esp-idf/examples/system/deep_sleep_wake_stub

Supported Targets	ESP32	ESP32-C3	ESP32-C6	ESP32-S2	ESP32-S3

Deep Sleep Wake Stub Example

(See the README.md file in the upper level 'examples' directory for more information about examples.)

The Deep-sleep wake stub is used to RTC fast boot mode that avoid the SPI flash booting, thus speeding up the wakeup process. This example demonstrates how to implement the wake stub.

In this example, the CONFIG_BOOTLOADER_SKIP_VALIDATE_IN_DEEP_SLEEP Kconfig option is used, which allows you to reduce the boot time of the bootloader during waking up from deep sleep. The bootloader stores in rtc memory the address of a running partition and uses it when it wakes up. This example allows you to skip all image checks and speed up the boot.

How to use example

Hardware Required

This example should be able to run on any commonly available ESP32/ESP32-S2/ESP32-S3/ESP32-C3/ESP32-C6 development board without any extra hardware if only Timer wake up sources are used.

Configure the project

idf.py menuconfig

• Wake up time can be configured via Example configuration > Wake up interval in seconds Wake up sources that are unused or unconnected should be disabled in configuration to prevent inadvertent triggering of wake up as a result of floating pins.

Build and Flash

Build the project and flash it to the board, then run monitor tool to view serial output:

idf.py -p PORT flash monitor

(Replace PORT with the name of the serial port to use.)

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

On initial startup, this example will detect that this is the first boot and output the following log:

...
I (309) cpu_start: Starting scheduler on PRO CPU.
I (0) cpu_start: Starting scheduler on APP CPU.
Not a deep sleep reset
Enabling timer wakeup, 10s
Entering deep sleep

The ESP chips will then enter deep sleep. When a timer wake up occurs, if deep sleep wake stub enabled, the ESP chips will boot from RTC memory and execute stub code. The output log such as the following:

...
ESP-ROM:esp32c6-20220919
Build:Sep 19 2022
rst:0x5 (SLEEP_WAKEUP),boot:0x2c (SPI_FAST_FLASH_BOOT)
wake stub: wakeup count is 1, wakeup cause is 16, wakeup cost 6505 us
wake stub: going to deep sleep
ESP-ROM:esp32c6-20220919
Build:Sep 19 2022
rst:0x5 (SLEEP_WAKEUP),boot:0x2c (SPI_FAST_FLASH_BOOT)
wake stub: wakeup count is 2, wakeup cause is 16, wakeup cost 6506 us
wake stub: going to deep sleep
ESP-ROM:esp32c6-20220919
Build:Sep 19 2022
rst:0x5 (SLEEP_WAKEUP),boot:0x2c (SPI_FAST_FLASH_BOOT)
wake stub: wakeup count is 3, wakeup cause is 16, wakeup cost 6505 us
wake stub: going to deep sleep

Note:

1. The wakeup time cost printed in this example is not accurate, it does not take into account the hardware initialization time before the CPU starts, for most esp chips the initialization time cost is about 280us.

2. And the wake-up time shown in this example is not the optimal wake-up time, because the ROM printing before the wake stub occupies most of the wake-up time, for most esp chips this ROM printing takes about 6100us. In the product firmware, users can temporarily or permanently turn off ROM printing via call esp_deep_sleep_disable_rom_logging or set menuconfig->Boot ROM Behavior->Permanently disable logging to speed up the wake-up time.

3. A method for roughly estimating optimal wake-up time: Taking esp32c6 as example, the wake-up time from stub printing is about 6500us, minus the ROM printing overhead of 6100us, plus the system initialization overhead of 280us, its optimal wake-up overhead is about 680us. Users also can modify the example to configure GPIO wake-up, and obtain a more realistic and accurate wake-up time by grabbing GPIO signals