mirror of https://github.com/espressif/esp-idf.git synced 2024-10-05 20:47:46 -04:00

History

Wu Bo Wen 4cbed9b364 driver/adc: support for esp32s2 adc calibration scheme ESP32 lets the user choose from using Vref, Lookup Table, and Two-Point Calibration. In ESP32S2 only two-point calibration is supported. This commit support these changes in idf. Closes https://github.com/espressif/esp-idf/issues/5455		2020-08-17 14:43:41 +08:00
..
main	driver/adc: support for esp32s2 adc calibration scheme	2020-08-17 14:43:41 +08:00
CMakeLists.txt	build_app: make multi target support readable	2020-04-09 16:40:57 +08:00
Makefile	example(adc2): add example and test case for adc2.	2017-10-26 14:35:30 +08:00
README.md	Merge branch 'bugfix/uart_echo_readme' into 'master'	2020-04-11 01:52:01 +08:00

README.md

Supported Targets	ESP32

ADC2 Example

(See the README.md file in the upper level 'examples' directory for more information about examples.)

In this example, we use ADC2 to measure the output of DAC.

How to use example

Hardware Required

ESP32 platform

A development board with ESP32 SoC (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.)
A USB cable for power supply and programming

We use ADC1_CHANNEL_7 (GPIO27) and DAC_CHANNEL_1 (GPIO25) by default, you need to short the two GPIOs (if you have changed the ADC2 and DAC channel, please refer to Chapter 4.11 of the ESP32 Technical Reference Manual to get the pin number).

ESP32-S2 platform

A development board with ESP32S2 SoC
A USB cable for power supply and programming

We use ADC1_CHANNEL_7 (GPIO18) and DAC_CHANNEL_1 (GPIO17) by default, you need to short the two GPIOs (if you have changed the ADC2 and DAC channel, please refer to the ESP32S2 Technical Reference Manual to get the pin number).

Configure the project

idf.py menuconfig

Set ADC2 and DAC channel in "Example Configuration"

Build and Flash

Build the project and flash it to the board, then run monitor tool to view serial output:

idf.py -p PORT flash monitor

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

Running this example, you will see the following log output on the serial monitor:

ESP32 platform

ADC channel 7 @ GPIO 27, DAC channel 1 @ GPIO 25.
adc2_init...
start conversion.
1: 150
2: 203
3: 250
4: 300
5: 351
6: 400
7: 441
8: 491
9: 547
10: 595
...

ESP32-S2 platform

ADC channel 7 @ GPIO 18, DAC channel 1 @ GPIO 17.
adc2_init...
start conversion.
1: 150
2: 203
3: 250
4: 300
5: 351
6: 400
7: 441
8: 491
9: 547
10: 595
...

Troubleshooting

program upload failure
- Hardware connection is not correct: run idf.py -p PORT monitor, and reboot your board to see if there are any output logs.
- The baud rate for downloading is too high: lower your baud rate in the menuconfig menu, and try again.

For any technical queries, please open an issue on GitHub. We will get back to you soon.