esp-idf/examples/bluetooth/a2dp_sink
wangmengyang 61bd453c15 component/bt: implement AVRCP Target APIs
1. Add more notification events to the enum according to the event list in AVRCP specification.
2. Add API and callback events for basic AVRCP target functionalities to do init, deinit, callback-registration, connection status indication.
3. Implement API to set/get supported PASSTHROUGH command on local AVRCP TG, implement callback events for remote passthrough command indication.
4. Implement API to set/get supported notification eventIDs on local AVRCP TG, implement API to send event notifications to remote CT. \
   Currently supported event in TG only includes ESP_AVRC_RN_VOLUME_CHANGE(0xd), which can be extended in later commits.
5. Implement callback events for SetAbsoluteVolume command indication on TG.
6. Add limitation of event_ids supported in RegisterNotification command in CT. The supported event_ids include: \
   ESP_AVRC_RN_PLAY_STATUS_CHANGE(0x1), ESP_AVRC_RN_TRACK_CHANGE(0x2), ESP_AVRC_RN_PLAY_POS_CHANGE(0x5), ESP_AVRC_RN_VOLUME_CHANGE(0xd).
7. Add feature bit mask in parameter of callback event ESP_AVRC_CT_REMOTE_FEATURES_EVT for peer feature information got from SDP.
8. Add API and callback event to AVRCP CT to retrieve remote TG's supported notification event capabilities.
9. Modify data type for parameter of callback event ESP_AVRC_CT_CHANGE_NOTIFY_EVT.
10. Change AVRCP version from 1.3 to 1.4 for compatibility cause in using AbsoluteVolume feature.
11. Modify local AVRCP device to be category 1 as CT and category 2 as TG that applies to bluetooth headphones or speakers.
12. Update the use of AVRCP APIs and events in the two examples: a2dp_sink and a2dp_gatts_coex, which include the demo of volume control and notification.
2019-04-10 16:34:13 +08:00
..
main component/bt: implement AVRCP Target APIs 2019-04-10 16:34:13 +08:00
CMakeLists.txt cmake: make main a component again 2018-09-11 09:44:12 +08:00
Makefile remove executable permission from source files 2018-05-29 20:07:45 +08:00
README.md component/bt: fix the format and add more content to A2DP sink example document and source code 2018-08-13 21:17:27 +08:00
sdkconfig.defaults Merge branch 'master' into feature/cmake 2018-08-30 18:51:01 +08:00

ESP-IDF A2DP-SINK demo

Demo of A2DP audio sink role

This is the demo of API implementing Advanced Audio Distribution Profile to receive an audio stream.

This example involves the use of Bluetooth legacy profile A2DP for audio stream reception, AVRCP for media information notifications, and I2S for audio stream output interface.

Applications such as bluetooth speakers can take advantage of this example as a reference of basic functionalities.

How to use this example

Hardware Required

To play the sound, there is a need of loudspeaker and possibly an external I2S codec. Otherwise the example will only show a count of audio data packets received silently. Internal DAC can be selected and in this case external I2S codec may not be needed.

For the I2S codec, pick whatever chip or board works for you; this code was written using a PCM5102 chip, but other I2S boards and chips will probably work as well. The default I2S connections are shown below, but these can be changed in menuconfig:

ESP pin I2S signal
GPIO22 LRCK
GPIO25 DATA
GPIO26 BCK

If the internal DAC is selected, analog audio will be available on GPIO25 and GPIO26. The output resolution on these pins will always be limited to 8 bit because of the internal structure of the DACs.

Configure the project

make menuconfig
  • Set serial port under Serial Flasher Options.

  • Set the use of external I2S codec or internal DAC for audio output, and configure the output PINs under A2DP Example Configuration

  • Enable Classic Bluetooth and A2DP under Component config --> Bluetooth --> Bluedroid Enable

Build and Flash

Build the project and flash it to the board, then run monitor tool to view serial output.

make -j4 flash monitor

(To exit the serial monitor, type Ctrl-].)

Example Output

After the program is started, the example starts inquiry scan and page scan, awaiting being discovered and connected. Other bluetooth devices such as smart phones can discover a device named "ESP_SPEAKER". A smartphone or another ESP-IDF example of A2DP source can be used to connect to the local device.

Once A2DP connection is set up, there will be a notification message with the remote device's bluetooth MAC address like the following:

I (106427) BT_AV: A2DP connection state: Connected, [64:a2:f9:69:57:a4]

If a smartphone is used to connect to local device, starting to play music with an APP will result in the transmission of audio stream. The transmitting of audio stream will be visible in the application log including a count of audio data packets, like this:

I (120627) BT_AV: A2DP audio state: Started
I (122697) BT_AV: Audio packet count 100
I (124697) BT_AV: Audio packet count 200
I (126697) BT_AV: Audio packet count 300
I (128697) BT_AV: Audio packet count 400

Also, the sound will be heard if a loudspeaker is connected and possible external I2S codec is correctly configured. For ESP32 A2DP source example, the sound is noise as the audio source generates the samples with a random sequence.

Troubleshooting

  • For current stage, the supported audio codec in ESP32 A2DP is SBC. SBC data stream is transmitted to A2DP sink and then decoded into PCM samples as output. The PCM data format is normally of 44.1kHz sampling rate, two-channel 16-bit sample stream. Other decoder configurations in ESP32 A2DP sink is supported but need additional modifications of protocol stack settings.
  • As a usage limitation, ESP32 A2DP sink can support at most one connection with remote A2DP source devices. Also, A2DP sink cannot be used together with A2DP source at the same time, but can be used with other profiles such as SPP and HFP.