mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
647dea9395
During HAL layer refactoring and new chip bringup, we have several caps.h for each part, to reduce the conflicts to minimum. But this is The capabilities headers will be relataive stable once completely written (maybe after the featues are supported by drivers). Now ESP32 and ESP32-S2 drivers are relative stable, making it a good time to combine all these caps.h into one soc_caps.h This cleanup also move HAL config and pin config into separated files, to make the responsibilities of these headers more clear. This is helpful for the stabilities of soc_caps.h because we want to make it public some day.
88 lines
2.9 KiB
C
88 lines
2.9 KiB
C
// Copyright 2010-2020 Espressif Systems (Shanghai) PTE LTD
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
//
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
#pragma once
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
#include <stdint.h>
|
|
#include <stdbool.h>
|
|
#include "soc/gpio_pins.h" //for GPIO_MATRIX_CONST_ONE_INPUT, GPIO_MATRIX_CONST_ZERO_INPUT
|
|
|
|
/**
|
|
* @brief Configure IO Pad as General Purpose IO,
|
|
* so that it can be connected to internal Matrix,
|
|
* then combined with one or more peripheral signals.
|
|
*
|
|
* @param iopad_num IO Pad number
|
|
*/
|
|
void esp_rom_gpio_pad_select_gpio(uint32_t iopad_num);
|
|
|
|
/**
|
|
* @brief Enable internal pull up, and disable internal pull down.
|
|
*
|
|
* @param iopad_num IO Pad number
|
|
*/
|
|
void esp_rom_gpio_pad_pullup_only(uint32_t iopad_num);
|
|
|
|
/**
|
|
* @brief Unhold the IO Pad.
|
|
* @note When the Pad is set to hold, the state is latched at that moment and won't get changed.
|
|
*
|
|
* @param iopad_num IP Pad number
|
|
*/
|
|
void esp_rom_gpio_pad_unhold(uint32_t gpio_num);
|
|
|
|
/**
|
|
* @brief Set IO Pad current drive capability.
|
|
*
|
|
* @param iopad_num IO Pad number
|
|
* @param drv Numeric to indicate the capability of current drive
|
|
* - 0: 5mA
|
|
* - 1: 10mA
|
|
* - 2: 20mA
|
|
* - 3: 40mA
|
|
*/
|
|
void esp_rom_gpio_pad_set_drv(uint32_t iopad_num, uint32_t drv);
|
|
|
|
/**
|
|
* @brief Combine a GPIO input with a peripheral signal, which tagged as input attribute.
|
|
*
|
|
* @note There's no limitation on the number of signals that a GPIO can combine with.
|
|
*
|
|
* @param gpio_num GPIO number, especially, `GPIO_MATRIX_CONST_ZERO_INPUT` means connect logic 0 to signal
|
|
* `GPIO_MATRIX_CONST_ONE_INPUT` means connect logic 1 to signal
|
|
* @param signal_idx Peripheral signal index (tagged as input attribute)
|
|
* @param inv Whether the GPIO input to be inverted or not
|
|
*/
|
|
void esp_rom_gpio_connect_in_signal(uint32_t gpio_num, uint32_t signal_idx, bool inv);
|
|
|
|
/**
|
|
* @brief Combine a peripheral signal which tagged as output attribute with a GPIO.
|
|
*
|
|
* @note There's no limitation on the number of signals that a GPIO can combine with.
|
|
*
|
|
* @param gpio_num GPIO number
|
|
* @param signal_idx Peripheral signal index (tagged as output attribute)
|
|
* @param out_inv Whether to signal to be inverted or not
|
|
* @param oen_inv Whether the output enable control is inverted or not
|
|
*/
|
|
void esp_rom_gpio_connect_out_signal(uint32_t gpio_num, uint32_t signal_idx, bool out_inv, bool oen_inv);
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|