mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
145 lines
7.1 KiB
ReStructuredText
145 lines
7.1 KiB
ReStructuredText
Watchdogs
|
|
=========
|
|
|
|
Overview
|
|
--------
|
|
|
|
The ESP-IDF has support for two types of watchdogs: The Interrupt Watchdog Timer
|
|
and the Task Watchdog Timer (TWDT). The Interrupt Watchdog Timer and the TWDT
|
|
can both be enabled using :ref:`project-configuration-menu`, however the TWDT can also be
|
|
enabled during runtime. The Interrupt Watchdog is responsible for detecting
|
|
instances where FreeRTOS task switching is blocked for a prolonged period of
|
|
time. The TWDT is responsible for detecting instances of tasks running without
|
|
yielding for a prolonged period.
|
|
|
|
Interrupt watchdog
|
|
^^^^^^^^^^^^^^^^^^
|
|
|
|
The interrupt watchdog makes sure the FreeRTOS task switching interrupt isn't blocked for a long time. This
|
|
is bad because no other tasks, including potentially important ones like the WiFi task and the idle task,
|
|
can't get any CPU runtime. A blocked task switching interrupt can happen because a program runs into an
|
|
infinite loop with interrupts disabled or hangs in an interrupt.
|
|
|
|
The default action of the interrupt watchdog is to invoke the panic handler. causing a register dump and an opportunity
|
|
for the programmer to find out, using either OpenOCD or gdbstub, what bit of code is stuck with interrupts
|
|
disabled. Depending on the configuration of the panic handler, it can also blindly reset the CPU, which may be
|
|
preferred in a production environment.
|
|
|
|
The interrupt watchdog is built around the hardware watchdog in timer group 1. If this watchdog for
|
|
some reason cannot execute the NMI handler that invokes the panic handler (e.g. because IRAM is
|
|
overwritten by garbage), it will hard-reset the SOC. If the panic handler executes, it will display
|
|
the panic reason as "Interrupt wdt timeout on CPU0" or "Interrupt wdt timeout on CPU1" (as
|
|
applicable).
|
|
|
|
Configuration
|
|
@@@@@@@@@@@@@
|
|
|
|
The interrupt watchdog is enabled by default via the :ref:`CONFIG_ESP_INT_WDT` configuration
|
|
flag. The timeout is configured by setting :ref:`CONFIG_ESP_INT_WDT_TIMEOUT_MS`. The default
|
|
timeout is higher if PSRAM support is enabled, as a critical section or interrupt routine that
|
|
accesses a large amount of PSRAM will take longer to complete in some circumstances. The INT WDT
|
|
timeout should always be longer than the period between FreeRTOS ticks (see
|
|
:ref:`CONFIG_FREERTOS_HZ`).
|
|
|
|
Tuning
|
|
@@@@@@
|
|
|
|
If you find the Interrupt watchdog timeout is triggering because an interrupt or critical section is
|
|
running longer than the timeout period, consider rewriting the code: critical sections should be
|
|
made as short as possible, with non-critical computation happening outside the critical
|
|
section. Interrupt handlers should also perform the minimum possible amount of computation, consider
|
|
pushing data into a queue from the ISR and processing it in a task instead. Neither critical
|
|
sections or interrupt handlers should ever block waiting for another event to occur.
|
|
|
|
If changing the code to reduce the processing time is not possible or desirable, it's possible to
|
|
increase the :ref:`CONFIG_ESP_INT_WDT_TIMEOUT_MS` setting instead.
|
|
|
|
Task Watchdog Timer
|
|
^^^^^^^^^^^^^^^^^^^
|
|
|
|
The Task Watchdog Timer (TWDT) is responsible for detecting instances of tasks
|
|
running for a prolonged period of time without yielding. This is a symptom of
|
|
CPU starvation and is usually caused by a higher priority task looping without
|
|
yielding to a lower-priority task thus starving the lower priority task from
|
|
CPU time. This can be an indicator of poorly written code that spinloops on a
|
|
peripheral, or a task that is stuck in an infinite loop.
|
|
|
|
{IDF_TARGET_IDLE_TASKS:default="Idle task", esp32="Idle Tasks of each CPU"}
|
|
|
|
By default the TWDT will watch the {IDF_TARGET_IDLE_TASKS}, however any task can
|
|
subscribe to be watched by the TWDT. Each watched task must 'reset' the TWDT
|
|
periodically to indicate that they have been allocated CPU time. If a task does
|
|
not reset within the TWDT timeout period, a warning will be printed with
|
|
information about which tasks failed to reset the TWDT in time and which
|
|
tasks are currently running.
|
|
|
|
It is also possible to redefine the function `esp_task_wdt_isr_user_handler`
|
|
in the user code, in order to receive the timeout event and handle it differently.
|
|
|
|
The TWDT is built around the Hardware Watchdog Timer in Timer Group 0. The TWDT
|
|
can be initialized by calling :cpp:func:`esp_task_wdt_init` which will configure
|
|
the hardware timer. A task can then subscribe to the TWDT using
|
|
:cpp:func:`esp_task_wdt_add` in order to be watched. Each subscribed task must
|
|
periodically call :cpp:func:`esp_task_wdt_reset` to reset the TWDT. Failure by
|
|
any subscribed tasks to periodically call :cpp:func:`esp_task_wdt_reset`
|
|
indicates that one or more tasks have been starved of CPU time or are stuck in a
|
|
loop somewhere.
|
|
|
|
A watched task can be unsubscribed from the TWDT using
|
|
:cpp:func:`esp_task_wdt_delete()`. A task that has been unsubscribed should no
|
|
longer call :cpp:func:`esp_task_wdt_reset`. Once all tasks have unsubscribed
|
|
form the TWDT, the TWDT can be deinitialized by calling
|
|
:cpp:func:`esp_task_wdt_deinit()`.
|
|
|
|
The default timeout period for the TWDT is set using config item
|
|
:ref:`CONFIG_ESP_TASK_WDT_TIMEOUT_S`. This should be set to at least as long as you expect any
|
|
single task will need to monopolise the CPU (for example, if you expect the app will do a long
|
|
intensive calculation and should not yield to other tasks). It is also possible to change this
|
|
timeout at runtime by calling :cpp:func:`esp_task_wdt_init`.
|
|
|
|
The following config options control TWDT configuration at startup. They are all enabled by default:
|
|
|
|
{IDF_TARGET_IDLE_TASK:default="Idle task", esp32="CPU0 Idle task"}
|
|
|
|
.. list::
|
|
|
|
- :ref:`CONFIG_ESP_TASK_WDT` - the TWDT is initialized automatically during startup. If this option is disabled, it is still possible to initialize the Task WDT at runtime by calling :cpp:func:`esp_task_wdt_init`.
|
|
- :ref:`CONFIG_ESP_TASK_WDT_CHECK_IDLE_TASK_CPU0` - {IDF_TARGET_IDLE_TASK} is subscribed to the TWDT during startup. If this option is disabled, it is still possible to subscribe the idle task by calling :cpp:func:`esp_task_wdt_add` at any time.
|
|
:esp32: - :ref:`CONFIG_ESP_TASK_WDT_CHECK_IDLE_TASK_CPU1` - CPU1 Idle task is subscribed to the TWDT during startup.
|
|
|
|
|
|
JTAG and watchdogs
|
|
^^^^^^^^^^^^^^^^^^
|
|
|
|
While debugging using OpenOCD, the CPUs will be halted every time a breakpoint
|
|
is reached. However if the watchdog timers continue to run when a breakpoint is
|
|
encountered, they will eventually trigger a reset making it very difficult to
|
|
debug code. Therefore OpenOCD will disable the hardware timers of both the
|
|
interrupt and task watchdogs at every breakpoint. Moreover, OpenOCD will not
|
|
reenable them upon leaving the breakpoint. This means that interrupt watchdog
|
|
and task watchdog functionality will essentially be disabled. No warnings or
|
|
panics from either watchdogs will be generated when the {IDF_TARGET_NAME} is connected to
|
|
OpenOCD via JTAG.
|
|
|
|
|
|
Interrupt Watchdog API Reference
|
|
--------------------------------
|
|
|
|
Header File
|
|
^^^^^^^^^^^
|
|
|
|
* :component_file:`esp_system/include/esp_int_wdt.h`
|
|
|
|
|
|
Functions
|
|
---------
|
|
|
|
.. doxygenfunction:: esp_int_wdt_init
|
|
|
|
Task Watchdog API Reference
|
|
----------------------------
|
|
|
|
A full example using the Task Watchdog is available in esp-idf: :example:`system/task_watchdog`
|
|
|
|
.. include-build-file:: inc/esp_task_wdt.inc
|