mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
d1132ddfa2
feat(lp-core): added support for using ETM events as wake-up source Closes IDF-10201 and IDF-6360 See merge request espressif/esp-idf!31810
269 lines
15 KiB
ReStructuredText
269 lines
15 KiB
ReStructuredText
ULP LP-Core Coprocessor Programming
|
|
===================================
|
|
|
|
:link_to_translation:`zh_CN:[中文]`
|
|
|
|
The ULP LP-Core (Low-power core) coprocessor is a variant of the ULP present in {IDF_TARGET_NAME}. It features ultra-low power consumption while also being able to stay powered on while the main CPU stays in low-power modes. This enables the LP-Core coprocessor to handle tasks like GPIO or sensor readings while the main CPU is in sleep mode, resulting in significant overall power savings for the entire system.
|
|
|
|
The ULP LP-Core coprocessor has the following features:
|
|
|
|
* A RV32I (32-bit RISC-V ISA) processor, with the multiplication/division (M), atomic (A), and compressed (C) extensions.
|
|
* Interrupt controller.
|
|
* Includes a debug module that supports external debugging via JTAG.
|
|
* Can access all of the High-power (HP) SRAM and peripherals when the entire system is active.
|
|
* Can access the Low-power (LP) SRAM and peripherals when the HP system is in sleep mode.
|
|
|
|
Compiling Code for the ULP LP-Core
|
|
----------------------------------
|
|
|
|
The ULP LP-Core code is compiled together with your ESP-IDF project as a separate binary and automatically embedded into the main project binary. To achieve this do the following:
|
|
|
|
1. Place the ULP LP-Core code, written in C or assembly (with the ``.S`` extension), in a dedicated directory within the component directory, such as ``ulp/``.
|
|
|
|
2. After registering the component in the CMakeLists.txt file, call the ``ulp_embed_binary`` function. Here is an example:
|
|
|
|
.. code-block:: cmake
|
|
|
|
idf_component_register()
|
|
|
|
set(ulp_app_name ulp_${COMPONENT_NAME})
|
|
set(ulp_sources "ulp/ulp_c_source_file.c" "ulp/ulp_assembly_source_file.S")
|
|
set(ulp_exp_dep_srcs "ulp_c_source_file.c")
|
|
|
|
ulp_embed_binary(${ulp_app_name} "${ulp_sources}" "${ulp_exp_dep_srcs}")
|
|
|
|
The first argument to ``ulp_embed_binary`` specifies the ULP binary name. The name specified here is also used by other generated artifacts such as the ELF file, map file, header file, and linker export file. The second argument specifies the ULP source files. Finally, the third argument specifies the list of component source files which include the header file to be generated. This list is needed to build the dependencies correctly and ensure that the generated header file is created before any of these files are compiled. See the section below for the concept of generated header files for ULP applications.
|
|
|
|
1. Enable both :ref:`CONFIG_ULP_COPROC_ENABLED` and :ref:`CONFIG_ULP_COPROC_TYPE` in menuconfig, and set :ref:`CONFIG_ULP_COPROC_TYPE` to ``CONFIG_ULP_COPROC_TYPE_LP_CORE``. The :ref:`CONFIG_ULP_COPROC_RESERVE_MEM` option reserves RTC memory for the ULP, and must be set to a value big enough to store both the ULP LP-Core code and data. If the application components contain multiple ULP programs, then the size of the RTC memory must be sufficient to hold the largest one.
|
|
|
|
2. Build the application as usual (e.g., ``idf.py app``).
|
|
|
|
During the build process, the following steps are taken to build ULP program:
|
|
|
|
1. **Run each source file through the C compiler and assembler.** This step generates the object files ``.obj.c`` or ``.obj.S`` in the component build directory depending on the source file processed.
|
|
|
|
2. **Run the linker script template through the C preprocessor.** The template is located in ``components/ulp/ld`` directory.
|
|
|
|
3. **Link the object files into an output ELF file** (``ulp_app_name.elf``). The Map file ``ulp_app_name.map`` generated at this stage may be useful for debugging purposes.
|
|
|
|
4. **Dump the contents of the ELF file into a binary** (``ulp_app_name.bin``) which can then be embedded into the application.
|
|
|
|
5. **Generate a list of global symbols** (``ulp_app_name.sym``) in the ELF file using ``riscv32-esp-elf-nm``.
|
|
|
|
6. **Create an LD export script and a header file** ``ulp_app_name.ld`` and ``ulp_app_name.h`` containing the symbols from ``ulp_app_name.sym``. This is done using the ``esp32ulp_mapgen.py`` utility.
|
|
|
|
7. **Add the generated binary to the list of binary files** to be embedded into the application.
|
|
|
|
.. _ulp-lp-core-access-variables:
|
|
|
|
Accessing the ULP LP-Core Program Variables
|
|
-------------------------------------------
|
|
|
|
Global symbols defined in the ULP LP-Core program may be used inside the main program.
|
|
|
|
For example, the ULP LP-Core program may define a variable ``measurement_count`` which defines the number of GPIO measurements the program needs to make before waking up the chip from Deep-sleep.
|
|
|
|
.. code-block:: c
|
|
|
|
volatile int measurement_count;
|
|
|
|
int some_function()
|
|
{
|
|
//read the measurement count for later use.
|
|
int temp = measurement_count;
|
|
|
|
...do something.
|
|
}
|
|
|
|
The main program can access the global ULP LP-Core program variables as the build system makes this possible by generating the ``${ULP_APP_NAME}.h`` and ``${ULP_APP_NAME}.ld`` files which define the global symbols present in the ULP LP-Core program. Each global symbol defined in the ULP LP-Core program is included in these files and are prefixed with ``ulp_``.
|
|
|
|
The header file contains the declaration of the symbol:
|
|
|
|
.. code-block:: c
|
|
|
|
extern uint32_t ulp_measurement_count;
|
|
|
|
Note that all symbols (variables, arrays, functions) are declared as ``uint32_t``. For functions and arrays, take the address of the symbol and cast it to the appropriate type.
|
|
|
|
The generated linker script file defines the locations of symbols in LP_MEM:
|
|
|
|
.. code-block:: none
|
|
|
|
PROVIDE ( ulp_measurement_count = 0x50000060 );
|
|
|
|
To access the ULP LP-Core program variables from the main program, the generated header file should be included using an ``include`` statement. This allows the ULP LP-Core program variables to be accessed as regular variables.
|
|
|
|
.. code-block:: c
|
|
|
|
#include "ulp_app_name.h"
|
|
|
|
void init_ulp_vars() {
|
|
ulp_measurement_count = 64;
|
|
}
|
|
|
|
.. note::
|
|
|
|
Variables declared in the global scope of the LP-Core program reside in either the ``.bss`` or ``.data`` section of the binary. These sections are initialized when the LP-Core binary is loaded and executed. Accessing these variables from the main program on the HP-Core before the first LP-Core run may result in undefined behavior.
|
|
|
|
|
|
Starting the ULP LP-Core Program
|
|
--------------------------------
|
|
|
|
To run a ULP LP-Core program, the main application needs to load the ULP program into RTC memory using the :cpp:func:`ulp_lp_core_load_binary` function, and then start it using the :cpp:func:`ulp_lp_core_run` function.
|
|
|
|
Each ULP LP-Core program is embedded into the ESP-IDF application as a binary blob. The application can reference this blob and load it in the following way (supposed ULP_APP_NAME was defined to ``ulp_app_name``):
|
|
|
|
.. code-block:: c
|
|
|
|
extern const uint8_t bin_start[] asm("_binary_ulp_app_name_bin_start");
|
|
extern const uint8_t bin_end[] asm("_binary_ulp_app_name_bin_end");
|
|
|
|
void start_ulp_program() {
|
|
ESP_ERROR_CHECK( ulp_lp_core_load_binary( bin_start,
|
|
(bin_end - bin_start)) );
|
|
}
|
|
|
|
Once the program is loaded into LP memory, the application can be configured and started by calling :cpp:func:`ulp_lp_core_run`:
|
|
|
|
.. code-block:: c
|
|
|
|
ulp_lp_core_cfg_t cfg = {
|
|
.wakeup_source = ULP_LP_CORE_WAKEUP_SOURCE_LP_TIMER, // LP core will be woken up periodically by LP timer
|
|
.lp_timer_sleep_duration_us = 10000,
|
|
};
|
|
|
|
ESP_ERROR_CHECK( ulp_lp_core_run(&cfg) );
|
|
|
|
ULP LP-Core Program Flow
|
|
------------------------
|
|
|
|
How the ULP LP-Core coprocessor is started depends on the wake-up source selected in :cpp:type:`ulp_lp_core_cfg_t`. The most common use-case is for the ULP to periodically wake up, do some measurements before either waking up the main CPU or going back to sleep again.
|
|
|
|
The ULP has the following wake-up sources:
|
|
* :c:macro:`ULP_LP_CORE_WAKEUP_SOURCE_HP_CPU` - LP Core can be woken up by the HP CPU.
|
|
* :c:macro:`ULP_LP_CORE_WAKEUP_SOURCE_LP_TIMER` - LP Core can be woken up by the LP timer.
|
|
* :c:macro:`ULP_LP_CORE_WAKEUP_SOURCE_ETM` - LP Core can be woken up by a ETM event. (Not yet supported)
|
|
* :c:macro:`ULP_LP_CORE_WAKEUP_SOURCE_LP_IO` - LP Core can be woken up when LP IO level changes. (Not yet supported)
|
|
* :c:macro:`ULP_LP_CORE_WAKEUP_SOURCE_LP_UART` - LP Core can be woken up after receiving a certain number of UART RX pulses. (Not yet supported)
|
|
|
|
When the ULP is woken up, it will go through the following steps:
|
|
|
|
.. list::
|
|
|
|
:CONFIG_ESP_ROM_HAS_LP_ROM: #. Unless :cpp:member:`ulp_lp_core_cfg_t::skip_lp_rom_boot` is specified, run ROM start-up code and jump to the entry point in LP RAM. ROM start-up code will initialize LP UART as well as print boot messages.
|
|
#. Initialize system feature, e.g., interrupts
|
|
#. Call user code ``main()``
|
|
#. Return from ``main()``
|
|
#. If ``lp_timer_sleep_duration_us`` is specified, then configure the next wake-up alarm
|
|
#. Call :cpp:func:`ulp_lp_core_halt`
|
|
|
|
|
|
ULP LP-Core Peripheral Support
|
|
------------------------------
|
|
|
|
To enhance the capabilities of the ULP LP-Core coprocessor, it has access to peripherals that operate in the low-power domain. The ULP LP-Core coprocessor can interact with these peripherals when the main CPU is in sleep mode, and can wake up the main CPU once a wake-up condition is reached. The following peripherals are supported:
|
|
|
|
.. list::
|
|
|
|
* LP IO
|
|
* LP I2C
|
|
* LP UART
|
|
:SOC_LP_SPI_SUPPORTED: * LP SPI
|
|
|
|
.. only:: CONFIG_ESP_ROM_HAS_LP_ROM
|
|
|
|
ULP LP-Core ROM
|
|
---------------
|
|
|
|
The ULP LP-Core ROM is a small pre-built piece of code located in LP-ROM, which can't be modified. Similar to the bootloader ROM code ran by the main CPU, this code is executed when the ULP LP-Core coprocessor is started. The ROM code initializes the ULP LP-Core coprocessor and then jumps to the user program. The ROM code also prints boot messages if the LP UART has been initialized.
|
|
|
|
The ROM code is not executed if :cpp:member:`ulp_lp_core_cfg_t::skip_lp_rom_boot` is set to true. This is useful when you need the ULP to wake-up as quickly as possible and the extra overhead of initializing and printing is unwanted.
|
|
|
|
In addition to the boot-up code mentioned above, the ROM code also provides the following functions and interfaces:
|
|
|
|
* :component_file:`ROM.ld Interface <esp_rom/{IDF_TARGET_PATH_NAME}/ld/{IDF_TARGET_PATH_NAME}lp.rom.ld>`
|
|
* :component_file:`newlib.ld Interface <esp_rom/{IDF_TARGET_PATH_NAME}/ld/{IDF_TARGET_PATH_NAME}lp.rom.newlib.ld>`
|
|
|
|
Since these functions are already present in LP-ROM no matter what, using these in your program allows you to reduce the RAM footprint of your ULP application.
|
|
|
|
|
|
ULP LP-Core Interrupts
|
|
----------------------
|
|
|
|
The LP-Core coprocessor can be configured to handle interrupts from various sources. Examples of such interrupts could be LP IO low/high or LP timer interrupts. To register a handler for an interrupt, simply override any of the weak handlers provided by IDF. A complete list of handlers can be found in :component_file:`ulp_lp_core_interrupts.h <ulp/lp_core/lp_core/include/ulp_lp_core_interrupts.h>`. For details on which interrupts are available on a specific target, please consult **{IDF_TARGET_NAME} Technical Reference Manual** [`PDF <{IDF_TARGET_TRM_EN_URL}#ulp>`__].
|
|
|
|
For example, to override the handler for the LP IO interrupt, you can define the following function in your ULP LP-Core code:
|
|
|
|
.. code-block:: c
|
|
|
|
void LP_CORE_ISR_ATTR ulp_lp_core_lp_io_intr_handler(void)
|
|
{
|
|
// Handle the interrupt and clear the interrupt source
|
|
}
|
|
|
|
:c:macro:`LP_CORE_ISR_ATTR` is a macro that is used to define the interrupt handler function. This macro ensures that registers are saved and restored correctly when the interrupt handler is called.
|
|
|
|
In addition to configuring the interrupt related registers for the interrupt source you want to handle, you also need to enable the interrupts globally in the LP-Core interrupt controller. This can be done using the :cpp:func:`ulp_lp_core_intr_enable` function.
|
|
|
|
Debugging ULP LP-Core Applications
|
|
----------------------------------
|
|
|
|
When programming the LP-Core, it can sometimes be challenging to figure out why the program is not behaving as expected. Here are some strategies to help you debug your LP-Core program:
|
|
|
|
* Use the LP-UART to print: the LP-Core has access to the LP-UART peripheral, which can be used for printing information independently of the main CPU sleep state. See :example:`system/ulp/lp_core/lp_uart/lp_uart_print` for an example of how to use this driver.
|
|
|
|
* Share program state through shared variables: as described in :ref:`ulp-lp-core-access-variables`, both the main CPU and the ULP core can easily access global variables in RTC memory. Writing state information to such a variable from the ULP and reading it from the main CPU can help you discern what is happening on the ULP core. The downside of this approach is that it requires the main CPU to be awake, which will not always be the case. Keeping the main CPU awake might even, in some cases, mask problems, as some issues may only occur when certain power domains are powered down.
|
|
|
|
* Panic handler: the LP-Core has a panic handler that can dump the state of the LP-Core registers by the LP-UART when an exception is detected. To enable the panic handler, set the :ref:`CONFIG_ULP_PANIC_OUTPUT_ENABLE` option to ``y``. This option can be kept disabled to reduce LP-RAM usage by the LP-Core application. To recover a backtrace from the panic dump, it is possible to use esp-idf-monitor_., e.g.:
|
|
|
|
.. code-block:: bash
|
|
|
|
python -m esp_idf_monitor --toolchain-prefix riscv32-esp-elf- --target {IDF_TARGET_NAME} --decode-panic backtrace PATH_TO_ULP_ELF_FILE
|
|
|
|
|
|
Application Examples
|
|
--------------------
|
|
|
|
* :example:`system/ulp/lp_core/gpio` polls GPIO while main CPU is in Deep-sleep.
|
|
* :example:`system/ulp/lp_core/lp_i2c` reads external I2C ambient light sensor (BH1750) while the main CPU is in Deep-sleep and wakes up the main CPU once a threshold is met.
|
|
* :example:`system/ulp/lp_core/lp_uart/lp_uart_echo` reads data written to a serial console and echoes it back. This example demonstrates the usage of the LP UART driver running on the LP core.
|
|
* :example:`system/ulp/lp_core/lp_uart/lp_uart_print` shows how to print various statements from a program running on the LP core.
|
|
* :example:`system/ulp/lp_core/interrupt` shows how to register an interrupt handler on the LP core to receive an interrupt triggered by the main CPU.
|
|
* :example:`system/ulp/lp_core/gpio_intr_pulse_counter` shows how to use GPIO interrupts to count pulses while the main CPU is in Deep-sleep mode.
|
|
|
|
API Reference
|
|
-------------
|
|
|
|
Main CPU API Reference
|
|
~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
.. include-build-file:: inc/ulp_lp_core.inc
|
|
.. include-build-file:: inc/lp_core_i2c.inc
|
|
.. include-build-file:: inc/lp_core_uart.inc
|
|
|
|
.. only:: SOC_LP_SPI_SUPPORTED
|
|
|
|
.. include-build-file:: inc/lp_core_spi.inc
|
|
|
|
.. only:: SOC_LP_CORE_SUPPORT_ETM
|
|
|
|
.. include-build-file:: inc/lp_core_etm.inc
|
|
|
|
.. include-build-file:: inc/lp_core_types.inc
|
|
|
|
LP Core API Reference
|
|
~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
.. include-build-file:: inc/ulp_lp_core_utils.inc
|
|
.. include-build-file:: inc/ulp_lp_core_gpio.inc
|
|
.. include-build-file:: inc/ulp_lp_core_i2c.inc
|
|
.. include-build-file:: inc/ulp_lp_core_uart.inc
|
|
.. include-build-file:: inc/ulp_lp_core_print.inc
|
|
.. include-build-file:: inc/ulp_lp_core_interrupts.inc
|
|
|
|
.. only:: SOC_LP_SPI_SUPPORTED
|
|
|
|
.. include-build-file:: inc/ulp_lp_core_spi.inc
|
|
|
|
.. _esp-idf-monitor: https://github.com/espressif/esp-idf-monitor
|