mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
984ee9dd38
Due to HW limitation, we don't support this anymore. On c3, ADC2 under oneshot mode is not stable. However, you can enable CONFIG_ADC_ONESHOT_FORCE_USE_ADC2_ON_C3 to force use ADC2. Refer to errata to know more details: https://www.espressif.com/sites/default/files/documentation/esp32-c3_errata_en.pdf
196 lines
9.1 KiB
Plaintext
196 lines
9.1 KiB
Plaintext
menu "Driver configurations"
|
|
|
|
menu "ADC configuration"
|
|
|
|
config ADC_FORCE_XPD_FSM
|
|
bool "Use the FSM to control ADC power"
|
|
default n
|
|
help
|
|
ADC power can be controlled by the FSM instead of software. This allows the ADC to
|
|
be shut off when it is not working leading to lower power consumption. However
|
|
using the FSM control ADC power will increase the noise of ADC.
|
|
|
|
config ADC_DISABLE_DAC
|
|
bool "Disable DAC when ADC2 is used on GPIO 25 and 26"
|
|
default y
|
|
help
|
|
If this is set, the ADC2 driver will disable the output of the DAC corresponding to the specified
|
|
channel. This is the default value.
|
|
|
|
For testing, disable this option so that we can measure the output of DAC by internal ADC.
|
|
|
|
config ADC_CONTINUOUS_FORCE_USE_ADC2_ON_C3_S3
|
|
depends on IDF_TARGET_ESP32C3
|
|
bool "Force use ADC2 continumous mode on ESP32C3"
|
|
default n
|
|
help
|
|
On ESP32C3, ADC2 Digital Controller is not stable. Therefore,
|
|
ADC2 continuous mode is not suggested on ESP32C3
|
|
|
|
If you stick to this, you can enable this option to force use ADC2 under above conditions.
|
|
For more details, you can search for errata on espressif website.
|
|
|
|
config ADC_ONESHOT_FORCE_USE_ADC2_ON_C3
|
|
depends on IDF_TARGET_ESP32C3
|
|
bool "Force use ADC2 oneshot mode on ESP32C3"
|
|
default n
|
|
help
|
|
On ESP32C3, ADC2 Digital Controller is not stable. Therefore,
|
|
ADC2 oneshot mode is not suggested on ESP32C3
|
|
|
|
If you stick to this, you can enable this option to force use ADC2 under above conditions.
|
|
For more details, you can search for errata on espressif website.
|
|
|
|
endmenu # ADC Configuration
|
|
|
|
menu "SPI configuration"
|
|
|
|
config SPI_MASTER_IN_IRAM
|
|
bool "Place transmitting functions of SPI master into IRAM"
|
|
default n
|
|
select SPI_MASTER_ISR_IN_IRAM
|
|
help
|
|
Normally only the ISR of SPI master is placed in the IRAM, so that it
|
|
can work without the flash when interrupt is triggered.
|
|
For other functions, there's some possibility that the flash cache
|
|
miss when running inside and out of SPI functions, which may increase
|
|
the interval of SPI transactions.
|
|
Enable this to put ``queue_trans``, ``get_trans_result`` and
|
|
``transmit`` functions into the IRAM to avoid possible cache miss.
|
|
|
|
During unit test, this is enabled to measure the ideal case of api.
|
|
|
|
config SPI_MASTER_ISR_IN_IRAM
|
|
bool "Place SPI master ISR function into IRAM"
|
|
default y
|
|
help
|
|
Place the SPI master ISR in to IRAM to avoid possible cache miss.
|
|
|
|
Also you can forbid the ISR being disabled during flash writing
|
|
access, by add ESP_INTR_FLAG_IRAM when initializing the driver.
|
|
|
|
config SPI_SLAVE_IN_IRAM
|
|
bool "Place transmitting functions of SPI slave into IRAM"
|
|
default n
|
|
select SPI_SLAVE_ISR_IN_IRAM
|
|
help
|
|
Normally only the ISR of SPI slave is placed in the IRAM, so that it
|
|
can work without the flash when interrupt is triggered.
|
|
For other functions, there's some possibility that the flash cache
|
|
miss when running inside and out of SPI functions, which may increase
|
|
the interval of SPI transactions.
|
|
Enable this to put ``queue_trans``, ``get_trans_result`` and
|
|
``transmit`` functions into the IRAM to avoid possible cache miss.
|
|
|
|
config SPI_SLAVE_ISR_IN_IRAM
|
|
bool "Place SPI slave ISR function into IRAM"
|
|
default y
|
|
help
|
|
Place the SPI slave ISR in to IRAM to avoid possible cache miss.
|
|
|
|
Also you can forbid the ISR being disabled during flash writing
|
|
access, by add ESP_INTR_FLAG_IRAM when initializing the driver.
|
|
|
|
endmenu # SPI Configuration
|
|
|
|
menu "TWAI configuration"
|
|
|
|
config TWAI_ISR_IN_IRAM
|
|
bool "Place TWAI ISR function into IRAM"
|
|
default n
|
|
help
|
|
Place the TWAI ISR in to IRAM. This will allow the ISR to avoid
|
|
cache misses, and also be able to run whilst the cache is disabled
|
|
(such as when writing to SPI Flash).
|
|
Note that if this option is enabled:
|
|
- Users should also set the ESP_INTR_FLAG_IRAM in the driver
|
|
configuration structure when installing the driver (see docs for
|
|
specifics).
|
|
- Alert logging (i.e., setting of the TWAI_ALERT_AND_LOG flag)
|
|
will have no effect.
|
|
|
|
config TWAI_ERRATA_FIX_BUS_OFF_REC
|
|
bool "Add SW workaround for REC change during bus-off"
|
|
depends on IDF_TARGET_ESP32
|
|
default n
|
|
help
|
|
When the bus-off condition is reached, the REC should be reset to 0 and frozen (via LOM) by the
|
|
driver's ISR. However on the ESP32, there is an edge case where the REC will increase before the
|
|
driver's ISR can respond in time (e.g., due to the rapid occurrence of bus errors), thus causing the
|
|
REC to be non-zero after bus-off. A non-zero REC can prevent bus-off recovery as the bus-off recovery
|
|
condition is that both TEC and REC become 0. Enabling this option will add a workaround in the driver
|
|
to forcibly reset REC to zero on reaching bus-off.
|
|
|
|
config TWAI_ERRATA_FIX_TX_INTR_LOST
|
|
bool "Add SW workaround for TX interrupt lost errata"
|
|
depends on IDF_TARGET_ESP32
|
|
default n
|
|
help
|
|
On the ESP32, when a transmit interrupt occurs, and interrupt register is read on the same APB clock
|
|
cycle, the transmit interrupt could be lost. Enabling this option will add a workaround that checks the
|
|
transmit buffer status bit to recover any lost transmit interrupt.
|
|
|
|
config TWAI_ERRATA_FIX_RX_FRAME_INVALID
|
|
bool "Add SW workaround for invalid RX frame errata"
|
|
depends on IDF_TARGET_ESP32
|
|
default n
|
|
help
|
|
On the ESP32, when receiving a data or remote frame, if a bus error occurs in the data or CRC field,
|
|
the data of the next received frame could be invalid. Enabling this option will add a workaround that
|
|
will reset the peripheral on detection of this errata condition. Note that if a frame is transmitted on
|
|
the bus whilst the reset is ongoing, the message will not be receive by the peripheral sent on the bus
|
|
during the reset, the message will be lost.
|
|
|
|
config TWAI_ERRATA_FIX_RX_FIFO_CORRUPT
|
|
bool "Add SW workaround for RX FIFO corruption errata"
|
|
depends on IDF_TARGET_ESP32
|
|
default n
|
|
help
|
|
On the ESP32, when the RX FIFO overruns and the RX message counter maxes out at 64 messages, the entire
|
|
RX FIFO is no longer recoverable. Enabling this option will add a workaround that resets the peripheral
|
|
on detection of this errata condition. Note that if a frame is being sent on the bus during the reset
|
|
bus during the reset, the message will be lost.
|
|
|
|
endmenu # TWAI Configuration
|
|
|
|
menu "UART configuration"
|
|
|
|
config UART_ISR_IN_IRAM
|
|
bool "Place UART ISR function into IRAM"
|
|
default n
|
|
help
|
|
If this option is not selected, UART interrupt will be disabled for a long time and
|
|
may cause data lost when doing spi flash operation.
|
|
|
|
endmenu # UART Configuration
|
|
|
|
menu "RTCIO configuration"
|
|
visible if IDF_TARGET_ESP32
|
|
|
|
config RTCIO_SUPPORT_RTC_GPIO_DESC
|
|
bool "Support array `rtc_gpio_desc` for ESP32"
|
|
depends on IDF_TARGET_ESP32
|
|
default n
|
|
help
|
|
The the array `rtc_gpio_desc` will don't compile by default.
|
|
If this option is selected, the array `rtc_gpio_desc` can be compile.
|
|
If user use this array, please enable this configuration.
|
|
|
|
endmenu # RTCIO Configuration
|
|
|
|
menu "GPIO Configuration"
|
|
visible if IDF_TARGET_ESP32
|
|
|
|
config GPIO_ESP32_SUPPORT_SWITCH_SLP_PULL
|
|
bool "Support light sleep GPIO pullup/pulldown configuration for ESP32"
|
|
depends on IDF_TARGET_ESP32
|
|
help
|
|
This option is intended to fix the bug that ESP32 is not able to switch to configured
|
|
pullup/pulldown mode in sleep.
|
|
If this option is selected, chip will automatically emulate the behaviour of switching,
|
|
and about 450B of source codes would be placed into IRAM.
|
|
|
|
endmenu # GPIO Configuration
|
|
|
|
endmenu # Driver configurations
|