esp-idf/components/hal/spi_hal_iram.c

165 lines
5.0 KiB
C

/*
* SPDX-FileCopyrightText: 2015-2023 Espressif Systems (Shanghai) CO LTD
*
* SPDX-License-Identifier: Apache-2.0
*/
// The HAL layer for SPI (common part, in iram)
// make these functions in a seperate file to make sure all LL functions are in the IRAM.
#include "hal/spi_hal.h"
#include "hal/assert.h"
#include "soc/ext_mem_defs.h"
#include "soc/soc_caps.h"
void spi_hal_setup_device(spi_hal_context_t *hal, const spi_hal_dev_config_t *dev)
{
//Configure clock settings
spi_dev_t *hw = hal->hw;
#if SOC_SPI_AS_CS_SUPPORTED
spi_ll_master_set_cksel(hw, dev->cs_pin_id, dev->as_cs);
#endif
spi_ll_master_set_pos_cs(hw, dev->cs_pin_id, dev->positive_cs);
spi_ll_master_set_clock_by_reg(hw, &dev->timing_conf.clock_reg);
//Configure bit order
spi_ll_set_rx_lsbfirst(hw, dev->rx_lsbfirst);
spi_ll_set_tx_lsbfirst(hw, dev->tx_lsbfirst);
spi_ll_master_set_mode(hw, dev->mode);
//Configure misc stuff
spi_ll_set_half_duplex(hw, dev->half_duplex);
spi_ll_set_sio_mode(hw, dev->sio);
//Configure CS pin and timing
spi_ll_master_set_cs_setup(hw, dev->cs_setup);
spi_ll_master_set_cs_hold(hw, dev->cs_hold);
spi_ll_master_select_cs(hw, dev->cs_pin_id);
}
void spi_hal_setup_trans(spi_hal_context_t *hal, const spi_hal_dev_config_t *dev, const spi_hal_trans_config_t *trans)
{
spi_dev_t *hw = hal->hw;
//clear int bit
spi_ll_clear_int_stat(hal->hw);
//We should be done with the transmission.
HAL_ASSERT(spi_ll_get_running_cmd(hw) == 0);
//set transaction line mode
spi_ll_master_set_line_mode(hw, trans->line_mode);
int extra_dummy = 0;
//when no_dummy is not set and in half-duplex mode, sets the dummy bit if RX phase exist
if (trans->rcv_buffer && !dev->no_compensate && dev->half_duplex) {
extra_dummy = dev->timing_conf.timing_dummy;
}
//SPI iface needs to be configured for a delay in some cases.
//configure dummy bits
spi_ll_set_dummy(hw, extra_dummy + trans->dummy_bits);
uint32_t miso_delay_num = 0;
uint32_t miso_delay_mode = 0;
if (dev->timing_conf.timing_miso_delay < 0) {
//if the data comes too late, delay half a SPI clock to improve reading
switch (dev->mode) {
case 0:
miso_delay_mode = 2;
break;
case 1:
miso_delay_mode = 1;
break;
case 2:
miso_delay_mode = 1;
break;
case 3:
miso_delay_mode = 2;
break;
}
miso_delay_num = 0;
} else {
//if the data is so fast that dummy_bit is used, delay some apb clocks to meet the timing
miso_delay_num = extra_dummy ? dev->timing_conf.timing_miso_delay : 0;
miso_delay_mode = 0;
}
spi_ll_set_miso_delay(hw, miso_delay_mode, miso_delay_num);
spi_ll_set_mosi_bitlen(hw, trans->tx_bitlen);
if (dev->half_duplex) {
spi_ll_set_miso_bitlen(hw, trans->rx_bitlen);
} else {
//rxlength is not used in full-duplex mode
spi_ll_set_miso_bitlen(hw, trans->tx_bitlen);
}
//Configure bit sizes, load addr and command
int cmdlen = trans->cmd_bits;
int addrlen = trans->addr_bits;
if (!dev->half_duplex && dev->cs_setup != 0) {
/* The command and address phase is not compatible with cs_ena_pretrans
* in full duplex mode.
*/
cmdlen = 0;
addrlen = 0;
}
spi_ll_set_addr_bitlen(hw, addrlen);
spi_ll_set_command_bitlen(hw, cmdlen);
spi_ll_set_command(hw, trans->cmd, cmdlen, dev->tx_lsbfirst);
spi_ll_set_address(hw, trans->addr, addrlen, dev->tx_lsbfirst);
//Configure keep active CS
spi_ll_master_keep_cs(hw, trans->cs_keep_active);
//Save the transaction attributes for internal usage.
memcpy(&hal->trans_config, trans, sizeof(spi_hal_trans_config_t));
}
void spi_hal_enable_data_line(spi_dev_t *hw, bool mosi_ena, bool miso_ena)
{
spi_ll_enable_mosi(hw, mosi_ena);
spi_ll_enable_miso(hw, miso_ena);
}
void spi_hal_hw_prepare_rx(spi_dev_t *hw)
{
spi_ll_dma_rx_fifo_reset(hw);
spi_ll_infifo_full_clr(hw);
spi_ll_dma_rx_enable(hw, 1);
}
void spi_hal_hw_prepare_tx(spi_dev_t *hw)
{
spi_ll_dma_tx_fifo_reset(hw);
spi_ll_outfifo_empty_clr(hw);
spi_ll_dma_tx_enable(hw, 1);
}
void spi_hal_user_start(const spi_hal_context_t *hal)
{
spi_ll_apply_config(hal->hw);
spi_ll_user_start(hal->hw);
}
bool spi_hal_usr_is_done(const spi_hal_context_t *hal)
{
return spi_ll_usr_is_done(hal->hw);
}
void spi_hal_push_tx_buffer(const spi_hal_context_t *hal, const spi_hal_trans_config_t *hal_trans)
{
if (hal_trans->send_buffer) {
spi_ll_write_buffer(hal->hw, hal_trans->send_buffer, hal_trans->tx_bitlen);
}
//No need to setup anything for RX, we'll copy the result out of the work registers directly later.
}
void spi_hal_fetch_result(const spi_hal_context_t *hal)
{
const spi_hal_trans_config_t *trans = &hal->trans_config;
if (trans->rcv_buffer) {
//Need to copy from SPI regs to result buffer.
spi_ll_read_buffer(hal->hw, trans->rcv_buffer, trans->rx_bitlen);
}
}