mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
6353bc40d7
- RTC_CNTL_SLOWCLK_FREQ define is removed; rtc_clk_slow_freq_get_hz function can be used instead to get an approximate RTC_SLOW_CLK frequency - Clock calibration is performed at startup. The value is saved and used for timekeeping and when entering deep sleep. - When using the 32k XTAL, startup code will wait for the oscillator to start up. This can be possibly optimized by starting a separate task to wait for oscillator startup, and performing clock switch in that task. - Fix a bug that 32k XTAL would be disabled in rtc_clk_init. - Fix a rounding error in rtc_clk_cal, which caused systematic frequency error. - Fix an overflow bug which caused rtc_clk_cal to timeout early if the slow_clk_cycles argument would exceed certain value - Improve 32k XTAL oscillator startup time by introducing bootstrapping code, which uses internal pullup/pulldown resistors on 32K_N/32K_P pins to set better initial conditions for the oscillator.
132 lines
4.7 KiB
C
132 lines
4.7 KiB
C
// Copyright 2015-2017 Espressif Systems (Shanghai) PTE LTD
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
//
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
#include <stdint.h>
|
|
#include "sdkconfig.h"
|
|
#include "esp_attr.h"
|
|
#include "esp_log.h"
|
|
#include "rom/ets_sys.h"
|
|
#include "rom/uart.h"
|
|
#include "soc/soc.h"
|
|
#include "soc/rtc.h"
|
|
#include "soc/rtc_cntl_reg.h"
|
|
|
|
/* Number of cycles to wait from the 32k XTAL oscillator to consider it running.
|
|
* Larger values increase startup delay. Smaller values may cause false positive
|
|
* detection (i.e. oscillator runs for a few cycles and then stops).
|
|
*/
|
|
#define XTAL_32K_DETECT_CYCLES 32
|
|
#define SLOW_CLK_CAL_CYCLES CONFIG_ESP32_RTC_CLK_CAL_CYCLES
|
|
|
|
static void select_rtc_slow_clk(rtc_slow_freq_t slow_clk);
|
|
|
|
static const char* TAG = "clk";
|
|
/*
|
|
* This function is not exposed as an API at this point,
|
|
* because FreeRTOS doesn't yet support dynamic changing of
|
|
* CPU frequency. Also we need to implement hooks for
|
|
* components which want to be notified of CPU frequency
|
|
* changes.
|
|
*/
|
|
void esp_clk_init(void)
|
|
{
|
|
rtc_config_t cfg = RTC_CONFIG_DEFAULT();
|
|
rtc_init(cfg);
|
|
|
|
#ifdef CONFIG_ESP32_RTC_CLOCK_SOURCE_EXTERNAL_CRYSTAL
|
|
select_rtc_slow_clk(RTC_SLOW_FREQ_32K_XTAL);
|
|
#else
|
|
select_rtc_slow_clk(RTC_SLOW_FREQ_RTC);
|
|
#endif
|
|
|
|
uint32_t freq_mhz = CONFIG_ESP32_DEFAULT_CPU_FREQ_MHZ;
|
|
rtc_cpu_freq_t freq = RTC_CPU_FREQ_80M;
|
|
switch(freq_mhz) {
|
|
case 240:
|
|
freq = RTC_CPU_FREQ_240M;
|
|
break;
|
|
case 160:
|
|
freq = RTC_CPU_FREQ_160M;
|
|
break;
|
|
default:
|
|
freq_mhz = 80;
|
|
/* no break */
|
|
case 80:
|
|
freq = RTC_CPU_FREQ_80M;
|
|
break;
|
|
}
|
|
|
|
// Wait for UART TX to finish, otherwise some UART output will be lost
|
|
// when switching APB frequency
|
|
uart_tx_wait_idle(CONFIG_CONSOLE_UART_NUM);
|
|
rtc_clk_cpu_freq_set(freq);
|
|
}
|
|
|
|
void IRAM_ATTR ets_update_cpu_frequency(uint32_t ticks_per_us)
|
|
{
|
|
extern uint32_t g_ticks_per_us_pro; // g_ticks_us defined in ROM for PRO CPU
|
|
extern uint32_t g_ticks_per_us_app; // same defined for APP CPU
|
|
g_ticks_per_us_pro = ticks_per_us;
|
|
g_ticks_per_us_app = ticks_per_us;
|
|
}
|
|
|
|
/* This is a cached value of RTC slow clock period; it is updated by
|
|
* the select_rtc_slow_clk function at start up. This cached value is used in
|
|
* other places, like time syscalls and deep sleep.
|
|
*/
|
|
static uint32_t s_rtc_slow_clk_cal = 0;
|
|
|
|
static void select_rtc_slow_clk(rtc_slow_freq_t slow_clk)
|
|
{
|
|
if (slow_clk == RTC_SLOW_FREQ_32K_XTAL) {
|
|
/* 32k XTAL oscillator needs to be enabled and running before it can
|
|
* be used. Hardware doesn't have a direct way of checking if the
|
|
* oscillator is running. Here we use rtc_clk_cal function to count
|
|
* the number of main XTAL cycles in the given number of 32k XTAL
|
|
* oscillator cycles. If the 32k XTAL has not started up, calibration
|
|
* will time out, returning 0.
|
|
*/
|
|
rtc_clk_32k_enable(true);
|
|
uint32_t cal_val = 0;
|
|
uint32_t wait = 0;
|
|
// increment of 'wait' counter equivalent to 3 seconds
|
|
const uint32_t warning_timeout = 3 /* sec */ * 32768 /* Hz */ / (2 * XTAL_32K_DETECT_CYCLES);
|
|
ESP_EARLY_LOGD(TAG, "waiting for 32k oscillator to start up")
|
|
do {
|
|
++wait;
|
|
cal_val = rtc_clk_cal(RTC_CAL_32K_XTAL, XTAL_32K_DETECT_CYCLES);
|
|
if (wait % warning_timeout == 0) {
|
|
ESP_EARLY_LOGW(TAG, "still waiting for 32k oscillator to start up");
|
|
}
|
|
} while (cal_val == 0);
|
|
ESP_EARLY_LOGD(TAG, "32k oscillator ready, wait=%d", wait);
|
|
}
|
|
rtc_clk_slow_freq_set(slow_clk);
|
|
if (SLOW_CLK_CAL_CYCLES > 0) {
|
|
/* TODO: 32k XTAL oscillator has some frequency drift at startup.
|
|
* Improve calibration routine to wait until the frequency is stable.
|
|
*/
|
|
s_rtc_slow_clk_cal = rtc_clk_cal(RTC_CAL_RTC_MUX, SLOW_CLK_CAL_CYCLES);
|
|
} else {
|
|
const uint64_t cal_dividend = (1ULL << RTC_CLK_CAL_FRACT) * 1000000ULL;
|
|
s_rtc_slow_clk_cal = (uint32_t) (cal_dividend / rtc_clk_slow_freq_get_hz());
|
|
}
|
|
ESP_EARLY_LOGD(TAG, "RTC_SLOW_CLK calibration value: %d", s_rtc_slow_clk_cal);
|
|
}
|
|
|
|
uint32_t esp_clk_slowclk_cal_get()
|
|
{
|
|
return s_rtc_slow_clk_cal;
|
|
}
|