3.4 KiB
| Supported Targets | ESP32 | ESP32-C2 | ESP32-C3 | ESP32-C5 | ESP32-C6 | ESP32-H2 | ESP32-S3 |
|---|
ESP-IDF BT/BLE HID Device Demo
This demo use APIs which esp_hid component provided to create a BT, BLE or Bluetooth dual mode hid device. Users can choose mode by setting HID_DEV_MODE.
This example works in companion with the BLE HID Host Example
How to Use Example
Before project configuration and build, be sure to set the correct chip target using:
idf.py set-target <chip_name>
The BT hid device plays as a mouse. When the connection is successfully established, users can follow the usage below to operate the 'mouse'.
########################################################################
BT hid mouse demo usage:
You can input these value to simulate mouse: 'q', 'w', 'e', 'a', 's', 'd', 'h'
q -- click the left key
w -- move up
e -- click the right key
a -- move left
s -- move down
d -- move right
h -- show the help
########################################################################
The BLE hid device plays as a remote control. When the connection is successfully established, the remote control will set volume up and down periodically. This example implements a BLE HID device.
Hardware Required
- A development board with ESP32 SoC (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.)
- A USB cable for Power supply and programming
See Development Boards for more information about it.
Configure the Project
Build and Flash
Build the project and flash it to the board, then run monitor tool to view serial output.
idf.py -p PORT flash monitor
(To exit the serial monitor, type Ctrl-].)
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
Example Output
I (0) cpu_start: Starting scheduler on APP CPU.
I (607) BTDM_INIT: BT controller compile version [d03a5d3]
I (607) system_api: Base MAC address is not set
I (607) system_api: read default base MAC address from EFUSE
I (617) phy_init: phy_version 4670,719f9f6,Feb 18 2021,17:07:07
W (1337) BT_BTM: BTM_BleWriteAdvData, Partial data write into ADV
I (1357) HID_DEV_DEMO: START
I (25067) HID_DEV_DEMO: CONNECT
I (25357) HID_DEV_DEMO: Send the volume
E (25437) BT_SMP: Value for numeric comparison = 125657
I (25437) ESP_HID_GAP: BLE GAP NC_REQ passkey:125657
W (25517) BT_SMP: FOR LE SC LTK IS USED INSTEAD OF STK
I (25587) ESP_HID_GAP: BLE GAP KEY type = ESP_LE_KEY_LENC
I (25587) ESP_HID_GAP: BLE GAP KEY type = ESP_LE_KEY_PENC
I (25587) ESP_HID_GAP: BLE GAP KEY type = ESP_LE_KEY_LID
I (25647) ESP_HID_GAP: BLE GAP KEY type = ESP_LE_KEY_PID
I (25757) ESP_HID_GAP: BLE GAP AUTH SUCCESS
I (27457) HID_DEV_DEMO: Send the volume
I (29557) HID_DEV_DEMO: Send the volume
I (31657) HID_DEV_DEMO: Send the volume
I (33757) HID_DEV_DEMO: Send the volume
I (35857) HID_DEV_DEMO: Send the volume
I (37957) HID_DEV_DEMO: Send the volume
I (40057) HID_DEV_DEMO: Send the volume
I (42157) HID_DEV_DEMO: Send the volume
I (44257) HID_DEV_DEMO: Send the volume
I (46357) HID_DEV_DEMO: Send the volume
I (48457) HID_DEV_DEMO: Send the volume
I (50557) HID_DEV_DEMO: Send the volume
...
Troubleshooting
For any technical queries, please open an issue on GitHub. We will get back to you soon.