esp-idf/examples/bluetooth/bluedroid/ble/gatt_security_client
2023-01-10 18:50:25 +08:00
..
main examples: fix ble address type of adv and scan params 2023-01-10 18:50:25 +08:00
tutorial Bluetooth examples restructuring 2019-07-01 19:21:57 +08:00
CMakeLists.txt tools: Increase the minimal supported CMake version to 3.16 2022-06-01 06:35:02 +00:00
README.md esp32h2: renaming esp32h2 to esp32h4 2022-11-08 17:05:33 +08:00
sdkconfig.defaults Update_sdkdefaultconfig_BLE_only_flag ESP32C2 2022-08-09 16:28:01 +00:00
sdkconfig.defaults.esp32c2 Update_sdkdefaultconfig_BLE_only_flag ESP32C2 2022-08-09 16:28:01 +00:00
sdkconfig.defaults.esp32c3 Update_sdkdefaultconfig_BLE_only_flag ESP32C2 2022-08-09 16:28:01 +00:00
sdkconfig.defaults.esp32h4 esp32h2: renaming esp32h2 to esp32h4 2022-11-08 17:05:33 +08:00
sdkconfig.defaults.esp32s3 Update_sdkdefaultconfig_BLE_only_flag ESP32C2 2022-08-09 16:28:01 +00:00

Supported Targets ESP32 ESP32-C2 ESP32-C3 ESP32-H4 ESP32-S3

ESP-IDF Gatt Security Client Example

This example shows how to use the ESP BLE security APIs to secure connect to and encrypt with peer devices.

How to Use Example

Before project configuration and build, be sure to set the correct chip target using:

idf.py set-target <chip_name>

To test this demo, you can run the gatt_security_server_demo, which starts advertising and can be connected to this demo automatically.

There are some important points for this demo:

  1. esp_ble_gap_set_security_param should be used to set the security parameters in the initial stage;
  2. esp_ble_set_encryption should be used to start encryption with peer device. If the peer device initiates the encryption, esp_ble_gap_security_rsp should be used to send security response to the peer device when ESP_GAP_BLE_SEC_REQ_EVT is received.
  3. The gatt_security_client_demo will receive a ESP_GAP_BLE_AUTH_CMPL_EVT once the encryption procedure has completed.

Please, check this tutorial for more information about this example.

Hardware Required

  • A development board with ESP32/ESP32-C3/ESP32-C2/ESP32-H4/ESP32-S3 SoC (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.)
  • A USB cable for Power supply and programming

See Development Boards for more information about it.

Build and Flash

Run idf.py -p PORT flash monitor to build, flash and monitor the project.

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

I (0) cpu_start: Starting scheduler on APP CPU.
I (572) BTDM_INIT: BT controller compile version [1342a48]
I (572) system_api: Base MAC address is not set
I (572) system_api: read default base MAC address from EFUSE
I (582) phy_init: phy_version 4670,719f9f6,Feb 18 2021,17:07:07
I (1002) SEC_GATTC_DEMO: EVT 0, gattc if 1
I (1002) SEC_GATTC_DEMO: REG_EVT
I (1032) SEC_GATTC_DEMO: Scan start success
I (1242) SEC_GATTC_DEMO: 38 68 a4 69 bb 7c
I (1242) SEC_GATTC_DEMO: Searched Adv Data Len 31, Scan Response Len 14
I (1242) SEC_GATTC_DEMO: Searched Device Name Len 0
I (1242) SEC_GATTC_DEMO:

I (1262) SEC_GATTC_DEMO: 38 68 a4 69 bb 7c
I (1262) SEC_GATTC_DEMO: Searched Adv Data Len 31, Scan Response Len 14
I (1262) SEC_GATTC_DEMO: Searched Device Name Len 0
I (1272) SEC_GATTC_DEMO:

I (1592) SEC_GATTC_DEMO: 38 68 a4 69 bb 7c
I (1592) SEC_GATTC_DEMO: Searched Adv Data Len 31, Scan Response Len 14
I (1592) SEC_GATTC_DEMO: Searched Device Name Len 0
I (1602) SEC_GATTC_DEMO:

I (1912) SEC_GATTC_DEMO: 38 68 a4 69 bb 7c
I (1912) SEC_GATTC_DEMO: Searched Adv Data Len 31, Scan Response Len 14
I (1912) SEC_GATTC_DEMO: Searched Device Name Len 0
I (1922) SEC_GATTC_DEMO:

Troubleshooting

For any technical queries, please open an issue on GitHub. We will get back to you soon.