esp-idf/components/soc/esp32/uart_periph.c
Omar Chebib 779e7400b0 uart: uart_set_pin function will now use IOMUX whenever possible
By using IOMUX instead of GPIO Matrix for UART, it is now possible
on ESP32 boards to use the UART as a wake up source even if it is
not used as a console.
For other boards where this issue was not present, using IOMUX has
the advantage to be faster than using GPIO matrix, so a highest
baudrate can be used
2021-08-04 12:48:30 +08:00

123 lines
3.7 KiB
C

// Copyright 2015-2019 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#include "soc/uart_periph.h"
/*
Bunch of constants for every UART peripheral: GPIO signals, irqs, hw addr of registers etc
*/
const uart_signal_conn_t uart_periph_signal[SOC_UART_NUM] = {
{
.pins = {
[SOC_UART_TX_PIN_IDX] = {
.default_gpio = U0TXD_GPIO_NUM,
.iomux_func = U0TXD_MUX_FUNC,
.input = 0,
.signal = U0TXD_OUT_IDX,
},
[SOC_UART_RX_PIN_IDX] = {
.default_gpio = U0RXD_GPIO_NUM,
.iomux_func = U0RXD_MUX_FUNC,
.input = 1,
.signal = U0RXD_IN_IDX,
},
[SOC_UART_RTS_PIN_IDX] = {
.default_gpio = U0RTS_GPIO_NUM,
.iomux_func = U0RTS_MUX_FUNC,
.input = 0,
.signal = U0RTS_OUT_IDX,
},
[SOC_UART_CTS_PIN_IDX] = {
.default_gpio = U0CTS_GPIO_NUM,
.iomux_func = U0CTS_MUX_FUNC,
.input = 1,
.signal = U0CTS_IN_IDX,
}
},
.irq = ETS_UART0_INTR_SOURCE,
.module = PERIPH_UART0_MODULE,
},
{
.pins = {
[SOC_UART_TX_PIN_IDX] = {
.default_gpio = U1TXD_GPIO_NUM,
.iomux_func = U1TXD_MUX_FUNC,
.input = 0,
.signal = U1TXD_OUT_IDX,
},
[SOC_UART_RX_PIN_IDX] = {
.default_gpio = U1RXD_GPIO_NUM,
.iomux_func = U1RXD_MUX_FUNC,
.input = 1,
.signal = U1RXD_IN_IDX,
},
[SOC_UART_RTS_PIN_IDX] = {
.default_gpio = U1RTS_GPIO_NUM,
.iomux_func = U1RTS_MUX_FUNC,
.input = 0,
.signal = U1RTS_OUT_IDX,
},
[SOC_UART_CTS_PIN_IDX] = {
.default_gpio = U1CTS_GPIO_NUM,
.iomux_func = U1CTS_MUX_FUNC,
.input = 1,
.signal = U1CTS_IN_IDX,
},
},
.irq = ETS_UART1_INTR_SOURCE,
.module = PERIPH_UART1_MODULE,
},
{
.pins = {
[SOC_UART_TX_PIN_IDX] = {
.default_gpio = U2TXD_GPIO_NUM,
.iomux_func = U2TXD_MUX_FUNC,
.input = 0,
.signal = U2TXD_OUT_IDX,
},
[SOC_UART_RX_PIN_IDX] = {
.default_gpio = U2RXD_GPIO_NUM,
.iomux_func = U2RXD_MUX_FUNC,
.input = 1,
.signal = U2RXD_IN_IDX,
},
[SOC_UART_RTS_PIN_IDX] = {
.default_gpio = U2RTS_GPIO_NUM,
.iomux_func = U2RTS_MUX_FUNC,
.input = 0,
.signal = U2RTS_OUT_IDX,
},
[SOC_UART_CTS_PIN_IDX] = {
.default_gpio = U2CTS_GPIO_NUM,
.iomux_func = U2CTS_MUX_FUNC,
.input = 1,
.signal = U2CTS_IN_IDX,
}
},
.irq = ETS_UART2_INTR_SOURCE,
.module = PERIPH_UART2_MODULE,
}
};