mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
113 lines
7.0 KiB
ReStructuredText
113 lines
7.0 KiB
ReStructuredText
Support for external RAM
|
||
************************
|
||
|
||
.. toctree::
|
||
:maxdepth: 1
|
||
|
||
Introduction
|
||
============
|
||
|
||
The ESP32 has a few hundred KiB of internal RAM, residing on the same die as the rest of the ESP32. For some purposes, this is insufficient,
|
||
and therefore the ESP32 incorporates the ability to also use up to 4MiB of external SPI RAM memory as memory. The external memory is incorporated
|
||
in the memory map and is, within certain restrictions, usable in the same way internal data RAM is.
|
||
|
||
Hardware
|
||
========
|
||
|
||
The ESP32 supports SPI (P)SRAM connected in parallel with the SPI flash chip. While the ESP32 is capable of supporting several types
|
||
of RAM chips, the ESP32 SDK at the moment only supports the ESP-PSRAM32 chip.
|
||
|
||
The ESP-PSRAM32 chip is an 1.8V device, and can only be used in parallel with an 1.8V flash part. Make sure to either set the MTDI
|
||
pin to a high signal level on bootup, or program the fuses in the ESP32 to always use a VDD_SIO level of 1.8V. Not doing this risks
|
||
damaging the PSRAM and/or flash chip.
|
||
|
||
To connect the ESP-PSRAM chip to the ESP32D0W*, connect the following signals:
|
||
* PSRAM /CE (pin 1) - ESP32 GPIO 16
|
||
* PSRAM SO (pin 2) - flash DO
|
||
* PSRAM SIO[2] (pin 3) - flash WP
|
||
* PSRAM SI (pin 5) - flash DI
|
||
* PSRAM SCLK (pin 6) - ESP32 GPIO 17
|
||
* PSRAM SIO[3] (pin 7) - flash HOLD
|
||
* PSRAM Vcc (pin 8) - ESP32 VCC_SDIO
|
||
|
||
Connections for the ESP32D2W* chips are TBD.
|
||
|
||
.. NOTE::
|
||
Espressif sells an ESP-WROVER module which contains an ESP32, 1.8V flash and the ESP-PSRAM32 integrated in a module, ready for inclusion
|
||
on an end product PCB.
|
||
|
||
Software
|
||
========
|
||
|
||
ESP-IDF fully supports integrating external memory use into your applications. ESP-IDF can be configured to handle external RAM in several ways:
|
||
* Only initialize RAM. This allows the application to manually place data here by dereferencing pointers pointed at the external RAM memory
|
||
region (0x3F800000 and up).
|
||
* Initialize RAM and add it to the capability allocator. This allows a program to specifically allocate a chunk of external RAM using
|
||
``heap_caps_malloc(size, MALLOC_CAP_SPIRAM)``. This memory can be used and subsequently freed using a normal ``free()`` call.
|
||
* Initialize RAM, add it to the capability allocator and add memory to the pool of RAM that can be returned by ``malloc()``. This allows
|
||
any application to use the external RAM without having to rewrite the code to use ``heap_caps_malloc``.
|
||
* Initialize RAM, use a region start from 0x3F800000 for storing zero initialized data(BSS segment) of lwip,net802.11,pp,bluedroid library
|
||
by enabling :ref: `CONFIG_SPIRAM_ALLOW_BSS_SEG_EXTERNAL_MEMORY` in menuconfig, this way can save some internal memory，because the BSS segment
|
||
originally stored in internal memory，and the rest of external RAM can be add the capability allocator and add memory to the pool of RAM as above way
|
||
|
||
All these options can be selected from the menuconfig menu.
|
||
|
||
Restrictions
|
||
------------
|
||
|
||
The use of external RAM has a few restrictions:
|
||
* When disabling flash cache (for example, because the flash is being written to), the external RAM also becomes inaccessible; any reads from or
|
||
writes to it will lead to an illegal cache access exception. This is also the reason that ESP-IDF will never allocate a tasks stack in external
|
||
RAM.
|
||
* External RAM cannot be used as a place to store DMA transaction descriptors or as a buffer for a DMA transfer to read from or write into. Any
|
||
buffers that will be used in combination with DMA must be allocated using ``heap_caps_malloc(size, MALLOC_CAP_DMA)`` (and can be freed using a
|
||
standard ``free()`` call.)
|
||
* External RAM uses the same cache region as the external flash. This means that often accessed variables in external RAM can be read and
|
||
modified almost as quickly as in internal ram. However, when accessing large chunks of data (>32K), the cache can be insufficient and speeds
|
||
will fall back to the access speed of the external RAM. Moreover, accessing large chunks of data can 'push out' cached flash, possibly making
|
||
execution of code afterwards slower.
|
||
* External RAM cannot be used as task stack memory; because of this, xTaskCreate and similar functions will always allocate internal memory
|
||
for stack and task TCBs and xTaskCreateStatic-type functions will check if the buffers passed are internal. However, for tasks not calling
|
||
on code in ROM in any way, directly or indirectly, the menuconfig option :ref:`CONFIG_SPIRAM_ALLOW_STACK_EXTERNAL_MEMORY` will eliminate
|
||
the check in xTaskCreateStatic, allowing task stack in external RAM. Using this is not advised, however.
|
||
* External RAM initialized failed can not be ignored if enabled :ref:`CONFIG_SPIRAM_ALLOW_BSS_SEG_EXTERNAL_MEMORY`; because of this, some BSS segment
|
||
can not be placed into external memory if PSRAM can't work normally and can not be moved to internal memory at runtime because the address of
|
||
them is defined by linkfile, the :ref:`CONFIG_SPIRAM_IGNORE_NOTFOUND` can't handle this situation,if you want to enable :ref:
|
||
`CONFIG_SPIRAM_ALLOW_BSS_SEG_EXTERNAL_MEMORY` the :ref:`CONFIG_SPIRAM_IGNORE_NOTFOUND` will be disabled, and if initialize SPIRAM failed,the system
|
||
will invoke abort.
|
||
* External RAM of 4MBit (test up to know) has to be used with one of HSPI/VSPI occupied under 80MHz. Select which SPI host to be used by :ref:`CONFIG_SPIRAM_OCCUPY_SPI_HOST`.
|
||
|
||
Because there are a fair few situations that have a specific need for internal memory, but it is also possible to use malloc() to exhaust
|
||
internal memory, there is a pool reserved specifically for requests that cannot be resolved from external memory; allocating task
|
||
stack, DMA buffers and memory that stays accessible when cache is disabled is drawn from this pool. The size of this pool is configurable
|
||
in menuconfig.
|
||
|
||
|
||
Chip revisions
|
||
==============
|
||
|
||
There are some issues with certain revisions of the ESP32 that have repercussions for use with external RAM. These are documented in the ESP32
|
||
ECO_ document. In particular, ESP-IDF handles the bugs mentioned in the following ways:
|
||
|
||
ESP32 rev v0
|
||
------------
|
||
ESP-IDF has no workaround for the bugs in this revision of silicon, and it cannot be used to map external PSRAM into the ESP32s main memory map.
|
||
|
||
ESP32 rev v1
|
||
------------
|
||
The bugs in this silicon revision introduce a hazard when certain sequences of machine instructions operate on external memory locations (ESP32 ECO 3.2).
|
||
To work around this, the gcc compiler to compile ESP-IDF has been expanded with a flag: ``-mfix-esp32-psram-cache-issue``. With this flag passed to gcc
|
||
on the command line, the compiler works around these sequences and only outputs code that can safely be executed.
|
||
|
||
In ESP-IDF, this flag is enabled when you select :ref:`CONFIG_SPIRAM_CACHE_WORKAROUND`. ESP-IDF also takes other measures to make
|
||
sure no combination of PSRAM access plus the offending instruction sets are used: it links to a version of Newlib recompiled with the gcc flag, doesn't use
|
||
some ROM functions and allocates static memory for the WiFi stack.
|
||
|
||
.. _ECO: https://www.espressif.com/sites/default/files/documentation/eco_and_workarounds_for_bugs_in_esp32_en.pdf
|
||
|
||
|
||
|
||
|
||
|
||
|