esp-idf/examples/bluetooth/bluedroid/ble/ble_ibeacon
2022-07-11 09:49:09 +05:30
..
main components/bt: Update licenses 2021-12-08 10:59:06 +08:00
CMakeLists.txt tools: Increase the minimal supported CMake version to 3.16 2022-06-01 06:35:02 +00:00
README.md Added ESP32-S3 in README Bluedroid examples 2022-07-11 09:49:09 +05:30
sdkconfig.defaults examples: fix sdkconfig warnings 2019-11-21 15:36:06 +01:00
sdkconfig.defaults.esp32 spi_flash: Remove legacy spi_flash drivers 2022-07-01 11:01:34 +08:00
sdkconfig.defaults.esp32c2 sdkconfig default for the esp32c2 2022-07-08 04:52:47 +00:00
sdkconfig.defaults.esp32c3 spi_flash: Remove legacy spi_flash drivers 2022-07-01 11:01:34 +08:00
sdkconfig.defaults.esp32h2 sdkconfig default for the esp32c2 2022-07-08 04:52:47 +00:00
sdkconfig.defaults.esp32s3 spi_flash: Remove legacy spi_flash drivers 2022-07-01 11:01:34 +08:00

Supported Targets ESP32 ESP32-C3 ESP32-H2 ESP32-C2 ESP32-S3

ESP-IDF iBeacon demo

From welcoming people as they arrive at a sporting event to providing information about a nearby museum exhibit, iBeacon opens a new world of possibilities for location awareness, and countless opportunities for interactivity between iOS devices and iBeacon hardware.

How to Use Example

Before project configuration and build, be sure to set the correct chip target using:

idf.py set-target <chip_name>

Note: iBeacon is a trademark of Apple Inc.

Before building devices which use iBeacon technology, visit Apple iBeacon to obtain a license.

iBeacon Mode

This example demonstrates iBeacon-compatible BLE advertising, and scanning of iBeacons:

  • IBEACON_SENDER: demo to send iBeacon-compatible advertising data.

  • IBEACON_RECEIVER: demo to receive and resolve iBeacon advertising data.

Which demo will be run depends on the menuconfig, developers can set it in iBeacon Example Configuration.

The default mode is iBeacon Sender.

Configure the project

Open the project configuration menu:

idf.py menuconfig

And then enter Component config --> Bluetooth --> Bluedroid Enable

Because the number of peripherals may be very large, developers can enable the BLE Scan Duplicate Options, the maximum number of devices in scan duplicate filter depends on the free heap size, when the cache is full, it is cleared.

Event Processing

In the iBeacon receiver demo, the scan result will be posted to ESP_GAP_SEARCH_INQ_RES_EVT event:

switch (scan_result->scan_rst.search_evt) {
    case ESP_GAP_SEARCH_INQ_RES_EVT:
    /* Search for BLE iBeacon Packet */
    ......
    break;
    default:
    break;
}

Build and Flash

Run idf.py -p PORT flash monitor to build, flash and monitor the project.

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

The iBeacon sender will broadcast iBeacon packet after initializing the Bluetooth protocol stack, and the iBeacon receiver will scan the iBeacon packet.

iBeacon Sender

I (384) boot: Loaded app from partition at offset 0x10000
I (384) boot: Disabling RNG early entropy source...
I (386) cpu_start: Pro cpu up.
I (389) cpu_start: Starting app cpu, entry point is 0x40081010
I (0) cpu_start: App cpu up.
I (400) heap_init: Initializing. RAM available for dynamic allocation:
I (406) heap_init: At 3FFAFF10 len 000000F0 (0 KiB): DRAM
I (413) heap_init: At 3FFCCCA8 len 00013358 (76 KiB): DRAM
I (419) heap_init: At 3FFE0440 len 00003BC0 (14 KiB): D/IRAM
I (425) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM
I (431) heap_init: At 40090E58 len 0000F1A8 (60 KiB): IRAM
I (438) cpu_start: Pro cpu start user code
I (120) cpu_start: Starting scheduler on PRO CPU
I (0) cpu_start: Starting scheduler on APP CPU
I (244) BTDM_INIT: BT controller compile version [44d04c1]

I (244) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE
I (624) phy: phy_version: 3910, c0c45a3, May 21 2018, 18:07:06, 0, 0
I (654) IBEACON_DEMO: register callback

iBeacon Receiver

I (384) boot: Loaded app from partition at offset 0x10000
I (384) boot: Disabling RNG early entropy source...
I (385) cpu_start: Pro cpu up.\0x1b[0m
I (389) cpu_start: Starting app cpu, entry point is 0x40081010
I (0) cpu_start: App cpu up.
I (400) heap_init: Initializing. RAM available for dynamic allocation:
I (406) heap_init: At 3FFAFF10 len 000000F0 (0 KiB): DRAM
I (412) heap_init: At 3FFCCC88 len 00013378 (76 KiB): DRAM
I (418) heap_init: At 3FFE0440 len 00003BC0 (14 KiB): D/IRAM
I (425) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM
I (431) heap_init: At 40090E58 len 0000F1A8 (60 KiB): IRAM
I (437) cpu_start: Pro cpu start user code\0x1b[0m
I (120) cpu_start: Starting scheduler on PRO CPU.
I (0) cpu_start: Starting scheduler on APP CPU.
I (243) BTDM_INIT: BT controller compile version [44d04c1]

I (243) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE
I (633) phy: phy_version: 3910, c0c45a3, May 21 2018, 18:07:06, 0, 0
I (663) IBEACON_DEMO: register callback
I (329203) IBEACON_DEMO: ----------iBeacon Found----------
I (329203) IBEACON_DEMO: Device address:: 30 ae a4 00 42 82
I (329203) IBEACON_DEMO: Proximity UUID:: fd a5 06 93 a4 e2 4f b1 af cf c6 eb 07 64 78 25

Troubleshooting

For any technical queries, please open an issue on GitHub. We will get back to you soon.