esp-idf/components/driver/rtc_module.c
2016-12-16 14:30:27 +08:00

673 lines
31 KiB
C

// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
#include <esp_types.h>
#include <stdlib.h>
#include <ctype.h>
#include "rom/ets_sys.h"
#include "esp_log.h"
#include "soc/rtc_io_reg.h"
#include "soc/sens_reg.h"
#include "soc/rtc_cntl_reg.h"
#include "rtc_io.h"
#include "touch_pad.h"
#include "adc.h"
#include "dac.h"
#include "freertos/FreeRTOS.h"
#include "freertos/xtensa_api.h"
static const char *RTC_MODULE_TAG = "RTC_MODULE";
#define RTC_MODULE_CHECK(a, str, ret_val) if (!(a)) { \
ESP_LOGE(RTC_MODULE_TAG,"%s:%d (%s):%s", __FILE__, __LINE__, __FUNCTION__, str); \
return (ret_val); \
}
#define ADC1_CHECK_FUNCTION_RET(fun_ret) if(fun_ret!=ESP_OK){\
ESP_LOGE(RTC_MODULE_TAG,"%s:%d\n",__FUNCTION__,__LINE__);\
return ESP_FAIL;\
}
portMUX_TYPE rtc_spinlock = portMUX_INITIALIZER_UNLOCKED;
//Reg,Mux,Fun,IE,Up,Down,Rtc_number
const rtc_gpio_desc_t rtc_gpio_desc[GPIO_PIN_COUNT] = {
{RTC_IO_TOUCH_PAD1_REG, RTC_IO_TOUCH_PAD1_MUX_SEL_M, RTC_IO_TOUCH_PAD1_FUN_SEL_S, RTC_IO_TOUCH_PAD1_FUN_IE_M, RTC_IO_TOUCH_PAD1_RUE_M, RTC_IO_TOUCH_PAD1_RDE_M, RTC_IO_TOUCH_PAD1_SLP_SEL_M, RTC_IO_TOUCH_PAD1_SLP_IE_M, RTC_CNTL_TOUCH_PAD1_HOLD_FORCE_M, 11}, //0
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //1
{RTC_IO_TOUCH_PAD2_REG, RTC_IO_TOUCH_PAD2_MUX_SEL_M, RTC_IO_TOUCH_PAD2_FUN_SEL_S, RTC_IO_TOUCH_PAD2_FUN_IE_M, RTC_IO_TOUCH_PAD2_RUE_M, RTC_IO_TOUCH_PAD2_RDE_M, RTC_IO_TOUCH_PAD2_SLP_SEL_M, RTC_IO_TOUCH_PAD2_SLP_IE_M, RTC_CNTL_TOUCH_PAD2_HOLD_FORCE_M, 12}, //2
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //3
{RTC_IO_TOUCH_PAD0_REG, RTC_IO_TOUCH_PAD0_MUX_SEL_M, RTC_IO_TOUCH_PAD0_FUN_SEL_S, RTC_IO_TOUCH_PAD0_FUN_IE_M, RTC_IO_TOUCH_PAD0_RUE_M, RTC_IO_TOUCH_PAD0_RDE_M, RTC_IO_TOUCH_PAD0_SLP_SEL_M, RTC_IO_TOUCH_PAD0_SLP_IE_M, RTC_CNTL_TOUCH_PAD0_HOLD_FORCE_M, 10}, //4
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //5
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //6
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //7
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //8
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //9
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //10
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //11
{RTC_IO_TOUCH_PAD5_REG, RTC_IO_TOUCH_PAD5_MUX_SEL_M, RTC_IO_TOUCH_PAD5_FUN_SEL_S, RTC_IO_TOUCH_PAD5_FUN_IE_M, RTC_IO_TOUCH_PAD5_RUE_M, RTC_IO_TOUCH_PAD5_RDE_M, RTC_IO_TOUCH_PAD5_SLP_SEL_M, RTC_IO_TOUCH_PAD5_SLP_IE_M, RTC_CNTL_TOUCH_PAD5_HOLD_FORCE_M, 15}, //12
{RTC_IO_TOUCH_PAD4_REG, RTC_IO_TOUCH_PAD4_MUX_SEL_M, RTC_IO_TOUCH_PAD4_FUN_SEL_S, RTC_IO_TOUCH_PAD4_FUN_IE_M, RTC_IO_TOUCH_PAD4_RUE_M, RTC_IO_TOUCH_PAD4_RDE_M, RTC_IO_TOUCH_PAD4_SLP_SEL_M, RTC_IO_TOUCH_PAD4_SLP_IE_M, RTC_CNTL_TOUCH_PAD4_HOLD_FORCE_M, 14}, //13
{RTC_IO_TOUCH_PAD6_REG, RTC_IO_TOUCH_PAD6_MUX_SEL_M, RTC_IO_TOUCH_PAD6_FUN_SEL_S, RTC_IO_TOUCH_PAD6_FUN_IE_M, RTC_IO_TOUCH_PAD6_RUE_M, RTC_IO_TOUCH_PAD6_RDE_M, RTC_IO_TOUCH_PAD6_SLP_SEL_M, RTC_IO_TOUCH_PAD6_SLP_IE_M, RTC_CNTL_TOUCH_PAD6_HOLD_FORCE_M, 16}, //14
{RTC_IO_TOUCH_PAD3_REG, RTC_IO_TOUCH_PAD3_MUX_SEL_M, RTC_IO_TOUCH_PAD3_FUN_SEL_S, RTC_IO_TOUCH_PAD3_FUN_IE_M, RTC_IO_TOUCH_PAD3_RUE_M, RTC_IO_TOUCH_PAD3_RDE_M, RTC_IO_TOUCH_PAD3_SLP_SEL_M, RTC_IO_TOUCH_PAD3_SLP_IE_M, RTC_CNTL_TOUCH_PAD3_HOLD_FORCE_M, 13}, //15
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //16
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //17
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //18
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //19
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //20
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //21
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //22
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //23
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //24
{RTC_IO_PAD_DAC1_REG, RTC_IO_PDAC1_MUX_SEL_M, RTC_IO_PDAC1_FUN_SEL_S, RTC_IO_PDAC1_FUN_IE_M, RTC_IO_PDAC1_RUE_M, RTC_IO_PDAC1_RDE_M, RTC_IO_PDAC1_SLP_SEL_M, RTC_IO_PDAC1_SLP_IE_M, RTC_CNTL_PDAC1_HOLD_FORCE_M, 6}, //25
{RTC_IO_PAD_DAC2_REG, RTC_IO_PDAC2_MUX_SEL_M, RTC_IO_PDAC2_FUN_SEL_S, RTC_IO_PDAC2_FUN_IE_M, RTC_IO_PDAC2_RUE_M, RTC_IO_PDAC2_RDE_M, RTC_IO_PDAC2_SLP_SEL_M, RTC_IO_PDAC2_SLP_IE_M, RTC_CNTL_PDAC1_HOLD_FORCE_M, 7}, //26
{RTC_IO_TOUCH_PAD7_REG, RTC_IO_TOUCH_PAD7_MUX_SEL_M, RTC_IO_TOUCH_PAD7_FUN_SEL_S, RTC_IO_TOUCH_PAD7_FUN_IE_M, RTC_IO_TOUCH_PAD7_RUE_M, RTC_IO_TOUCH_PAD7_RDE_M, RTC_IO_TOUCH_PAD7_SLP_SEL_M, RTC_IO_TOUCH_PAD7_SLP_IE_M, RTC_CNTL_TOUCH_PAD7_HOLD_FORCE_M, 17}, //27
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //28
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //29
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //30
{0, 0, 0, 0, 0, 0, 0, 0, 0, -1}, //31
{RTC_IO_XTAL_32K_PAD_REG, RTC_IO_X32P_MUX_SEL_M, RTC_IO_X32P_FUN_SEL_S, RTC_IO_X32P_FUN_IE_M, RTC_IO_X32P_RUE_M, RTC_IO_X32P_RDE_M, RTC_IO_X32P_SLP_SEL_M, RTC_IO_X32P_SLP_IE_M, RTC_CNTL_X32P_HOLD_FORCE_M, 9}, //32
{RTC_IO_XTAL_32K_PAD_REG, RTC_IO_X32N_MUX_SEL_M, RTC_IO_X32N_FUN_SEL_S, RTC_IO_X32N_FUN_IE_M, RTC_IO_X32N_RUE_M, RTC_IO_X32N_RDE_M, RTC_IO_X32N_SLP_SEL_M, RTC_IO_X32N_SLP_IE_M, RTC_CNTL_X32N_HOLD_FORCE_M, 8}, //33
{RTC_IO_ADC_PAD_REG, RTC_IO_ADC1_MUX_SEL_M, RTC_IO_ADC1_FUN_SEL_S, RTC_IO_ADC1_FUN_IE_M, 0, 0, RTC_IO_ADC1_SLP_SEL_M, RTC_IO_ADC1_SLP_IE_M, RTC_CNTL_ADC1_HOLD_FORCE_M, 4}, //34
{RTC_IO_ADC_PAD_REG, RTC_IO_ADC2_MUX_SEL_M, RTC_IO_ADC2_FUN_SEL_S, RTC_IO_ADC2_FUN_IE_M, 0, 0, RTC_IO_ADC2_SLP_SEL_M, RTC_IO_ADC2_SLP_IE_M, RTC_CNTL_ADC2_HOLD_FORCE_M, 5}, //35
{RTC_IO_SENSOR_PADS_REG, RTC_IO_SENSE1_MUX_SEL_M, RTC_IO_SENSE1_FUN_SEL_S, RTC_IO_SENSE1_FUN_IE_M, 0, 0, RTC_IO_SENSE1_SLP_SEL_M, RTC_IO_SENSE1_SLP_IE_M, RTC_CNTL_SENSE1_HOLD_FORCE_M, 0}, //36
{RTC_IO_SENSOR_PADS_REG, RTC_IO_SENSE2_MUX_SEL_M, RTC_IO_SENSE2_FUN_SEL_S, RTC_IO_SENSE2_FUN_IE_M, 0, 0, RTC_IO_SENSE2_SLP_SEL_M, RTC_IO_SENSE2_SLP_IE_M, RTC_CNTL_SENSE2_HOLD_FORCE_M, 1}, //37
{RTC_IO_SENSOR_PADS_REG, RTC_IO_SENSE3_MUX_SEL_M, RTC_IO_SENSE3_FUN_SEL_S, RTC_IO_SENSE3_FUN_IE_M, 0, 0, RTC_IO_SENSE3_SLP_SEL_M, RTC_IO_SENSE3_SLP_IE_M, RTC_CNTL_SENSE3_HOLD_FORCE_M, 2}, //38
{RTC_IO_SENSOR_PADS_REG, RTC_IO_SENSE4_MUX_SEL_M, RTC_IO_SENSE4_FUN_SEL_S, RTC_IO_SENSE4_FUN_IE_M, 0, 0, RTC_IO_SENSE4_SLP_SEL_M, RTC_IO_SENSE4_SLP_IE_M, RTC_CNTL_SENSE4_HOLD_FORCE_M, 3}, //39
};
/*---------------------------------------------------------------
RTC IO
---------------------------------------------------------------*/
esp_err_t rtc_gpio_init(gpio_num_t gpio_num)
{
RTC_MODULE_CHECK(RTC_GPIO_IS_VALID_GPIO(gpio_num), "RTC_GPIO number error", ESP_ERR_INVALID_ARG);
portENTER_CRITICAL(&rtc_spinlock);
// 0: GPIO connected to digital GPIO module. 1: GPIO connected to analog RTC module.
SET_PERI_REG_MASK(rtc_gpio_desc[gpio_num].reg, (rtc_gpio_desc[gpio_num].mux));
//0:RTC FUNCIOTN 1,2,3:Reserved
SET_PERI_REG_BITS(rtc_gpio_desc[gpio_num].reg, RTC_IO_TOUCH_PAD1_FUN_SEL_V, 0x0, rtc_gpio_desc[gpio_num].func);
portEXIT_CRITICAL(&rtc_spinlock);
return ESP_OK;
}
esp_err_t rtc_gpio_deinit(gpio_num_t gpio_num)
{
RTC_MODULE_CHECK(RTC_GPIO_IS_VALID_GPIO(gpio_num), "RTC_GPIO number error", ESP_ERR_INVALID_ARG);
portENTER_CRITICAL(&rtc_spinlock);
//Select Gpio as Digital Gpio
CLEAR_PERI_REG_MASK(rtc_gpio_desc[gpio_num].reg, (rtc_gpio_desc[gpio_num].mux));
portEXIT_CRITICAL(&rtc_spinlock);
return ESP_OK;
}
static esp_err_t rtc_gpio_output_enable(gpio_num_t gpio_num)
{
int rtc_gpio_num = rtc_gpio_desc[gpio_num].rtc_num;
RTC_MODULE_CHECK(rtc_gpio_num != -1, "RTC_GPIO number error", ESP_ERR_INVALID_ARG);
SET_PERI_REG_MASK(RTC_GPIO_ENABLE_W1TS_REG, (1 << (rtc_gpio_num + RTC_GPIO_ENABLE_W1TS_S)));
CLEAR_PERI_REG_MASK(RTC_GPIO_ENABLE_W1TC_REG, (1 << (rtc_gpio_num + RTC_GPIO_ENABLE_W1TC_S)));
return ESP_OK;
}
static esp_err_t rtc_gpio_output_disable(gpio_num_t gpio_num)
{
int rtc_gpio_num = rtc_gpio_desc[gpio_num].rtc_num;
RTC_MODULE_CHECK(rtc_gpio_num != -1, "RTC_GPIO number error", ESP_ERR_INVALID_ARG);
CLEAR_PERI_REG_MASK(RTC_GPIO_ENABLE_W1TS_REG, (1 << (rtc_gpio_num + RTC_GPIO_ENABLE_W1TS_S)));
SET_PERI_REG_MASK(RTC_GPIO_ENABLE_W1TC_REG, (1 << ( rtc_gpio_num + RTC_GPIO_ENABLE_W1TC_S)));
return ESP_OK;
}
static esp_err_t rtc_gpio_input_enable(gpio_num_t gpio_num)
{
RTC_MODULE_CHECK(RTC_GPIO_IS_VALID_GPIO(gpio_num), "RTC_GPIO number error", ESP_ERR_INVALID_ARG);
portENTER_CRITICAL(&rtc_spinlock);
SET_PERI_REG_MASK(rtc_gpio_desc[gpio_num].reg, rtc_gpio_desc[gpio_num].ie);
portEXIT_CRITICAL(&rtc_spinlock);
return ESP_OK;
}
static esp_err_t rtc_gpio_input_disable(gpio_num_t gpio_num)
{
RTC_MODULE_CHECK(RTC_GPIO_IS_VALID_GPIO(gpio_num), "RTC_GPIO number error", ESP_ERR_INVALID_ARG);
portENTER_CRITICAL(&rtc_spinlock);
CLEAR_PERI_REG_MASK(rtc_gpio_desc[gpio_num].reg, rtc_gpio_desc[gpio_num].ie);
portEXIT_CRITICAL(&rtc_spinlock);
return ESP_OK;
}
esp_err_t rtc_gpio_set_level(gpio_num_t gpio_num, uint32_t level)
{
int rtc_gpio_num = rtc_gpio_num = rtc_gpio_desc[gpio_num].rtc_num;;
RTC_MODULE_CHECK(RTC_GPIO_IS_VALID_GPIO(gpio_num), "RTC_GPIO number error", ESP_ERR_INVALID_ARG);
if (level) {
WRITE_PERI_REG(RTC_GPIO_OUT_W1TS_REG, (1 << (rtc_gpio_num + RTC_GPIO_OUT_DATA_W1TS_S)));
} else {
WRITE_PERI_REG(RTC_GPIO_OUT_W1TC_REG, (1 << (rtc_gpio_num + RTC_GPIO_OUT_DATA_W1TC_S)));
}
return ESP_OK;
}
uint32_t rtc_gpio_get_level(gpio_num_t gpio_num)
{
uint32_t level = 0;
int rtc_gpio_num = rtc_gpio_desc[gpio_num].rtc_num;
RTC_MODULE_CHECK(RTC_GPIO_IS_VALID_GPIO(gpio_num), "RTC_GPIO number error", ESP_ERR_INVALID_ARG);
portENTER_CRITICAL(&rtc_spinlock);
level = READ_PERI_REG(RTC_GPIO_IN_REG);
portEXIT_CRITICAL(&rtc_spinlock);
return ((level >> (RTC_GPIO_IN_NEXT_S + rtc_gpio_num)) & 0x01);
}
esp_err_t rtc_gpio_set_direction(gpio_num_t gpio_num, rtc_gpio_mode_t mode)
{
RTC_MODULE_CHECK(RTC_GPIO_IS_VALID_GPIO(gpio_num), "RTC_GPIO number error", ESP_ERR_INVALID_ARG);
switch (mode) {
case RTC_GPIO_MODE_INPUT_ONLY:
rtc_gpio_output_disable(gpio_num);
rtc_gpio_input_enable(gpio_num);
break;
case RTC_GPIO_MODE_OUTPUT_ONLY:
rtc_gpio_output_enable(gpio_num);
rtc_gpio_input_disable(gpio_num);
break;
case RTC_GPIO_MODE_INPUT_OUTUT:
rtc_gpio_output_enable(gpio_num);
rtc_gpio_input_enable(gpio_num);
break;
case RTC_GPIO_MODE_DISABLED:
rtc_gpio_output_disable(gpio_num);
rtc_gpio_input_disable(gpio_num);
break;
}
return ESP_OK;
}
esp_err_t rtc_gpio_pullup_en(gpio_num_t gpio_num)
{
//this is a digital pad
if (rtc_gpio_desc[gpio_num].pullup == 0) {
return ESP_FAIL;
}
//this is a rtc pad
portENTER_CRITICAL(&rtc_spinlock);
SET_PERI_REG_MASK(rtc_gpio_desc[gpio_num].reg, rtc_gpio_desc[gpio_num].pullup);
portEXIT_CRITICAL(&rtc_spinlock);
return ESP_OK;
}
esp_err_t rtc_gpio_pulldown_en(gpio_num_t gpio_num)
{
//this is a digital pad
if (rtc_gpio_desc[gpio_num].pulldown == 0) {
return ESP_FAIL;
}
//this is a rtc pad
portENTER_CRITICAL(&rtc_spinlock);
SET_PERI_REG_MASK(rtc_gpio_desc[gpio_num].reg, rtc_gpio_desc[gpio_num].pulldown);
portEXIT_CRITICAL(&rtc_spinlock);
return ESP_OK;
}
esp_err_t rtc_gpio_pullup_dis(gpio_num_t gpio_num)
{
//this is a digital pad
if ( rtc_gpio_desc[gpio_num].pullup == 0 ) {
return ESP_FAIL;
}
//this is a rtc pad
portENTER_CRITICAL(&rtc_spinlock);
CLEAR_PERI_REG_MASK(rtc_gpio_desc[gpio_num].reg, rtc_gpio_desc[gpio_num].pullup);
portEXIT_CRITICAL(&rtc_spinlock);
return ESP_OK;
}
esp_err_t rtc_gpio_pulldown_dis(gpio_num_t gpio_num)
{
//this is a digital pad
if (rtc_gpio_desc[gpio_num].pulldown == 0) {
return ESP_FAIL;
}
//this is a rtc pad
portENTER_CRITICAL(&rtc_spinlock);
CLEAR_PERI_REG_MASK(rtc_gpio_desc[gpio_num].reg, rtc_gpio_desc[gpio_num].pulldown);
portEXIT_CRITICAL(&rtc_spinlock);
return ESP_OK;
}
void rtc_gpio_unhold_all()
{
for (int gpio = 0; gpio < GPIO_PIN_COUNT; ++gpio) {
const rtc_gpio_desc_t* desc = &rtc_gpio_desc[gpio];
if (desc->hold != 0) {
REG_CLR_BIT(RTC_CNTL_HOLD_FORCE_REG, desc->hold);
}
}
}
/*---------------------------------------------------------------
Touch Pad
---------------------------------------------------------------*/
esp_err_t touch_pad_isr_handler_register(void(*fn)(void *), void *arg, int intr_alloc_flags, touch_isr_handle_t *handle)
{
RTC_MODULE_CHECK(fn, "Touch_Pad ISR null", ESP_ERR_INVALID_ARG);
return esp_intr_alloc(ETS_RTC_CORE_INTR_SOURCE, intr_alloc_flags, fn, arg, handle);
}
static esp_err_t touch_pad_get_io_num(touch_pad_t touch_num, gpio_num_t *gpio_num)
{
switch (touch_num) {
case TOUCH_PAD_NUM0:
*gpio_num = 4;
break;
case TOUCH_PAD_NUM1:
*gpio_num = 0;
break;
case TOUCH_PAD_NUM2:
*gpio_num = 2;
break;
case TOUCH_PAD_NUM3:
*gpio_num = 15;
break;
case TOUCH_PAD_NUM4:
*gpio_num = 13;
break;
case TOUCH_PAD_NUM5:
*gpio_num = 12;
break;
case TOUCH_PAD_NUM6:
*gpio_num = 14;
break;
case TOUCH_PAD_NUM7:
*gpio_num = 27;
break;
case TOUCH_PAD_NUM8:
*gpio_num = 33;
break;
case TOUCH_PAD_NUM9:
*gpio_num = 32;
break;
default:
return ESP_ERR_INVALID_ARG;
}
return ESP_OK;
}
static esp_err_t touch_pad_init_config(uint16_t sleep_cycle, uint16_t sample_cycle_num)
{
portENTER_CRITICAL(&rtc_spinlock);
SET_PERI_REG_BITS(RTC_IO_TOUCH_CFG_REG, RTC_IO_TOUCH_XPD_BIAS, 1, RTC_IO_TOUCH_XPD_BIAS_S);
SET_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_MEAS_EN_CLR);
//clear touch enable
WRITE_PERI_REG(SENS_SAR_TOUCH_ENABLE_REG, 0x0);
//enable Rtc Touch pad Timer
SET_PERI_REG_MASK(RTC_CNTL_STATE0_REG, RTC_CNTL_TOUCH_SLP_TIMER_EN);
//config pad module sleep time and sample num
//Touch pad SleepCycle Time = 150Khz
SET_PERI_REG_BITS(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_SLEEP_CYCLES, sleep_cycle, SENS_TOUCH_SLEEP_CYCLES_S);//150kHZ
//Touch Pad Measure Time= 8Mhz
SET_PERI_REG_BITS(SENS_SAR_TOUCH_CTRL1_REG, SENS_TOUCH_MEAS_DELAY, sample_cycle_num, SENS_TOUCH_MEAS_DELAY_S); //8Mhz
portEXIT_CRITICAL(&rtc_spinlock);
return ESP_OK;
}
void touch_pad_init()
{
touch_pad_init_config(TOUCH_PAD_SLEEP_CYCLE_CONFIG, TOUCH_PAD_MEASURE_CYCLE_CONFIG);
}
static void touch_pad_counter_init(touch_pad_t touch_num)
{
portENTER_CRITICAL(&rtc_spinlock);
//Enable Tie,Init Level(Counter)
SET_PERI_REG_MASK(RTC_IO_TOUCH_PAD0_REG + touch_num * 4, RTC_IO_TOUCH_PAD0_TIE_OPT_M);
//Touch Set Slop(Counter)
SET_PERI_REG_BITS(RTC_IO_TOUCH_PAD0_REG + touch_num * 4, RTC_IO_TOUCH_PAD0_DAC_V, 7, RTC_IO_TOUCH_PAD0_DAC_S);
//Enable Touch Pad IO
SET_PERI_REG_MASK(RTC_IO_TOUCH_PAD0_REG + touch_num * 4, RTC_IO_TOUCH_PAD0_START_M);
portEXIT_CRITICAL(&rtc_spinlock);
}
static void touch_pad_power_on(touch_pad_t touch_num)
{
portENTER_CRITICAL(&rtc_spinlock);
//Enable Touch Pad Power on
SET_PERI_REG_MASK(RTC_IO_TOUCH_PAD0_REG + touch_num * 4, RTC_IO_TOUCH_PAD0_XPD_M);
portEXIT_CRITICAL(&rtc_spinlock);
}
static void toch_pad_io_init(touch_pad_t touch_num)
{
gpio_num_t gpio_num = GPIO_NUM_0;
touch_pad_get_io_num(touch_num, &gpio_num);
rtc_gpio_init(gpio_num);
rtc_gpio_set_direction(gpio_num, RTC_GPIO_MODE_DISABLED);
rtc_gpio_pulldown_dis(gpio_num);
rtc_gpio_pullup_dis(gpio_num);
}
static esp_err_t touch_start(touch_pad_t touch_num)
{
RTC_MODULE_CHECK(touch_num < TOUCH_PAD_MAX, "Touch_Pad Num Err", ESP_ERR_INVALID_ARG);
portENTER_CRITICAL(&rtc_spinlock);
//Enable Digital rtc control :work mode and out mode
SET_PERI_REG_MASK(SENS_SAR_TOUCH_ENABLE_REG, (1 << (touch_num + SENS_TOUCH_PAD_WORKEN_S)) | \
(1 << (touch_num + SENS_TOUCH_PAD_OUTEN2_S)) | \
(1 << (touch_num + SENS_TOUCH_PAD_OUTEN1_S)));
portEXIT_CRITICAL(&rtc_spinlock);
return ESP_OK;
}
esp_err_t touch_pad_config(touch_pad_t touch_num, uint16_t threshold)
{
RTC_MODULE_CHECK(touch_num < TOUCH_PAD_MAX, "Touch_Pad Num Err", ESP_ERR_INVALID_ARG);
portENTER_CRITICAL(&rtc_spinlock);
//clear touch force ,select the Touch mode is Timer
CLEAR_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_START_EN_M);
CLEAR_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_START_FORCE_M);
//set threshold
uint8_t shift;
shift = (touch_num & 1) ? SENS_TOUCH_OUT_TH1_S : SENS_TOUCH_OUT_TH0_S;
SET_PERI_REG_BITS((SENS_SAR_TOUCH_THRES1_REG + (touch_num / 2) * 4), SENS_TOUCH_OUT_TH0, threshold, shift);
//When touch value < threshold ,the Intr will give
CLEAR_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL1_REG, SENS_TOUCH_OUT_SEL);
//Intr will give ,when SET0 < threshold
SET_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL1_REG, SENS_TOUCH_OUT_1EN);
//Enable Rtc Touch Module Intr,the Interrupt need Rtc out Enable
SET_PERI_REG_MASK(RTC_CNTL_INT_ENA_REG, RTC_CNTL_TOUCH_INT_ENA);
portEXIT_CRITICAL(&rtc_spinlock);
touch_pad_power_on(touch_num);
toch_pad_io_init(touch_num);
touch_pad_counter_init(touch_num);
touch_start(touch_num);
return ESP_OK;
}
esp_err_t touch_pad_read(touch_pad_t touch_num, uint16_t *touch_value)
{
RTC_MODULE_CHECK(touch_num < TOUCH_PAD_MAX, "Touch_Pad Num Err", ESP_ERR_INVALID_ARG);
RTC_MODULE_CHECK(touch_value!=NULL, "touch_value", ESP_ERR_INVALID_ARG);
uint32_t v0 = READ_PERI_REG(SENS_SAR_TOUCH_ENABLE_REG);
portENTER_CRITICAL(&rtc_spinlock);
SET_PERI_REG_MASK(SENS_SAR_TOUCH_ENABLE_REG, (1 << (touch_num)));
//Disable Intr
CLEAR_PERI_REG_MASK(SENS_SAR_TOUCH_ENABLE_REG, (1 << (touch_num + SENS_TOUCH_PAD_OUTEN2_S)) | \
((1 << (touch_num + SENS_TOUCH_PAD_OUTEN1_S))));
toch_pad_io_init(touch_num);
touch_pad_counter_init(touch_num);
touch_pad_power_on(touch_num);
//force oneTime test start
SET_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_START_EN_M);
SET_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_START_FORCE_M);
SET_PERI_REG_BITS(SENS_SAR_TOUCH_CTRL1_REG, SENS_TOUCH_XPD_WAIT, 10, SENS_TOUCH_XPD_WAIT_S);
while (GET_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_MEAS_DONE) == 0) {};
uint8_t shift = (touch_num & 1) ? SENS_TOUCH_MEAS_OUT1_S : SENS_TOUCH_MEAS_OUT0_S;
*touch_value = READ_PERI_REG(SENS_SAR_TOUCH_OUT1_REG + (touch_num / 2) * 4) >> shift;
WRITE_PERI_REG(SENS_SAR_TOUCH_ENABLE_REG, v0);
//force oneTime test end
//clear touch force ,select the Touch mode is Timer
CLEAR_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_START_EN_M);
CLEAR_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL2_REG, SENS_TOUCH_START_FORCE_M);
portEXIT_CRITICAL(&rtc_spinlock);
return ESP_OK;
}
/*---------------------------------------------------------------
ADC
---------------------------------------------------------------*/
static esp_err_t adc1_pad_get_io_num(adc1_channel_t channel, gpio_num_t *gpio_num)
{
RTC_MODULE_CHECK(channel < ADC1_CHANNEL_MAX, "ADC Channel Err", ESP_ERR_INVALID_ARG);
switch (channel) {
case ADC1_CHANNEL_0:
*gpio_num = 36;
break;
case ADC1_CHANNEL_1:
*gpio_num = 37;
break;
case ADC1_CHANNEL_2:
*gpio_num = 38;
break;
case ADC1_CHANNEL_3:
*gpio_num = 39;
break;
case ADC1_CHANNEL_4:
*gpio_num = 32;
break;
case ADC1_CHANNEL_5:
*gpio_num = 33;
break;
case ADC1_CHANNEL_6:
*gpio_num = 34;
break;
case ADC1_CHANNEL_7:
*gpio_num = 35;
break;
default:
return ESP_ERR_INVALID_ARG;
}
return ESP_OK;
}
static esp_err_t adc1_pad_init(adc1_channel_t channel)
{
gpio_num_t gpio_num = 0;
ADC1_CHECK_FUNCTION_RET(adc1_pad_get_io_num(channel, &gpio_num));
ADC1_CHECK_FUNCTION_RET(rtc_gpio_init(gpio_num));
ADC1_CHECK_FUNCTION_RET(rtc_gpio_output_disable(gpio_num));
ADC1_CHECK_FUNCTION_RET(rtc_gpio_input_disable(gpio_num));
ADC1_CHECK_FUNCTION_RET(gpio_set_pull_mode(gpio_num, GPIO_FLOATING));
return ESP_OK;
}
esp_err_t adc1_config_channel_atten(adc1_channel_t channel, adc_atten_t atten)
{
RTC_MODULE_CHECK(channel < ADC1_CHANNEL_MAX, "ADC Channel Err", ESP_ERR_INVALID_ARG);
RTC_MODULE_CHECK(atten <= ADC_ATTEN_11db, "ADC Atten Err", ESP_ERR_INVALID_ARG);
adc1_pad_init(channel);
portENTER_CRITICAL(&rtc_spinlock);
SET_PERI_REG_BITS(SENS_SAR_ATTEN1_REG, 3, atten, (channel * 2)); //SAR1_atten
portEXIT_CRITICAL(&rtc_spinlock);
return ESP_OK;
}
esp_err_t adc1_config_width(adc_bits_width_t width_bit)
{
portENTER_CRITICAL(&rtc_spinlock);
SET_PERI_REG_BITS(SENS_SAR_START_FORCE_REG, SENS_SAR1_BIT_WIDTH_V, width_bit, SENS_SAR1_BIT_WIDTH_S); //SAR2_BIT_WIDTH[1:0]=0x3, SAR1_BIT_WIDTH[1:0]=0x3
//Invert the adc value,the Output value is invert
SET_PERI_REG_MASK(SENS_SAR_READ_CTRL_REG, SENS_SAR1_DATA_INV);
//Set The adc sample width,invert adc value,must
SET_PERI_REG_BITS(SENS_SAR_READ_CTRL_REG, SENS_SAR1_SAMPLE_BIT_V, width_bit, SENS_SAR1_SAMPLE_BIT_S); //digital sar1_bit_width[1:0]=3
portEXIT_CRITICAL(&rtc_spinlock);
return ESP_OK;
}
int adc1_get_voltage(adc1_channel_t channel)
{
uint16_t adc_value;
RTC_MODULE_CHECK(channel < ADC1_CHANNEL_MAX, "ADC Channel Err", ESP_ERR_INVALID_ARG);
portENTER_CRITICAL(&rtc_spinlock);
//Adc Controler is Rtc module,not ulp coprocessor
SET_PERI_REG_BITS(SENS_SAR_MEAS_START1_REG, 1, 1, SENS_MEAS1_START_FORCE_S); //force pad mux and force start
//Bit1=0:Fsm Bit1=1(Bit0=0:PownDown Bit10=1:Powerup)
SET_PERI_REG_BITS(SENS_SAR_MEAS_WAIT2_REG, SENS_FORCE_XPD_SAR, 0, SENS_FORCE_XPD_SAR_S); //force XPD_SAR=0, use XPD_FSM
//Disable Amp Bit1=0:Fsm Bit1=1(Bit0=0:PownDown Bit10=1:Powerup)
SET_PERI_REG_BITS(SENS_SAR_MEAS_WAIT2_REG, SENS_FORCE_XPD_AMP, 0x2, SENS_FORCE_XPD_AMP_S); //force XPD_AMP=0
//Open the ADC1 Data port Not ulp coprocessor
SET_PERI_REG_BITS(SENS_SAR_MEAS_START1_REG, 1, 1, SENS_SAR1_EN_PAD_FORCE_S); //open the ADC1 data port
//Select channel
SET_PERI_REG_BITS(SENS_SAR_MEAS_START1_REG, SENS_SAR1_EN_PAD, (1 << channel), SENS_SAR1_EN_PAD_S); //pad enable
SET_PERI_REG_BITS(SENS_SAR_MEAS_CTRL_REG, 0xfff, 0x0, SENS_AMP_RST_FB_FSM_S); //[11:8]:short ref ground, [7:4]:short ref, [3:0]:rst fb
SET_PERI_REG_BITS(SENS_SAR_MEAS_WAIT1_REG, SENS_SAR_AMP_WAIT1, 0x1, SENS_SAR_AMP_WAIT1_S);
SET_PERI_REG_BITS(SENS_SAR_MEAS_WAIT1_REG, SENS_SAR_AMP_WAIT2, 0x1, SENS_SAR_AMP_WAIT2_S);
SET_PERI_REG_BITS(SENS_SAR_MEAS_WAIT2_REG, SENS_SAR_AMP_WAIT3, 0x1, SENS_SAR_AMP_WAIT3_S);
while (GET_PERI_REG_BITS2(SENS_SAR_SLAVE_ADDR1_REG, 0x7, SENS_MEAS_STATUS_S) != 0); //wait det_fsm==0
SET_PERI_REG_BITS(SENS_SAR_MEAS_START1_REG, 1, 0, SENS_MEAS1_START_SAR_S); //start force 0
SET_PERI_REG_BITS(SENS_SAR_MEAS_START1_REG, 1, 1, SENS_MEAS1_START_SAR_S); //start force 1
while (GET_PERI_REG_MASK(SENS_SAR_MEAS_START1_REG, SENS_MEAS1_DONE_SAR) == 0) {}; //read done
adc_value = GET_PERI_REG_BITS2(SENS_SAR_MEAS_START1_REG, SENS_MEAS1_DATA_SAR, SENS_MEAS1_DATA_SAR_S);
portEXIT_CRITICAL(&rtc_spinlock);
return adc_value;
}
/*---------------------------------------------------------------
DAC
---------------------------------------------------------------*/
static esp_err_t dac_pad_get_io_num(dac_channel_t channel, gpio_num_t *gpio_num)
{
RTC_MODULE_CHECK(channel < DAC_CHANNEL_MAX, "DAC Channel Err", ESP_ERR_INVALID_ARG);
switch (channel) {
case DAC_CHANNEL_1:
*gpio_num = 25;
break;
case DAC_CHANNEL_2:
*gpio_num = 26;
break;
default:
return ESP_ERR_INVALID_ARG;
}
return ESP_OK;
}
static esp_err_t dac_rtc_pad_init(dac_channel_t channel)
{
RTC_MODULE_CHECK(channel < DAC_CHANNEL_MAX, "DAC Channel Err", ESP_ERR_INVALID_ARG);
gpio_num_t gpio_num = 0;
dac_pad_get_io_num(channel, &gpio_num);
rtc_gpio_init(gpio_num);
rtc_gpio_output_disable(gpio_num);
rtc_gpio_input_disable(gpio_num);
rtc_gpio_pullup_dis(gpio_num);
rtc_gpio_pulldown_dis(gpio_num);
return ESP_OK;
}
static esp_err_t dac_out_enable(dac_channel_t channel)
{
if (channel == DAC_CHANNEL_1) {
portENTER_CRITICAL(&rtc_spinlock);
SET_PERI_REG_MASK(RTC_IO_PAD_DAC1_REG, RTC_IO_PDAC1_XPD_DAC | RTC_IO_PDAC1_DAC_XPD_FORCE);
portEXIT_CRITICAL(&rtc_spinlock);
} else if (channel == DAC_CHANNEL_2) {
portENTER_CRITICAL(&rtc_spinlock);
SET_PERI_REG_MASK(RTC_IO_PAD_DAC2_REG, RTC_IO_PDAC2_XPD_DAC | RTC_IO_PDAC2_DAC_XPD_FORCE);
portEXIT_CRITICAL(&rtc_spinlock);
} else {
return ESP_ERR_INVALID_ARG;
}
return ESP_OK;
}
esp_err_t dac_out_voltage(dac_channel_t channel, uint8_t dac_value)
{
RTC_MODULE_CHECK(channel < DAC_CHANNEL_MAX, "DAC Channel Err", ESP_ERR_INVALID_ARG);
portENTER_CRITICAL(&rtc_spinlock);
//Disable Tone
CLEAR_PERI_REG_MASK(SENS_SAR_DAC_CTRL1_REG, SENS_SW_TONE_EN);
//Disable Channel Tone
if (channel == DAC_CHANNEL_1) {
CLEAR_PERI_REG_MASK(SENS_SAR_DAC_CTRL2_REG, SENS_DAC_CW_EN1_M);
} else if (channel == DAC_CHANNEL_2) {
CLEAR_PERI_REG_MASK(SENS_SAR_DAC_CTRL2_REG, SENS_DAC_CW_EN2_M);
}
//Set the Dac value
if (channel == DAC_CHANNEL_1) {
SET_PERI_REG_BITS(RTC_IO_PAD_DAC1_REG, RTC_IO_PDAC1_DAC, dac_value, RTC_IO_PDAC1_DAC_S); //dac_output
} else if (channel == DAC_CHANNEL_2) {
SET_PERI_REG_BITS(RTC_IO_PAD_DAC2_REG, RTC_IO_PDAC2_DAC, dac_value, RTC_IO_PDAC2_DAC_S); //dac_output
}
portEXIT_CRITICAL(&rtc_spinlock);
//dac pad init
dac_rtc_pad_init(channel);
dac_out_enable(channel);
return ESP_OK;
}
/*---------------------------------------------------------------
HALL SENSOR
---------------------------------------------------------------*/
static int hall_sensor_get_value() //hall sensor without LNA
{
int Sens_Vp0;
int Sens_Vn0;
int Sens_Vp1;
int Sens_Vn1;
int hall_value;
portENTER_CRITICAL(&rtc_spinlock);
SET_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL1_REG, SENS_XPD_HALL_FORCE_M); // hall sens force enable
SET_PERI_REG_MASK(RTC_IO_HALL_SENS_REG, RTC_IO_XPD_HALL); // xpd hall
SET_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL1_REG, SENS_HALL_PHASE_FORCE_M); // phase force
CLEAR_PERI_REG_MASK(RTC_IO_HALL_SENS_REG, RTC_IO_HALL_PHASE); // hall phase
Sens_Vp0 = adc1_get_voltage(ADC1_CHANNEL_0);
Sens_Vn0 = adc1_get_voltage(ADC1_CHANNEL_3);
SET_PERI_REG_MASK(RTC_IO_HALL_SENS_REG, RTC_IO_HALL_PHASE);
Sens_Vp1 = adc1_get_voltage(ADC1_CHANNEL_0);
Sens_Vn1 = adc1_get_voltage(ADC1_CHANNEL_3);
SET_PERI_REG_BITS(SENS_SAR_MEAS_WAIT2_REG, SENS_FORCE_XPD_SAR, 0, SENS_FORCE_XPD_SAR_S);
CLEAR_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL1_REG, SENS_XPD_HALL_FORCE);
CLEAR_PERI_REG_MASK(SENS_SAR_TOUCH_CTRL1_REG, SENS_HALL_PHASE_FORCE);
portEXIT_CRITICAL(&rtc_spinlock);
hall_value = (Sens_Vp1 - Sens_Vp0) - (Sens_Vn1 - Sens_Vn0);
return hall_value;
}
int hall_sensor_read()
{
adc1_pad_init(ADC1_CHANNEL_0);
adc1_pad_init(ADC1_CHANNEL_3);
adc1_config_channel_atten(ADC1_CHANNEL_0, ADC_ATTEN_0db);
adc1_config_channel_atten(ADC1_CHANNEL_3, ADC_ATTEN_0db);
return hall_sensor_get_value();
}