mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
145 lines
4.4 KiB
C
145 lines
4.4 KiB
C
/*
|
|
* SPDX-FileCopyrightText: 2019-2022 Espressif Systems (Shanghai) CO LTD
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/**
|
|
* System level MSPI APIs (private)
|
|
*/
|
|
/**
|
|
* Currently the MSPI timing tuning related APIs are designed to be private.
|
|
* Because:
|
|
* 1. now we don't split SPI0 and SPI1, we don't have a component for SPI0, including PSRAM, Cache, etc..
|
|
* 2. SPI0 and SPI1 are strongly coupling.
|
|
*
|
|
* In the future, we may consider creating a component for SPI0, and spi_flash component will only work on SPI1 (and it
|
|
* can rely on SPI0). Therefore, we can put these APIs there.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
#include <stdint.h>
|
|
#include <stdbool.h>
|
|
#include "sdkconfig.h"
|
|
#include "esp_rom_spiflash.h"
|
|
#include "esp_err.h"
|
|
#include "esp_flash.h"
|
|
#include "hal/spi_flash_hal.h"
|
|
#include "spi_flash_override.h"
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
/**
|
|
* @brief To setup Flash chip
|
|
*/
|
|
esp_err_t spi_flash_init_chip_state(void);
|
|
|
|
/**
|
|
* @brief Make MSPI work under 20Mhz, remove the timing tuning required delays.
|
|
* @param control_spi1 Select whether to control SPI1. For tuning, we need to use SPI1. After tuning (during startup stage), let the flash driver to control SPI1
|
|
*/
|
|
void spi_timing_enter_mspi_low_speed_mode(bool control_spi1);
|
|
|
|
/**
|
|
* @brief Make MSPI work under the frequency as users set, may add certain delays to MSPI RX direction to meet timing requirements.
|
|
* @param control_spi1 Select whether to control SPI1. For tuning, we need to use SPI1. After tuning (during startup stage), let the flash driver to control SPI1
|
|
*/
|
|
void spi_timing_enter_mspi_high_speed_mode(bool control_spi1);
|
|
|
|
/**
|
|
* @brief Switch MSPI into low speed mode / high speed mode.
|
|
* @note This API is cache safe, it will freeze both D$ and I$ and restore them after MSPI is switched
|
|
* @note For some of the MSPI high frequency settings (e.g. 80M DDR mode Flash or PSRAM), timing tuning is required.
|
|
* Certain delays will be added to the MSPI RX direction. When CPU clock switches from PLL to XTAL, should call
|
|
* this API first to enter MSPI low speed mode to remove the delays, and vice versa.
|
|
*/
|
|
void spi_timing_change_speed_mode_cache_safe(bool switch_down);
|
|
|
|
/**
|
|
* @brief Tune MSPI flash timing to make it work under high frequency
|
|
*/
|
|
void spi_timing_flash_tuning(void);
|
|
|
|
/**
|
|
* @brief Tune MSPI psram timing to make it work under high frequency
|
|
*/
|
|
void spi_timing_psram_tuning(void);
|
|
|
|
/**
|
|
* @brief To initislize the MSPI pins
|
|
*/
|
|
void esp_mspi_pin_init(void);
|
|
|
|
/**
|
|
* @brief Set SPI1 registers to make ROM functions work
|
|
* @note This function is used for setting SPI1 registers to the state that ROM SPI functions work
|
|
*/
|
|
void spi_flash_set_rom_required_regs(void);
|
|
|
|
/**
|
|
* @brief Initialize main flash
|
|
* @param chip Pointer to main SPI flash(SPI1 CS0) chip to use..
|
|
*/
|
|
esp_err_t esp_flash_init_main(esp_flash_t *chip);
|
|
|
|
/**
|
|
* @brief Should be only used by SPI1 Flash driver to know the necessary timing registers
|
|
* @param out_timing_config Pointer to timing_tuning parameters.
|
|
*/
|
|
void spi_timing_get_flash_timing_param(spi_flash_hal_timing_config_t *out_timing_config);
|
|
|
|
/**
|
|
* @brief Get the knowledge if the MSPI timing is tuned or not
|
|
*/
|
|
bool spi_timing_is_tuned(void);
|
|
|
|
/**
|
|
* @brief Set Flash chip specifically required MSPI register settings here
|
|
*/
|
|
void spi_flash_set_vendor_required_regs(void);
|
|
|
|
/**
|
|
* @brief Judge whether need to reset flash when brownout.
|
|
* Set` flash_brownout_needs_reset` inside the function if really need reset.
|
|
*/
|
|
void spi_flash_needs_reset_check(void);
|
|
|
|
/**
|
|
* @brief Set flag to reset flash. set when erase chip or program chip
|
|
*
|
|
* @param bool status. True if flash is eraing. False if flash is not erasing.
|
|
*
|
|
* @return None.
|
|
*/
|
|
void spi_flash_set_erasing_flag(bool status);
|
|
|
|
/**
|
|
* @brief Judge whether need to reset flash when brownout.
|
|
*
|
|
* @return true if need reset, otherwise false.
|
|
*/
|
|
bool spi_flash_brownout_need_reset(void);
|
|
|
|
/**
|
|
* @brief Enable SPI flash high performance mode.
|
|
*
|
|
* @return ESP_OK if success.
|
|
*/
|
|
esp_err_t spi_flash_enable_high_performance_mode(void);
|
|
|
|
/**
|
|
* @brief Get the flash dummy through this function
|
|
* This can be used when one flash has several dummy configurations to enable the high performance mode.
|
|
* @note Don't forget to subtract one when assign to the register of mspi e.g. if the value you get is 4, (4-1=3) should be assigned to the register.
|
|
*
|
|
* @return Pointer to bootlaoder_flash_dummy_conf_t.
|
|
*/
|
|
const spi_flash_hpm_dummy_conf_t *spi_flash_get_dummy(void);
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|