alex/esp-idf
alex/esp-idf
1
0
Fork 0
mirror of https://github.com/espressif/esp-idf.git synced 2024-10-05 20:47:46 -04:00
Code Issues Actions 2 Packages Projects Releases Wiki Activity
660ff8e840
esp-idf/examples/bluetooth/bluedroid/ble_50/ble50_security_server
History
Marius Vikhammer d2872095f9 soc: moved kconfig options out of the target component. 
Moved the following kconfig options out of the target component:
 * CONFIG_ESP*_DEFAULT_CPU_FREQ* -> esp_system
 * ESP*_REV_MIN -> esp_hw_support
 * ESP*_TIME_SYSCALL -> newlib
 * ESP*_RTC_* -> esp_hw_support

Where applicable these target specific konfig names were merged into
a single common config, e.g;
CONFIG_ESP*_DEFAULT_CPU_FREQ -> CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ
2022-04-21 12:09:43 +08:00
..
main components/bt: Update licenses 2021-12-08 10:59:06 +08:00
tutorial Readme for the bluedroid ble50 example with tutorial of walkthrough example. 2021-11-19 12:04:47 +05:30
CMakeLists.txt component/bt: add BLE v5.0 feature for bluedroid host 2021-01-15 17:55:12 +08:00
README.md Readme for the bluedroid ble50 example with tutorial of walkthrough example. 2021-11-19 12:04:47 +05:30
sdkconfig.defaults soc: moved kconfig options out of the target component. 2022-04-21 12:09:43 +08:00
sdkconfig.defaults.esp32c3 soc: moved kconfig options out of the target component. 2022-04-21 12:09:43 +08:00
sdkconfig.defaults.esp32s3 soc: moved kconfig options out of the target component. 2022-04-21 12:09:43 +08:00

README.md

Supported Targets ESP32-C3 ESP32-S3

ESP-IDF BLE50 Security Server Example

This example shows how to use the APIs to connect in secure manner with peer device and use encryption for data exchange.

To test this example, you can run ble50_security_client_demo, which starts scanning, connects to and starts encryption with ble50_sec_gattc_demo automatically.

Please, check this tutorial for more information about this example.

How to Use Example

Before project configuration and build, be sure to set the correct chip target using:

idf.py set-target <chip_name>

There are some important points for this demo:
1.esp_ble_gap_set_security_param should be used to set the security parameters in the initial stage;
2.esp_ble_set_encryption should be used to start encryption with peer device. If the peer device initiates the encryption, esp_ble_gap_security_rsp should be used to send security response to the peer device when ESP_GAP_BLE_SEC_REQ_EVT is received.
3.The ble50_sec_gattc_demo will receive a ESP_GAP_BLE_AUTH_CMPL_EVT once the encryption procedure has completed.

Hardware Required

  • A development board with ESP32-C3 SoC, ESP32-S3 and BLE5.0 supoorted chips. (e.g., ESP32-C3-DevKitC-1, etc.)
  • A USB cable for Power supply and programming

See Development Boards for more information about it.

Build and Flash

Run idf.py -p PORT flash monitor to build, flash and monitor the project.

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

I (363) BTDM_INIT: BT controller compile version [3e61eea]
I (373) coexist: coexist rom version 8459080
I (373) phy_init: phy_version 500,985899c,Apr 19 2021,16:05:08
I (493) system_api: Base MAC address is not set
I (493) system_api: read default base MAC address from EFUSE
I (493) BTDM_INIT: Bluetooth MAC: 7c:df:a1:40:01:c5

I (503) SEC_GATTS_DEMO: app_main init bluetooth
I (523) SEC_GATTS_DEMO: ESP_GATTS_REG_EVT
I (523) SEC_GATTS_DEMO: The number handle = 8
I (523) SEC_GATTS_DEMO: ESP_GAP_BLE_SET_LOCAL_PRIVACY_COMPLETE_EVT, tatus = 0
I (523) SEC_GATTS_DEMO: ESP_GAP_BLE_EXT_ADV_SET_PARAMS_COMPLETE_EVT status 0
I (533) SEC_GATTS_DEMO: ESP_GAP_BLE_EXT_ADV_DATA_SET_COMPLETE_EVT status 0
I (543) SEC_GATTS_DEMO: ESP_GAP_BLE_EXT_ADV_START_COMPLETE_EVT, status = 0

Troubleshooting

For any technical queries, please open an issue on GitHub. We will get back to you soon.