mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
ba31aab2f4
Add new module variants for ESP32-DevKitM-1 and ESP32-PICO-DevKitM-02 boards Replace Ordering Information globally
228 lines
10 KiB
ReStructuredText
228 lines
10 KiB
ReStructuredText
=====================
|
|
ESP32-S2-DevKitM-1(U)
|
|
=====================
|
|
|
|
:link_to_translation:`zh_CN:[中文]`
|
|
|
|
This user guide provides information on Espressif's small-sized development board ESP32-S2-DevKitM-1(U).
|
|
|
|
ESP32-S2-DevKitM-1(U) is a general-purpose development board based on `ESP32-S2FH4 <https://www.espressif.com/sites/default/files/documentation/esp32-s2_datasheet_en.pdf>`__ chip, which falls into ESP32-S2 chip family. With a rich peripheral set and optimized pinout, this board allows rapid prototyping.
|
|
|
|
ESP32-S2-DevKitM-1 is embedded with `ESP32-S2-MINI-1 <https://www.espressif.com/sites/default/files/documentation/esp32-s2-mini-1_esp32-s2-mini-1u_datasheet_en.pdf>`__ module (on-board PCB antenna), while ESP32-S2-DevKitM-1U with `ESP32-S2-MINI-1U <https://www.espressif.com/sites/default/files/documentation/esp32-s2-mini-1_esp32-s2-mini-1u_datasheet_en.pdf>`__ module (U.FL connector to support external IPEX antenna).
|
|
|
|
+----------------------+-----------------------+
|
|
| |ESP32-S2-DevKitM-1| | |ESP32-S2-DevKitM-1U| |
|
|
+----------------------+-----------------------+
|
|
| ESP32-S2-DevKitM-1 | ESP32-S2-DevKitM-1U |
|
|
+----------------------+-----------------------+
|
|
|
|
.. |ESP32-S2-DevKitM-1| image:: ../../../_static/esp32-s2-devkitm-1-v1-isometric.png
|
|
|
|
.. |ESP32-S2-DevKitM-1U| image:: ../../../_static/esp32-s2-devkitm-1u-v1-isometric.png
|
|
|
|
The document consists of the following major sections:
|
|
|
|
- `Getting started`_: Provides an overview of the ESP32-S2-DevKitM-1(U) and hardware/software setup instructions to get started.
|
|
- `Hardware reference`_: Provides more detailed information about the ESP32-S2-DevKitM-1(U)'s hardware.
|
|
- `Related Documents`_: Gives links to related documentation.
|
|
|
|
Getting Started
|
|
===============
|
|
|
|
This section describes how to get started with ESP32-S2-DevKitM-1(U). It begins with a few introductory sections about the ESP32-S2-DevKitM-1(U), then Section `Start Application Development`_ provides instructions on how to get the ESP32-S2-DevKitM-1(U) ready and flash firmware into it.
|
|
|
|
Overview
|
|
--------
|
|
|
|
ESP32-S2-DevKitM-1(U) is entry-level development board equipped with either ESP32-S2-MINI-1 or ESP32-S2-MINI-1U module. Most of the I/O pins on the module are broken out to the pin headers on both sides for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S2-DevKitM-1(U) on a breadboard.
|
|
|
|
Contents and Packaging
|
|
----------------------
|
|
|
|
Retail orders
|
|
^^^^^^^^^^^^^
|
|
|
|
If you order a few samples, each ESP32-S2-DevKitM-1(U) comes in an individual package in either antistatic bag or any packaging depending on your retailer.
|
|
|
|
For retail orders, please go to https://www.espressif.com/en/company/contact/buy-a-sample.
|
|
|
|
|
|
Wholesale Orders
|
|
^^^^^^^^^^^^^^^^
|
|
|
|
If you order in bulk, the boards come in large cardboard boxes.
|
|
|
|
For wholesale orders, please go to https://www.espressif.com/en/contact-us/sales-questions.
|
|
|
|
Description of Components
|
|
-------------------------
|
|
|
|
.. _user-guide-devkitm-1-v1-board-front:
|
|
|
|
.. figure:: ../../../_static/esp32-s2-devkitm-1-v1-annotated-photo.png
|
|
:align: center
|
|
:alt: ESP32-S2-DevKitM-1 - front
|
|
:figclass: align-center
|
|
|
|
ESP32-S2-DevKitM-1 - front
|
|
|
|
.. figure:: ../../../_static/esp32-s2-devkitm-1u-v1-annotated-photo.png
|
|
:align: center
|
|
:alt: ESP32-S2-DevKitM-1U - front
|
|
:figclass: align-center
|
|
|
|
ESP32-S2-DevKitM-1U - front
|
|
|
|
.. list-table::
|
|
:widths: 30 70
|
|
:header-rows: 1
|
|
|
|
* - Key Component
|
|
- Description
|
|
* - ESP32-S2-MINI-1 or ESP32-S2-MINI-1U
|
|
- ESP32-S2-MINI-1 and ESP32-S2-MINI-1U are two powerful, generic Wi-Fi MCU modules that integrate ESP32-S2FH4 chip. ESP32-S2-MINI-1 comes with a PCB antenna, and ESP32-S2-MINI-1U with a U.FL connector for external IPEX antenna. They both feature a 4 MB external SPI flash.
|
|
* - 3.3 V Power On LED
|
|
- Turns on when the USB power is connected to the board.
|
|
* - USB to UART Bridge
|
|
- Single USB-UART bridge chip provides transfer rates up to 3 Mbps.
|
|
* - I/O Connector
|
|
- All available GPIO pins (except for the SPI bus for flash) are broken out to the pin headers on the board. Users can program ESP32-S2FH4 chip to enable multiple functions such as SPI, I2S, UART, I2C, touch sensors, PWM etc. For details, please see :ref:`user-guide-devkitm-1-v1-header-blocks`.
|
|
* - Reset Button
|
|
- Reset button.
|
|
* - Micro-USB Port
|
|
- USB interface. Power supply for the board as well as the communication interface between a computer and the ESP32-S2FH4 chip.
|
|
* - Boot Button
|
|
- Download button. Holding down **Boot** and then pressing **Reset** initiates Firmware Download mode for downloading firmware through the serial port.
|
|
* - RGB LED
|
|
- Addressable RGB LED (WS2812), driven by GPIO18.
|
|
* - 5 V to 3.3 V LDO
|
|
- Power regulator that converts a 5 V supply into a 3.3 V output.
|
|
* - U.FL Connector
|
|
- On **ESP32-S2-MINI-1U** module only. Connects to an external IPEX antenna.
|
|
|
|
|
|
Start Application Development
|
|
-----------------------------
|
|
|
|
Before powering up your ESP32-S2-DevKitM-1(U), please make sure that it is in good condition with no obvious signs of damage.
|
|
|
|
Required Hardware
|
|
^^^^^^^^^^^^^^^^^
|
|
|
|
- ESP32-S2-DevKitM-1(U)
|
|
|
|
+ For ESP32-S2-DevKitM-1U, an IPEX antenna is also required.
|
|
|
|
- USB 2.0 cable (Standard-A to Micro-B)
|
|
- Computer running Windows, Linux, or macOS
|
|
|
|
Software Setup
|
|
^^^^^^^^^^^^^^
|
|
|
|
Please proceed to :doc:`../../get-started/index`, where Section :ref:`get-started-step-by-step` will quickly help you set up the development environment and then flash an application example into your ESP32-S2-DevKitM-1(U).
|
|
|
|
.. note::
|
|
|
|
ESP32-S2 family chip only is only supported in ESP-IDF master or version v4.2 and higher.
|
|
|
|
Hardware Reference
|
|
==================
|
|
|
|
Block Diagram
|
|
-------------
|
|
|
|
A block diagram below shows the components of ESP32-S2-DevKitM-1 and their interconnections.
|
|
|
|
.. figure:: ../../../_static/esp32-s2-devkitm-1-v1-block-diagram.png
|
|
:align: center
|
|
:scale: 70%
|
|
:alt: ESP32-S2-DevKitM-1(U) (click to enlarge)
|
|
:figclass: align-center
|
|
|
|
ESP32-S2-DevKitM-1(U) (click to enlarge)
|
|
|
|
Power Supply Options
|
|
^^^^^^^^^^^^^^^^^^^^
|
|
|
|
There are three mutually exclusive ways to provide power to the board:
|
|
|
|
- Micro USB port, default power supply
|
|
- 5V and GND header pins
|
|
- 3V3 and GND header pins
|
|
|
|
It is recommended to use the first option: micro USB port.
|
|
|
|
.. _user-guide-devkitm-1-v1-header-blocks:
|
|
|
|
Header Block
|
|
------------
|
|
|
|
The two tables below provide the **Name** and **Function** of I/O header pins on both sides of the board, as shown in :ref:`user-guide-devkitm-1-v1-board-front`. The numbering and names are the same as in the `ESP32-S2-DevKitM-1(U) Schematics <https://dl.espressif.com/dl/schematics/ESP32-S2-DevKitM-1_V1_Schematics.pdf>`_ (PDF).
|
|
|
|
J1
|
|
^^^
|
|
=== ==== ===== ========================================================
|
|
No. Name Type Function
|
|
=== ==== ===== ========================================================
|
|
1 3V3 P 3.3 V power supply
|
|
2 0 I/O/T RTC_GPIO0, GPIO0
|
|
3 1 I/O/T RTC_GPIO1, GPIO1, TOUCH1, ADC1_CH0
|
|
4 2 I/O/T RTC_GPIO2, GPIO2, TOUCH2, ADC1_CH1
|
|
5 3 I/O/T RTC_GPIO3, GPIO3, TOUCH3, ADC1_CH2
|
|
6 4 I/O/T RTC_GPIO4, GPIO4, TOUCH4, ADC1_CH3
|
|
7 5 I/O/T RTC_GPIO5, GPIO5, TOUCH5, ADC1_CH4
|
|
8 6 I/O/T RTC_GPIO6, GPIO6, TOUCH6, ADC1_CH5
|
|
9 7 I/O/T RTC_GPIO7, GPIO7, TOUCH7, ADC1_CH6
|
|
10 8 I/O/T RTC_GPIO8, GPIO8, TOUCH8, ADC1_CH7
|
|
11 9 I/O/T RTC_GPIO9, GPIO9, TOUCH9, ADC1_CH8, FSPIHD
|
|
12 10 I/O/T RTC_GPIO10, GPIO10, TOUCH10, ADC1_CH9, FSPICS0, FSPIIO4
|
|
13 11 I/O/T RTC_GPIO11, GPIO11, TOUCH11, ADC2_CH0, FSPID, FSPIIO5
|
|
14 12 I/O/T RTC_GPIO12, GPIO12, TOUCH12, ADC2_CH1, FSPICLK, FSPIIO6
|
|
15 13 I/O/T RTC_GPIO13, GPIO13, TOUCH13, ADC2_CH2, FSPIQ, FSPIIO7
|
|
16 14 I/O/T RTC_GPIO14, GPIO14, TOUCH14, ADC2_CH3, FSPIWP, FSPIDQS
|
|
17 15 I/O/T RTC_GPIO15, GPIO15, U0RTS, ADC2_CH4, XTAL_32K_P
|
|
18 16 I/O/T RTC_GPIO16, GPIO16, U0CTS, ADC2_CH5, XTAL_32K_N
|
|
19 17 I/O/T RTC_GPIO17, GPIO17, U1TXD, ADC2_CH6, DAC_1
|
|
20 5V P 5 V power supply
|
|
21 G G Ground
|
|
=== ==== ===== ========================================================
|
|
|
|
J3
|
|
^^^
|
|
=== ==== ===== ========================================================
|
|
No. Name Type Function
|
|
=== ==== ===== ========================================================
|
|
1 G G Ground
|
|
2 RST I CHIP_PU
|
|
3 46 I GPIO46
|
|
4 45 I/O/T GPIO45
|
|
5 RX I/O/T U0RXD, GPIO44, CLK_OUT2
|
|
6 TX I/O/T U0TXD, GPIO43, CLK_OUT1
|
|
7 42 I/O/T MTMS, GPIO42
|
|
8 41 I/O/T MTDI, GPIO41, CLK_OUT1
|
|
9 40 I/O/T MTDO, GPIO40, CLK_OUT2
|
|
10 39 I/O/T MTCK, GPIO39, CLK_OUT3
|
|
11 38 I/O/T GPIO38, FSPIWP
|
|
12 37 I/O/T SPIDQS, GPIO37, FSPIQ
|
|
13 36 I/O/T SPIIO7, GPIO36, FSPICLK
|
|
14 35 I/O/T SPIIO6, GPIO35, FSPID
|
|
15 34 I/O/T SPIIO5, GPIO34, FSPICS0
|
|
16 33 I/O/T SPIIO4, GPIO33, FSPIHD
|
|
17 26 I/O/T SPICS1, GPIO26
|
|
18 21 I/O/T RTC_GPIO21, GPIO21
|
|
19 20 I/O/T RTC_GPIO20, GPIO20, U1CTS, ADC2_CH9, CLK_OUT1, USB_D+
|
|
20 19 I/O/T RTC_GPIO19, GPIO19, U1RTS, ADC2_CH8, CLK_OUT2, USB_D-
|
|
21 18 I/O/T RTC_GPIO18, GPIO18, U1RXD, ADC2_CH7, DAC_2, CLK_OUT3
|
|
=== ==== ===== ========================================================
|
|
|
|
Related Documents
|
|
=================
|
|
* `ESP32-S2-DevKitM-1(U) Schematics <https://dl.espressif.com/dl/schematics/ESP32-S2-DevKitM-1_V1_Schematics.pdf>`_ (PDF)
|
|
* `ESP32-S2-DevKitM-1(U) PCB Layout <https://dl.espressif.com/dl/schematics/ESP32-S2-DevKitM-1_V1_PCB_Layout.pdf>`_ (PDF)
|
|
* `ESP32-S2-DevKitM-1(U) Dimensions <https://dl.espressif.com/dl/schematics/ESP32-S2-DevKitM-1_V1_Dimensions.pdf>`_ (PDF)
|
|
* `ESP32-S2 Family Datasheet <https://www.espressif.com/sites/default/files/documentation/esp32-s2_datasheet_en.pdf>`_ (PDF)
|
|
* `ESP32-S2-MINI-1 & ESP32-S2-MINI-1U Datasheet <https://www.espressif.com/sites/default/files/documentation/esp32-s2-mini-1_esp32-s2-mini-1u_datasheet_en.pdf>`_ (PDF)
|
|
* `ESP Product Selector <https://products.espressif.com/#/product-selector?names=>`_
|
|
|
|
For other design documentation for the board, please contact us at sales@espressif.com.
|