esp-idf/components/esp_phy/include/esp_phy_init.h

292 lines
8.2 KiB
C

/*
* SPDX-FileCopyrightText: 2015-2024 Espressif Systems (Shanghai) CO LTD
*
* SPDX-License-Identifier: Apache-2.0
*/
#pragma once
#include <stdint.h>
#include <stdbool.h>
#include "esp_err.h"
#include "sdkconfig.h"
#ifdef __cplusplus
extern "C" {
#endif
/**
* @file
* init parameters and API
*/
/**
* @brief Structure holding PHY init parameters
*/
typedef struct {
#if CONFIG_IDF_TARGET_ESP32C5
uint8_t params[256]; /*!< opaque PHY initialization parameters */
#else
uint8_t params[128]; /*!< opaque PHY initialization parameters */
#endif
} esp_phy_init_data_t;
/**
* @brief PHY enable or disable modem
*/
typedef enum {
PHY_MODEM_WIFI = 1, /*!< PHY modem WIFI */
PHY_MODEM_BT = 2, /*!< PHY modem BT */
PHY_MODEM_IEEE802154 = 4, /*!< PHY modem IEEE802154 */
} esp_phy_modem_t;
/**
* @brief Opaque PHY calibration data
*/
typedef struct {
uint8_t version[4]; /*!< PHY version */
uint8_t mac[6]; /*!< The MAC address of the station */
uint8_t opaque[1894]; /*!< calibration data */
} esp_phy_calibration_data_t;
/**
* @brief PHY calibration mode
*
*/
typedef enum {
PHY_RF_CAL_PARTIAL = 0x00000000, /*!< Do part of RF calibration. This should be used after power-on reset. */
PHY_RF_CAL_NONE = 0x00000001, /*!< Don't do any RF calibration. This mode is only suggested to be used after deep sleep reset. */
PHY_RF_CAL_FULL = 0x00000002 /*!< Do full RF calibration. Produces best results, but also consumes a lot of time and current. Suggested to be used once. */
} esp_phy_calibration_mode_t;
#if CONFIG_ESP_PHY_MULTIPLE_INIT_DATA_BIN
/**
* @brief PHY init data type
*/
typedef enum {
ESP_PHY_INIT_DATA_TYPE_DEFAULT = 0,
ESP_PHY_INIT_DATA_TYPE_SRRC,
ESP_PHY_INIT_DATA_TYPE_FCC,
ESP_PHY_INIT_DATA_TYPE_CE,
ESP_PHY_INIT_DATA_TYPE_NCC,
ESP_PHY_INIT_DATA_TYPE_KCC,
ESP_PHY_INIT_DATA_TYPE_MIC,
ESP_PHY_INIT_DATA_TYPE_IC,
ESP_PHY_INIT_DATA_TYPE_ACMA,
ESP_PHY_INIT_DATA_TYPE_ANATEL,
ESP_PHY_INIT_DATA_TYPE_ISED,
ESP_PHY_INIT_DATA_TYPE_WPC,
ESP_PHY_INIT_DATA_TYPE_OFCA,
ESP_PHY_INIT_DATA_TYPE_IFETEL,
ESP_PHY_INIT_DATA_TYPE_RCM,
ESP_PHY_INIT_DATA_TYPE_NUMBER,
} phy_init_data_type_t;
#endif
/**
* @brief Get PHY init data
*
* If "Use a partition to store PHY init data" option is set in menuconfig,
* This function will load PHY init data from a partition. Otherwise,
* PHY init data will be compiled into the application itself, and this function
* will return a pointer to PHY init data located in read-only memory (DROM).
*
* If "Use a partition to store PHY init data" option is enabled, this function
* may return NULL if the data loaded from flash is not valid.
*
* @note Call esp_phy_release_init_data to release the pointer obtained using
* this function after the call to esp_wifi_init.
*
* @return pointer to PHY init data structure
*/
const esp_phy_init_data_t* esp_phy_get_init_data(void);
/**
* @brief Release PHY init data
* @param data pointer to PHY init data structure obtained from
* esp_phy_get_init_data function
*/
void esp_phy_release_init_data(const esp_phy_init_data_t* data);
/**
* @brief Function called by esp_phy_load_cal_and_init to load PHY calibration data
*
* This is a convenience function which can be used to load PHY calibration
* data from NVS. Data can be stored to NVS using esp_phy_store_cal_data_to_nvs
* function.
*
* If calibration data is not present in the NVS, or
* data is not valid (was obtained for a chip with a different MAC address,
* or obtained for a different version of software), this function will
* return an error.
*
* @param out_cal_data pointer to calibration data structure to be filled with
* loaded data.
* @return ESP_OK on success
*/
esp_err_t esp_phy_load_cal_data_from_nvs(esp_phy_calibration_data_t* out_cal_data);
/**
* @brief Function called by esp_phy_load_cal_and_init to store PHY calibration data
*
* This is a convenience function which can be used to store PHY calibration
* data to the NVS. Calibration data is returned by esp_phy_load_cal_and_init function.
* Data saved using this function to the NVS can later be loaded using
* esp_phy_store_cal_data_to_nvs function.
*
* @param cal_data pointer to calibration data which has to be saved.
* @return ESP_OK on success
*/
esp_err_t esp_phy_store_cal_data_to_nvs(const esp_phy_calibration_data_t* cal_data);
/**
* @brief Erase PHY calibration data which is stored in the NVS
*
* This is a function which can be used to trigger full calibration as a last-resort remedy
* if partial calibration is used. It can be called in the application based on some conditions
* (e.g. an option provided in some diagnostic mode).
*
* @return ESP_OK on success
* @return others on fail. Please refer to NVS API return value error number.
*/
esp_err_t esp_phy_erase_cal_data_in_nvs(void);
/**
* @brief Enable PHY and RF module
*
* PHY and RF module should be enabled in order to use WiFi or BT.
* Now PHY and RF enabling job is done automatically when start WiFi or BT. Users should not
* call this API in their application.
*
* @param modem the modem to call the phy enable.
*/
void esp_phy_enable(esp_phy_modem_t modem);
/**
* @brief Disable PHY and RF module
*
* PHY module should be disabled in order to shutdown WiFi or BT.
* Now PHY and RF disabling job is done automatically when stop WiFi or BT. Users should not
* call this API in their application.
*
* @param modem the modem to call the phy disable.
*/
void esp_phy_disable(esp_phy_modem_t modem);
/**
* @brief Enable BTBB module
*
* BTBB module should be enabled in order to use IEEE802154 or BT.
* Now BTBB enabling job is done automatically when start IEEE802154 or BT. Users should not
* call this API in their application.
*
*/
void esp_btbb_enable(void);
/**
* @brief Disable BTBB module
*
* Disable BTBB module, used by IEEE802154 or Bluetooth.
* Users should not call this API in their application.
*
*/
void esp_btbb_disable(void);
/**
* @brief Load calibration data from NVS and initialize PHY and RF module
*/
void esp_phy_load_cal_and_init(void);
/**
* @brief Initialize backup memory for Phy power up/down
*/
void esp_phy_modem_init(void);
/**
* @brief Deinitialize backup memory for Phy power up/down
* Set phy_init_flag if all modems deinit on ESP32C3
*/
void esp_phy_modem_deinit(void);
#if CONFIG_MAC_BB_PD
/**
* @brief Initialize backup memory for MAC and Baseband power up/down
*/
void esp_mac_bb_pd_mem_init(void);
/**
* @brief Deinitialize backup memory for MAC and Baseband power up/down
*/
void esp_mac_bb_pd_mem_deinit(void);
/**
* @brief Power up MAC and Baseband
*/
void esp_mac_bb_power_up(void);
/**
* @brief Power down MAC and Baseband
*/
void esp_mac_bb_power_down(void);
#endif
/**
* @brief Enable WiFi/BT common clock
*
*/
void esp_phy_common_clock_enable(void);
/**
* @brief Disable WiFi/BT common clock
*
*/
void esp_phy_common_clock_disable(void);
/**
* @brief Get the time stamp when PHY/RF was switched on
* @return return 0 if PHY/RF is never switched on. Otherwise return time in
* microsecond since boot when phy/rf was last switched on
*/
int64_t esp_phy_rf_get_on_ts(void);
/**
* @brief Update the corresponding PHY init type according to the country code of Wi-Fi.
*
* @param country country code
* @return ESP_OK on success.
* @return esp_err_t code describing the error on fail
*/
esp_err_t esp_phy_update_country_info(const char *country);
#if CONFIG_ESP_PHY_MULTIPLE_INIT_DATA_BIN
/**
* @brief Apply PHY init bin to PHY
* @return ESP_OK on success.
* @return ESP_FAIL on fail.
*/
esp_err_t esp_phy_apply_phy_init_data(uint8_t *init_data);
#endif
/**
* @brief Get PHY lib version
* @return PHY lib version.
*/
char * get_phy_version_str(void);
/**
* @brief Set PHY init parameters
* @param param is 1 means combo module
*/
void phy_init_param_set(uint8_t param);
/**
* @brief Wi-Fi RX enable
* @param enable True for enable wifi receiving mode as default, false for closing wifi receiving mode as default.
*/
void phy_wifi_enable_set(uint8_t enable);
#ifdef __cplusplus
}
#endif