esp-idf/examples/peripherals/spi_slave_hd/append_mode
2022-09-29 02:20:36 +08:00
..
master example: fixed spi_slave_hd and sdio hosts should pull essl package of compatible versions 2022-09-29 02:20:36 +08:00
slave essl: move from esp-idf component to extra component 2022-09-26 12:26:55 +08:00
README.md essl: move from esp-idf component to extra component 2022-09-26 12:26:55 +08:00

SPI Halfduplex Slave Append Mode Example

(See the README.md file in the upper level 'examples' directory for more information about examples.)

This example demonstrates how to use the SPI Slave HD driver and ESSL driver in IDF to communicate: (ESSL driver is an encapsulated layer based on SPI Master driver to communicate with halfduplex mode SPI Slave.)

  • Slave waits for Master to initiate ESSL SPI send and receive request using the SPI Slave HD driver.

  • Slave will continuously prepare TX / RX buffers to the HW for Master to read / write. It will always load its buffer to the HW when the internal queue (see queue_size in spi_slave_hd_slot_config_t) is not full. It doesn't need to wait until a transaction finishes to prepare next buffer to the HW, so as to increase the transaction speed.

  • Master will receive a bunch of packets from the slave for a fixed number of iterations, then send a bunch of packets for a fixed number of iterations.

If you have your own Master, please follow the Espressif ESP32-S2 Technical Reference Manual-SPI Slave Halfduplex for the data format.

Suggest building/flashing/monitoring Slave example first Usually SPI Slave will try to make its buffer ready to be able to respond immediately. In this example, you could run Slave code first to prepare more buffer to the HW. Therefore you will have queue_size number of buffers which are ready for the transaction. And each time there is a vacancy, Slave can load its buffer to the HW.

How to use example

Hardware Required

This example requires 2 targets. Here we use 2 ESP32S2 DevKits to act as the SPI Master and SPI Slave respectively. Suggested pin connections are here:

Signal Master Slave
CS GPIO10 GPIO10
SCLK GPIO12 GPIO12
MOSI GPIO11 GPIO11
MISO GPIO13 GPIO13
GND GND GND

Feel free to modify the pin setting defined on the top of the app_main.c.

Dependency

The master example is based on esp_serial_slave_link component, which is used to communicate to a ESP slave device.

The component can be installed by esp component manager. Since this example already installed it, no need to re-installed it again, but if you want to install this component in your own project, you can input the following command:

idf.py add-dependency espressif/esp_serial_slave_link

If the dependency is added, you can check idf_component.yml for more detail. When building this example or other projects with managed components, the component manager will search for the required components online and download them into the managed_componets folder.

Configure the project

  • Set the target of the build (where {IDF_TARGET} stands for the target chip such as esp32s2).
idf.py set-target {IDF_TARGET}

Build and Flash

For each target, build the project and flash it to the board, then run monitor tool to view the output:

idf.py -p PORT flash monitor

(Replace PORT with the name of the serial port to use.)

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

SPI Master

I (320) Master: Receiver
I (470) Receiver: 8 bytes are actually received:
I (470) Receiver: 21 22 23 24 25 26 27 28
I (560) Receiver: 8 bytes are actually received:
I (560) Receiver: 29 2a 2b 2c 2d 2e 2f 30
I (650) Receiver: 8 bytes are actually received:
I (650) Receiver: 2b 2c 2d 2e 2f 30 31 32
I (740) Receiver: 8 bytes are actually received:
I (740) Receiver: 33 34 35 36 37 38 39 3a
I (830) Receiver: 8 bytes are actually received:
I (830) Receiver: 0c 0d 0e 0f 10 11 12 13
I (920) Receiver: 8 bytes are actually received:
I (920) Receiver: 14 15 16 17 18 19 1a 1b
I (1010) Receiver: 8 bytes are actually received:
I (1010) Receiver: 1d 1e 1f 20 21 22 23 24
I (1100) Receiver: 8 bytes are actually received:
I (1100) Receiver: 25 26 27 28 29 2a 2b 2c
I (1190) Receiver: 8 bytes are actually received:
I (1190) Receiver: 00 01 02 03 04 05 06 07
I (1280) Receiver: 8 bytes are actually received:
I (1280) Receiver: 08 09 0a 0b 0c 0d 0e 0f
I (1280) Master: Sender

SPI Slave

I (6343) Receiver: 16 bytes are actually received:
I (6343) slave RX:: 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f
I (6523) Receiver: 16 bytes are actually received:
I (6523) slave RX:: 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10
I (6703) Receiver: 16 bytes are actually received:
I (6703) slave RX:: 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11
I (6883) Receiver: 16 bytes are actually received:
I (6883) slave RX:: 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12
I (7063) Receiver: 16 bytes are actually received:
I (7063) slave RX:: 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13
I (7243) Receiver: 16 bytes are actually received:
I (7243) slave RX:: 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14
I (7473) Receiver: 16 bytes are actually received:
I (7473) slave RX:: 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15
I (7653) Receiver: 16 bytes are actually received:
I (7653) slave RX:: 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
I (7833) Receiver: 16 bytes are actually received:
I (7833) slave RX:: 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17
I (8013) Receiver: 16 bytes are actually received:
I (8013) slave RX:: 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18