mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
742f8e7f8a
1. ref_clock used in unit tests occasionally produces time off by ~100 microseconds shortly after being started. Add a delay to let ref_clock stabilise, until the cause is found. 2. Reduce roundoff error accumulation which would occasionally cause the test to fail, by choosing an overflow value which can be divided by APB frequency. 3. Move time sampling part of the test into an IRAM function to reduce variations due to cache behavior. 4. Remove calculation of "standard deviation" in the test, as what was calculated was not actually standard deviation, and it did not add any useful information.
171 lines
6.5 KiB
C
171 lines
6.5 KiB
C
// Copyright 2017 Espressif Systems (Shanghai) PTE LTD
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
//
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
/* Unit tests need to have access to reliable timestamps even if CPU and APB
|
|
* clock frequencies change over time. This reference clock is built upon two
|
|
* peripherals: one RMT channel and one PCNT channel, plus one GPIO to connect
|
|
* these peripherals.
|
|
*
|
|
* RMT channel is configured to use REF_TICK as clock source, which is a 1 MHz
|
|
* clock derived from APB_CLK using a set of dividers. The divider is changed
|
|
* automatically by hardware depending on the current clock source of APB_CLK.
|
|
* For example, if APB_CLK is derived from PLL, one divider is used, and when
|
|
* APB_CLK is derived from XTAL, another divider is used. RMT channel clocked
|
|
* by REF_TICK is configured to generate a continuous 0.5 MHz signal, which is
|
|
* connected to a GPIO. PCNT takes the input signal from this GPIO and counts
|
|
* the edges (which occur at 1MHz frequency). PCNT counter is only 16 bit wide,
|
|
* so an interrupt is configured to trigger when the counter reaches 30000,
|
|
* incrementing a 32-bit millisecond counter maintained by software.
|
|
* Together these two counters may be used at any time to obtain the timestamp.
|
|
*/
|
|
|
|
#include "test_utils.h"
|
|
#include "soc/rmt_struct.h"
|
|
#include "soc/pcnt_struct.h"
|
|
#include "soc/pcnt_reg.h"
|
|
#include "soc/gpio_sig_map.h"
|
|
#include "soc/dport_reg.h"
|
|
#include "rom/gpio.h"
|
|
#include "rom/ets_sys.h"
|
|
#include "driver/gpio.h"
|
|
#include "esp_intr_alloc.h"
|
|
#include "freertos/FreeRTOS.h"
|
|
#include "driver/periph_ctrl.h"
|
|
|
|
/* Select which RMT and PCNT channels, and GPIO to use */
|
|
#define REF_CLOCK_RMT_CHANNEL 7
|
|
#define REF_CLOCK_PCNT_UNIT 0
|
|
#define REF_CLOCK_GPIO 21
|
|
|
|
#define REF_CLOCK_PRESCALER_MS 30
|
|
|
|
static void IRAM_ATTR pcnt_isr(void* arg);
|
|
|
|
static intr_handle_t s_intr_handle;
|
|
static portMUX_TYPE s_lock = portMUX_INITIALIZER_UNLOCKED;
|
|
static volatile uint32_t s_milliseconds;
|
|
|
|
void ref_clock_init()
|
|
{
|
|
assert(s_intr_handle == NULL && "already initialized");
|
|
|
|
// Route RMT output to GPIO matrix
|
|
gpio_matrix_out(REF_CLOCK_GPIO, RMT_SIG_OUT0_IDX + REF_CLOCK_RMT_CHANNEL, false, false);
|
|
|
|
|
|
// Initialize RMT
|
|
periph_module_enable(PERIPH_RMT_MODULE);
|
|
RMT.apb_conf.fifo_mask = 1;
|
|
rmt_item32_t data = {
|
|
.duration0 = 1,
|
|
.level0 = 1,
|
|
.duration1 = 0,
|
|
.level1 = 0
|
|
};
|
|
RMTMEM.chan[REF_CLOCK_RMT_CHANNEL].data32[0] = data;
|
|
RMTMEM.chan[REF_CLOCK_RMT_CHANNEL].data32[1].val = 0;
|
|
|
|
|
|
RMT.conf_ch[REF_CLOCK_RMT_CHANNEL].conf0.clk_en = 1;
|
|
RMT.conf_ch[REF_CLOCK_RMT_CHANNEL].conf1.tx_start = 0;
|
|
RMT.conf_ch[REF_CLOCK_RMT_CHANNEL].conf1.mem_owner = 0;
|
|
RMT.conf_ch[REF_CLOCK_RMT_CHANNEL].conf1.mem_rd_rst = 1;
|
|
RMT.conf_ch[REF_CLOCK_RMT_CHANNEL].conf1.apb_mem_rst = 1;
|
|
RMT.conf_ch[REF_CLOCK_RMT_CHANNEL].conf0.carrier_en = 0;
|
|
RMT.conf_ch[REF_CLOCK_RMT_CHANNEL].conf0.div_cnt = 1;
|
|
RMT.conf_ch[REF_CLOCK_RMT_CHANNEL].conf0.mem_size = 1;
|
|
RMT.conf_ch[REF_CLOCK_RMT_CHANNEL].conf1.ref_always_on = 0;
|
|
RMT.conf_ch[REF_CLOCK_RMT_CHANNEL].conf1.tx_conti_mode = 1;
|
|
RMT.conf_ch[REF_CLOCK_RMT_CHANNEL].conf1.tx_start = 1;
|
|
|
|
// Route signal to PCNT
|
|
int pcnt_sig_idx = (REF_CLOCK_PCNT_UNIT < 5) ?
|
|
PCNT_SIG_CH0_IN0_IDX + 4 * REF_CLOCK_PCNT_UNIT :
|
|
PCNT_SIG_CH0_IN5_IDX + 4 * (REF_CLOCK_PCNT_UNIT - 5);
|
|
gpio_matrix_in(REF_CLOCK_GPIO, pcnt_sig_idx, false);
|
|
if (REF_CLOCK_GPIO != 20) {
|
|
PIN_INPUT_ENABLE(GPIO_PIN_MUX_REG[REF_CLOCK_GPIO]);
|
|
} else {
|
|
PIN_INPUT_ENABLE(PERIPHS_IO_MUX_GPIO20_U);
|
|
}
|
|
|
|
// Initialize PCNT
|
|
periph_module_enable(PERIPH_PCNT_MODULE);
|
|
|
|
PCNT.conf_unit[REF_CLOCK_PCNT_UNIT].conf0.ch0_hctrl_mode = 0;
|
|
PCNT.conf_unit[REF_CLOCK_PCNT_UNIT].conf0.ch0_lctrl_mode = 0;
|
|
PCNT.conf_unit[REF_CLOCK_PCNT_UNIT].conf0.ch0_pos_mode = 1;
|
|
PCNT.conf_unit[REF_CLOCK_PCNT_UNIT].conf0.ch0_neg_mode = 1;
|
|
PCNT.conf_unit[REF_CLOCK_PCNT_UNIT].conf0.thr_l_lim_en = 0;
|
|
PCNT.conf_unit[REF_CLOCK_PCNT_UNIT].conf0.thr_h_lim_en = 1;
|
|
PCNT.conf_unit[REF_CLOCK_PCNT_UNIT].conf0.thr_zero_en = 0;
|
|
PCNT.conf_unit[REF_CLOCK_PCNT_UNIT].conf0.thr_thres0_en = 0;
|
|
PCNT.conf_unit[REF_CLOCK_PCNT_UNIT].conf0.thr_thres1_en = 0;
|
|
PCNT.conf_unit[REF_CLOCK_PCNT_UNIT].conf2.cnt_h_lim = REF_CLOCK_PRESCALER_MS * 1000;
|
|
|
|
// Enable PCNT and wait for it to start counting
|
|
PCNT.ctrl.val &= ~(BIT(REF_CLOCK_PCNT_UNIT * 2 + 1));
|
|
PCNT.ctrl.val |= BIT(REF_CLOCK_PCNT_UNIT * 2);
|
|
PCNT.ctrl.val &= ~BIT(REF_CLOCK_PCNT_UNIT * 2);
|
|
|
|
ets_delay_us(10000);
|
|
|
|
// Enable interrupt
|
|
s_milliseconds = 0;
|
|
ESP_ERROR_CHECK(esp_intr_alloc(ETS_PCNT_INTR_SOURCE, ESP_INTR_FLAG_IRAM, pcnt_isr, NULL, &s_intr_handle));
|
|
PCNT.int_clr.val = BIT(REF_CLOCK_PCNT_UNIT);
|
|
PCNT.int_ena.val = BIT(REF_CLOCK_PCNT_UNIT);
|
|
}
|
|
|
|
static void IRAM_ATTR pcnt_isr(void* arg)
|
|
{
|
|
portENTER_CRITICAL(&s_lock);
|
|
PCNT.int_clr.val = BIT(REF_CLOCK_PCNT_UNIT);
|
|
s_milliseconds += REF_CLOCK_PRESCALER_MS;
|
|
portEXIT_CRITICAL(&s_lock);
|
|
}
|
|
|
|
void ref_clock_deinit()
|
|
{
|
|
assert(s_intr_handle && "deinit called without init");
|
|
|
|
// Disable interrupt
|
|
PCNT.int_ena.val &= ~BIT(REF_CLOCK_PCNT_UNIT);
|
|
esp_intr_free(s_intr_handle);
|
|
s_intr_handle = NULL;
|
|
|
|
// Disable RMT
|
|
RMT.conf_ch[REF_CLOCK_RMT_CHANNEL].conf1.tx_start = 0;
|
|
RMT.conf_ch[REF_CLOCK_RMT_CHANNEL].conf0.clk_en = 0;
|
|
periph_module_disable(PERIPH_RMT_MODULE);
|
|
|
|
// Disable PCNT
|
|
PCNT.ctrl.val |= ~(BIT(REF_CLOCK_PCNT_UNIT * 2 + 1));
|
|
periph_module_disable(PERIPH_PCNT_MODULE);
|
|
}
|
|
|
|
uint64_t ref_clock_get()
|
|
{
|
|
portENTER_CRITICAL(&s_lock);
|
|
uint32_t microseconds = PCNT.cnt_unit[REF_CLOCK_PCNT_UNIT].cnt_val;
|
|
uint32_t milliseconds = s_milliseconds;
|
|
if (PCNT.int_st.val & BIT(REF_CLOCK_PCNT_UNIT)) {
|
|
// refresh counter value, in case the overflow has happened after reading cnt_val
|
|
microseconds = PCNT.cnt_unit[REF_CLOCK_PCNT_UNIT].cnt_val;
|
|
milliseconds += REF_CLOCK_PRESCALER_MS;
|
|
}
|
|
portEXIT_CRITICAL(&s_lock);
|
|
return 1000 * (uint64_t) milliseconds + (uint64_t) microseconds;
|
|
}
|