mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
220 lines
9.8 KiB
Plaintext
220 lines
9.8 KiB
Plaintext
menu "ESP32C3-Specific"
|
|
visible if IDF_TARGET_ESP32C3
|
|
|
|
choice ESP32C3_DEFAULT_CPU_FREQ_MHZ
|
|
prompt "CPU frequency"
|
|
default ESP32C3_DEFAULT_CPU_FREQ_40 if IDF_ENV_FPGA
|
|
default ESP32C3_DEFAULT_CPU_FREQ_160 if !IDF_ENV_FPGA
|
|
help
|
|
CPU frequency to be set on application startup.
|
|
|
|
config ESP32C3_DEFAULT_CPU_FREQ_40
|
|
bool "40 MHz"
|
|
depends on IDF_ENV_FPGA
|
|
config ESP32C3_DEFAULT_CPU_FREQ_80
|
|
bool "80 MHz"
|
|
config ESP32C3_DEFAULT_CPU_FREQ_160
|
|
bool "160 MHz"
|
|
endchoice
|
|
|
|
config ESP32C3_DEFAULT_CPU_FREQ_MHZ
|
|
int
|
|
default 40 if ESP32C3_DEFAULT_CPU_FREQ_40
|
|
default 80 if ESP32C3_DEFAULT_CPU_FREQ_80
|
|
default 160 if ESP32C3_DEFAULT_CPU_FREQ_160
|
|
|
|
choice ESP32C3_UNIVERSAL_MAC_ADDRESSES
|
|
bool "Number of universally administered (by IEEE) MAC address"
|
|
default ESP32C3_UNIVERSAL_MAC_ADDRESSES_TWO
|
|
help
|
|
Configure the number of universally administered (by IEEE) MAC addresses.
|
|
During initialization, MAC addresses for each network interface are generated or derived from a
|
|
single base MAC address.
|
|
If the number of universal MAC addresses is Two, all interfaces (WiFi station, WiFi softap) receive a
|
|
universally administered MAC address. They are generated sequentially by adding 0, and 1 (respectively)
|
|
to the final octet of the base MAC address. If the number of universal MAC addresses is one,
|
|
only WiFi station receives a universally administered MAC address.
|
|
It's generated by adding 0 to the base MAC address.
|
|
The WiFi softap receives local MAC addresses. It's derived from the universal WiFi station MAC addresses.
|
|
When using the default (Espressif-assigned) base MAC address, either setting can be used. When using
|
|
a custom universal MAC address range, the correct setting will depend on the allocation of MAC
|
|
addresses in this range (either 1 or 2 per device.)
|
|
|
|
config ESP32C3_UNIVERSAL_MAC_ADDRESSES_TWO
|
|
bool "Two"
|
|
select ESP_MAC_ADDR_UNIVERSE_WIFI_STA
|
|
select ESP_MAC_ADDR_UNIVERSE_BT
|
|
config ESP32C3_UNIVERSAL_MAC_ADDRESSES_THREE
|
|
bool "Three"
|
|
select ESP_MAC_ADDR_UNIVERSE_WIFI_STA
|
|
select ESP_MAC_ADDR_UNIVERSE_WIFI_AP
|
|
select ESP_MAC_ADDR_UNIVERSE_BT
|
|
endchoice
|
|
|
|
config ESP32C3_UNIVERSAL_MAC_ADDRESSES
|
|
int
|
|
default 2 if ESP32C3_UNIVERSAL_MAC_ADDRESSES_TWO
|
|
default 3 if ESP32C3_UNIVERSAL_MAC_ADDRESSES_THREE
|
|
|
|
config ESP_MAC_ADDR_UNIVERSE_BT_OFFSET
|
|
int
|
|
default 2 if ESP32C3_UNIVERSAL_MAC_ADDRESSES_THREE
|
|
default 1 if ESP32C3_UNIVERSAL_MAC_ADDRESSES_TWO
|
|
|
|
config ESP32C3_DEBUG_OCDAWARE
|
|
bool "Make exception and panic handlers JTAG/OCD aware"
|
|
default y
|
|
select FREERTOS_DEBUG_OCDAWARE
|
|
help
|
|
The FreeRTOS panic and unhandled exception handers can detect a JTAG OCD debugger and
|
|
instead of panicking, have the debugger stop on the offending instruction.
|
|
|
|
config ESP32C3_DEBUG_STUBS_ENABLE
|
|
bool "OpenOCD debug stubs"
|
|
default COMPILER_OPTIMIZATION_LEVEL_DEBUG
|
|
depends on !ESP32C3_TRAX
|
|
help
|
|
Debug stubs are used by OpenOCD to execute pre-compiled onboard code which does some useful debugging,
|
|
e.g. GCOV data dump.
|
|
|
|
config ESP32C3_BROWNOUT_DET
|
|
# TODO ESP32-C3 IDF-2397
|
|
bool
|
|
default n
|
|
help
|
|
The ESP32-S3 has a built-in brownout detector which can detect if the voltage is lower than
|
|
a specific value. If this happens, it will reset the chip in order to prevent unintended
|
|
behaviour.
|
|
|
|
choice ESP32C3_BROWNOUT_DET_LVL_SEL
|
|
prompt "Brownout voltage level"
|
|
depends on ESP32C3_BROWNOUT_DET
|
|
default ESP32C3_BROWNOUT_DET_LVL_SEL_7
|
|
help
|
|
The brownout detector will reset the chip when the supply voltage is approximately
|
|
below this level. Note that there may be some variation of brownout voltage level
|
|
between each ESP3-S3 chip.
|
|
|
|
#The voltage levels here are estimates, more work needs to be done to figure out the exact voltages
|
|
#of the brownout threshold levels.
|
|
config ESP32C3_BROWNOUT_DET_LVL_SEL_7
|
|
bool "2.44V"
|
|
config ESP32C3_BROWNOUT_DET_LVL_SEL_6
|
|
bool "2.56V"
|
|
config ESP32C3_BROWNOUT_DET_LVL_SEL_5
|
|
bool "2.67V"
|
|
config ESP32C3_BROWNOUT_DET_LVL_SEL_4
|
|
bool "2.84V"
|
|
config ESP32C3_BROWNOUT_DET_LVL_SEL_3
|
|
bool "2.98V"
|
|
config ESP32C3_BROWNOUT_DET_LVL_SEL_2
|
|
bool "3.19V"
|
|
config ESP32C3_BROWNOUT_DET_LVL_SEL_1
|
|
bool "3.30V"
|
|
endchoice
|
|
|
|
config ESP32C3_BROWNOUT_DET_LVL
|
|
int
|
|
default 1 if ESP32C3_BROWNOUT_DET_LVL_SEL_1
|
|
default 2 if ESP32C3_BROWNOUT_DET_LVL_SEL_2
|
|
default 3 if ESP32C3_BROWNOUT_DET_LVL_SEL_3
|
|
default 4 if ESP32C3_BROWNOUT_DET_LVL_SEL_4
|
|
default 5 if ESP32C3_BROWNOUT_DET_LVL_SEL_5
|
|
default 6 if ESP32C3_BROWNOUT_DET_LVL_SEL_6
|
|
default 7 if ESP32C3_BROWNOUT_DET_LVL_SEL_7
|
|
|
|
choice ESP32C3_TIME_SYSCALL
|
|
prompt "Timers used for gettimeofday function"
|
|
default ESP32C3_TIME_SYSCALL_USE_RTC_SYSTIMER
|
|
help
|
|
This setting defines which hardware timers are used to
|
|
implement 'gettimeofday' and 'time' functions in C library.
|
|
|
|
- If both high-resolution (systimer) and RTC timers are used, timekeeping will
|
|
continue in deep sleep. Time will be reported at 1 microsecond
|
|
resolution. This is the default, and the recommended option.
|
|
- If only high-resolution timer (systimer) is used, gettimeofday will
|
|
provide time at microsecond resolution.
|
|
Time will not be preserved when going into deep sleep mode.
|
|
- If only RTC timer is used, timekeeping will continue in
|
|
deep sleep, but time will be measured at 6.(6) microsecond
|
|
resolution. Also the gettimeofday function itself may take
|
|
longer to run.
|
|
- If no timers are used, gettimeofday and time functions
|
|
return -1 and set errno to ENOSYS.
|
|
- When RTC is used for timekeeping, two RTC_STORE registers are
|
|
used to keep time in deep sleep mode.
|
|
|
|
config ESP32C3_TIME_SYSCALL_USE_RTC_SYSTIMER
|
|
bool "RTC and high-resolution timer"
|
|
select ESP_TIME_FUNCS_USE_RTC_TIMER
|
|
select ESP_TIME_FUNCS_USE_ESP_TIMER
|
|
config ESP32C3_TIME_SYSCALL_USE_RTC
|
|
bool "RTC"
|
|
select ESP_TIME_FUNCS_USE_RTC_TIMER
|
|
config ESP32C3_TIME_SYSCALL_USE_SYSTIMER
|
|
bool "High-resolution timer"
|
|
select ESP_TIME_FUNCS_USE_ESP_TIMER
|
|
config ESP32C3_TIME_SYSCALL_USE_NONE
|
|
bool "None"
|
|
select ESP_TIME_FUNCS_USE_NONE
|
|
endchoice
|
|
|
|
choice ESP32C3_RTC_CLK_SRC
|
|
prompt "RTC clock source"
|
|
default ESP32C3_RTC_CLK_SRC_INT_RC
|
|
help
|
|
Choose which clock is used as RTC clock source.
|
|
|
|
config ESP32C3_RTC_CLK_SRC_INT_RC
|
|
bool "Internal 150kHz RC oscillator"
|
|
config ESP32C3_RTC_CLK_SRC_EXT_CRYS
|
|
bool "External 32kHz crystal"
|
|
select ESP_SYSTEM_RTC_EXT_XTAL
|
|
config ESP32C3_RTC_CLK_SRC_EXT_OSC
|
|
bool "External 32kHz oscillator at 32K_XP pin"
|
|
config ESP32C3_RTC_CLK_SRC_INT_8MD256
|
|
bool "Internal 8MHz oscillator, divided by 256 (~32kHz)"
|
|
endchoice
|
|
|
|
config ESP32C3_RTC_CLK_CAL_CYCLES
|
|
int "Number of cycles for RTC_SLOW_CLK calibration"
|
|
default 3000 if ESP32C3_RTC_CLK_SRC_EXT_CRYS || ESP32C3_RTC_CLK_SRC_EXT_OSC || ESP32C3_RTC_CLK_SRC_INT_8MD256
|
|
default 1024 if ESP32C3_RTC_CLK_SRC_INT_RC
|
|
range 0 125000
|
|
help
|
|
When the startup code initializes RTC_SLOW_CLK, it can perform
|
|
calibration by comparing the RTC_SLOW_CLK frequency with main XTAL
|
|
frequency. This option sets the number of RTC_SLOW_CLK cycles measured
|
|
by the calibration routine. Higher numbers increase calibration
|
|
precision, which may be important for applications which spend a lot of
|
|
time in deep sleep. Lower numbers reduce startup time.
|
|
|
|
When this option is set to 0, clock calibration will not be performed at
|
|
startup, and approximate clock frequencies will be assumed:
|
|
|
|
- 150000 Hz if internal RC oscillator is used as clock source. For this use value 1024.
|
|
- 32768 Hz if the 32k crystal oscillator is used. For this use value 3000 or more.
|
|
In case more value will help improve the definition of the launch of the crystal.
|
|
If the crystal could not start, it will be switched to internal RC.
|
|
|
|
config ESP32C3_NO_BLOBS
|
|
bool "No Binary Blobs"
|
|
depends on !BT_ENABLED
|
|
default n
|
|
help
|
|
If enabled, this disables the linking of binary libraries in the application build. Note
|
|
that after enabling this Wi-Fi/Bluetooth will not work.
|
|
|
|
config ESP32C3_ALLOW_RTC_FAST_MEM_AS_HEAP
|
|
bool "Enable RTC fast memory for dynamic allocations"
|
|
depends on !ESP32C3_MEMPROT_FEATURE
|
|
default y
|
|
help
|
|
This config option allows to add RTC fast memory region to system heap with capability
|
|
similar to that of DRAM region but without DMA. This memory will be consumed first per
|
|
heap initialization order by early startup services and scheduler related code. Speed
|
|
wise RTC fast memory operates on APB clock and hence does not have much performance impact.
|
|
|
|
endmenu # ESP32C3-Specific
|