esp-idf/examples/peripherals/mcpwm/mcpwm_foc_svpwm_open_loop
2023-10-09 12:28:08 +08:00
..
img mcpwm: add foc svpwm generation open loop example 2023-08-01 16:18:19 +08:00
main fix(mcpwm): foc example enable build on all supported target 2023-10-09 12:28:08 +08:00
CMakeLists.txt mcpwm: add foc svpwm generation open loop example 2023-08-01 16:18:19 +08:00
pytest_foc_open_loop.py fix(mcpwm): foc example enable build on all supported target 2023-10-09 12:28:08 +08:00
README.md fix(mcpwm): foc example enable build on all supported target 2023-10-09 12:28:08 +08:00

Supported Targets ESP32 ESP32-C6 ESP32-H2 ESP32-P4 ESP32-S3

MCPWM FOC SVPWM Generation Open Loop Example

Principle

This example shows how to use three pairs of PWM signals to realize FOC (Field-Oriented Control) via the MCPWM peripheral. With the internal dead time submodule, each pair of signals can drive one half-bridge circuit, so that they can be combined to drive a BLDC or PMSM motor, or a three-phase power inverter.

This example realizes an open-loop FOC algorithm to calculate the target voltages for three phases, and then modulates these voltages into three pairs of PWM signals to form the SVPWM signal (or SPWM if build with menu config ESP_FOC_USE_SVPWM off), and finally inputs this SVPWM into six power MOSFETs to get the three-phase power system.

            ┌─────────┐        ┌───────┐     Va
     Vq     │         │ Valpha │       ├──────►
     ──────►│ Inverse ├───────►│       │
            │         │        │ SVPWM │     Vb
     Vd     │         │ Vbeta  │       ├──────►
     ──────►│  Park   ├───────►│       │     Vc
            │         │        │       ├──────►
            └────▲────┘        └───────┘
                 │
                 │theta

The FOC sectors assignment and coord systems are as follow:

Risks

These three-phase sine signals are generated at 50Hz by open loop FOC, please set a proper power supply, or don't let it work for a long time to avoid any potential crash or damages when using it to drive the motor.

How to Use

Hardware Required

  1. An ESP32-S3-Motor-DevKit, or independent circuit module follows: 1.1. Any ESP board with MCPWM peripheral supported (e.g. ESP32S3, ESP32C6, ESP32H2 ,,,) 1.2. A three-phase gate driver, for example, the DRV8302 1.3. Six N-MOSFETs, for example, the IRF540NS
  2. A USB cable for programming
  3. A Power supply at least 9V
  4. Any 3-phases load (e.g. PMSM, ACIM, or transformer)

Connection

Using only delta/triangle connect to the output.

                                               POWER
                                                 │
    ┌────────────────────────┐           ┌───────▼───────┐
    │                  Enable│           │               │
    │                        │           │               │           R1
    │ EXAMPLE_FOC_PWM_UH_GPIO├───────────┤ Bridge Driver │_________┌────┐____
    │                        │           │               │         └────┘    |
    │ EXAMPLE_FOC_PWM_UL_GPIO├───────────┤               │                   |
    │                        │           │     and       │           R2      |neutral line
    │ EXAMPLE_FOC_PWM_VH_GPIO├───────────┤               │_________┌────┐____|
    │                        │           │               │         └────┘    |
    │ EXAMPLE_FOC_PWM_VL_GPIO├───────────┤    MOSFET     │                   |
    │                        │           │               │           R3      |
    │ EXAMPLE_FOC_PWM_WH_GPIO├───────────┤               │_________┌────┐____|
    │                        │           │               │         └────┘
    │ EXAMPLE_FOC_PWM_WL_GPIO├───────────┤               │
    └────────────────────────┘           └───────────────┘

Build and Flash

Select project Kconfig option ESP_FOC_USE_SVPWM by idf.py menuconfig:

  • True: Using SVPWM modem, output saddle wave, the neutral point level is not const zero.
  • False: Using SPWM modem, output standard sin wave, phases and lines level are all sin wave.

Run idf.py -p PORT flash monitor to build, flash and monitor the project.

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

Run the example, you will see the following output log:

...
Hi ESP_SV
I (327) bsp_mcpwm: Disable MOSFET gate
I (337) gpio: GPIO[46]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 0| Pulldown: 0| Intr:0
I (347) bsp_mcpwm: Create MCPWM timer
I (347) bsp_mcpwm: Create MCPWM operator
I (357) bsp_mcpwm: Connect operators to the same timer
I (357) bsp_mcpwm: Create comparators
I (367) bsp_mcpwm: Create PWM generators
I (367) gpio: GPIO[47]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0
I (377) gpio: GPIO[21]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0
I (387) gpio: GPIO[14]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0
I (397) gpio: GPIO[13]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0
I (407) gpio: GPIO[12]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0
I (417) gpio: GPIO[11]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0
I (427) bsp_mcpwm: Set generator actions
I (427) bsp_mcpwm: Setup deadtime
I (437) bsp_mcpwm: Start the MCPWM timer
I (437) bsp_mcpwm: Enable MOSFET gate

If you have an oscilloscope or a logic analyzer, you can see there are 7 segments in one PWM signal and all six PWM signals are center-aligned:

And if you monitor any output after the low-pass filter with the reference of the GROUND, there will be a saddle wave (or sin wave if build with the menu config ESP_FOC_USE_SVPWM off), two of them are as follow:

Do not surprise if you find it is not a sin wave while taking the GROUND as the reference, it is the characteristic of SVPWM modulation, because the voltage of neutral line is not zero for SVPWM. But if you monitor any line-to-line voltage (taking another signal as the reference) in this three-phase power system, you can still get the sin signal:

Please turn off config ESP_FOC_USE_SVPWM if the neutral line is required, then there will be a standard three-phase sin system.