ethernet Module #2"
range 0 31
default 1
help
Set the second SPI Ethernet module PHY address according your board schematic.
endif # EXAMPLE_USE_SPI_ETHERNET
endmenu