esp-idf/components/ethernet/test/test_emac_deinit.c
morris 7bc36d23e1 ethernet: add iperf example to test real bandwidth
1. Add command for Ethernet based on console component.
2. Make cmd_system and iperf a component that can be referenced by other examples
3. Add "version" command to cmd_system.c
4. Clean up the README.md in all ethernet examples[TW#26525]
2018-10-08 09:51:17 +08:00

87 lines
2.3 KiB
C

/**
* @brief This test has just run in the ESP32_Ethernet_V3 board, which featured
* in PoE submodule and TLK110 PHY. The 50MHz clock used by MAC and PHY is
* supplied by external oscillator through GPIO0.
*
* @file test_emac_deinit.c
* @author morris
* @date 2018-08-24
*/
#include <string.h>
#include "unity.h"
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "esp_system.h"
#include "esp_err.h"
#include "esp_event_loop.h"
#include "esp_event.h"
#include "esp_log.h"
#include "esp_eth.h"
#include "rom/gpio.h"
#include "tcpip_adapter.h"
#include "driver/gpio.h"
#include "driver/periph_ctrl.h"
#include "eth_phy/phy_tlk110.h"
#define DEFAULT_ETHERNET_PHY_CONFIG phy_tlk110_default_ethernet_config
static const char *TAG = "eth_test_deinit";
#define PIN_PHY_POWER 17
#define PIN_SMI_MDC 23
#define PIN_SMI_MDIO 18
#define CONFIG_PHY_ADDRESS 31
#define CONFIG_PHY_CLOCK_MODE 0
static void phy_device_power_enable_via_gpio(bool enable)
{
if (!enable) {
DEFAULT_ETHERNET_PHY_CONFIG.phy_power_enable(false);
}
gpio_pad_select_gpio(PIN_PHY_POWER);
gpio_set_direction(PIN_PHY_POWER, GPIO_MODE_OUTPUT);
if (enable == true) {
gpio_set_level(PIN_PHY_POWER, 1);
ESP_LOGI(TAG, "power on ethernet phy");
} else {
gpio_set_level(PIN_PHY_POWER, 0);
ESP_LOGI(TAG, "power off ethernet phy");
}
vTaskDelay(1); // Allow the power up/down to take effect, min 300us
if (enable) {
/* operates the default phy-specific power on function */
DEFAULT_ETHERNET_PHY_CONFIG.phy_power_enable(true);
}
}
static void eth_gpio_config_rmii(void)
{
phy_rmii_configure_data_interface_pins();
phy_rmii_smi_configure_pins(PIN_SMI_MDC, PIN_SMI_MDIO);
}
TEST_CASE("test emac deinit", "[ethernet][ignore]")
{
eth_config_t config = DEFAULT_ETHERNET_PHY_CONFIG;
config.phy_addr = CONFIG_PHY_ADDRESS;
config.gpio_config = eth_gpio_config_rmii;
config.tcpip_input = tcpip_adapter_eth_input;
config.clock_mode = CONFIG_PHY_CLOCK_MODE;
config.phy_power_enable = phy_device_power_enable_via_gpio;
ESP_ERROR_CHECK(esp_eth_init(&config));
ESP_ERROR_CHECK(esp_eth_enable());
vTaskDelay(2000 / portTICK_RATE_MS);
ESP_ERROR_CHECK(esp_eth_disable());
ESP_ERROR_CHECK(esp_eth_deinit());
}