esp-idf/components/soc/esp32/include/hal/i2c_ll.h
houwenxiang aac935ec81 bugfix(i2c): fix I2C driver breaking change issue.
1. Fixed I2C driver breaking change issue.
    2. Add I2C UT test case.
2019-12-04 15:51:36 +08:00

851 lines
22 KiB
C

// Copyright 2015-2019 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// The LL layer for I2C register operations
#pragma once
#include "soc/i2c_periph.h"
#include "hal/i2c_types.h"
/**
* @brief I2C hardware cmd register filed.
*/
typedef union {
struct {
uint32_t byte_num: 8,
ack_en: 1,
ack_exp: 1,
ack_val: 1,
op_code: 3,
reserved14: 17,
done: 1;
};
uint32_t val;
} i2c_hw_cmd_t;
/**
* @brief I2C interrupt event
*/
typedef enum {
I2C_INTR_EVENT_ERR,
I2C_INTR_EVENT_ARBIT_LOST, /*!< I2C arbition lost event */
I2C_INTR_EVENT_NACK, /*!< I2C NACK event */
I2C_INTR_EVENT_TOUT, /*!< I2C time out event */
I2C_INTR_EVENT_END_DET, /*!< I2C end detected event */
I2C_INTR_EVENT_TRANS_DONE, /*!< I2C trans done event */
I2C_INTR_EVENT_RXFIFO_FULL, /*!< I2C rxfifo full event */
I2C_INTR_EVENT_TXFIFO_EMPTY, /*!< I2C txfifo empty event */
} i2c_intr_event_t;
/**
* @brief Data structure for calculating I2C bus timing.
*/
typedef struct {
uint16_t scl_low; /*!< I2C scl low period */
uint16_t scl_high; /*!< I2C scl hight period */
uint16_t sda_hold; /*!< I2C scl low period */
uint16_t sda_sample; /*!< I2C sda sample time */
uint16_t setup; /*!< I2C start and stop condition setup period */
uint16_t hold; /*!< I2C start and stop condition hold period */
uint16_t tout; /*!< I2C bus timeout period */
} i2c_clk_cal_t;
// Get the I2C hardware instance
#define I2C_LL_GET_HW(i2c_num) (((i2c_num) == 0) ? &I2C0 : &I2C1)
// Get the I2C hardware FIFO address
#define I2C_LL_GET_FIFO_ADDR(i2c_num) (I2C_DATA_APB_REG(i2c_num))
// I2C master TX interrupt bitmap
#define I2C_LL_MASTER_TX_INT (I2C_ACK_ERR_INT_ENA_M|I2C_TIME_OUT_INT_ENA_M|I2C_TRANS_COMPLETE_INT_ENA_M|I2C_ARBITRATION_LOST_INT_ENA_M|I2C_END_DETECT_INT_ENA_M)
// I2C master RX interrupt bitmap
#define I2C_LL_MASTER_RX_INT (I2C_TIME_OUT_INT_ENA_M|I2C_TRANS_COMPLETE_INT_ENA_M|I2C_ARBITRATION_LOST_INT_ENA_M|I2C_END_DETECT_INT_ENA_M)
// I2C slave TX interrupt bitmap
#define I2C_LL_SLAVE_TX_INT (I2C_TXFIFO_EMPTY_INT_ENA_M)
// I2C slave RX interrupt bitmap
#define I2C_LL_SLAVE_RX_INT (I2C_RXFIFO_FULL_INT_ENA_M | I2C_TRANS_COMPLETE_INT_ENA_M)
//I2C base clock freq 80M
#define I2C_BASE_CLK_FREQ (80000000)
/**
* @brief Calculate I2C bus frequency
*
* @param source_clk I2C source clock
* @param bus_freq I2C bus frequency
* @param clk_cal Pointer to accept the clock configuration
*
* @return None
*/
static inline void i2c_ll_cal_bus_clk(uint32_t source_clk, uint32_t bus_freq, i2c_clk_cal_t *clk_cal)
{
uint32_t half_cycle = source_clk / bus_freq / 2;
clk_cal->scl_low = half_cycle;
clk_cal->scl_high = half_cycle;
clk_cal->sda_hold = half_cycle / 2;
clk_cal->sda_sample = clk_cal->scl_high / 2;
clk_cal->setup = half_cycle;
clk_cal->hold = half_cycle;
clk_cal->tout = half_cycle * 20; //default we set the timeout value to 10 bus cycles.
}
/**
* @brief Configure the I2C bus timing related register.
*
* @param hw Beginning address of the peripheral registers
* @param bus_cfg Pointer to the data structure holding the register configuration.
*
* @return None
*/
static inline void i2c_ll_set_bus_timing(i2c_dev_t *hw, i2c_clk_cal_t *bus_cfg)
{
//scl period
hw->scl_low_period.period = bus_cfg->scl_low;
hw->scl_high_period.period = bus_cfg->scl_high;
//sda sample
hw->sda_hold.time = bus_cfg->sda_hold;
hw->sda_sample.time = bus_cfg->sda_sample;
//setup
hw->scl_rstart_setup.time = bus_cfg->setup;
hw->scl_stop_setup.time = bus_cfg->setup;
//hold
hw->scl_start_hold.time = bus_cfg->hold;
hw->scl_stop_hold.time = bus_cfg->hold;
hw->timeout.tout = bus_cfg->tout;
}
/**
* @brief Reset I2C txFIFO
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_txfifo_rst(i2c_dev_t *hw)
{
hw->fifo_conf.tx_fifo_rst = 1;
hw->fifo_conf.tx_fifo_rst = 0;
}
/**
* @brief Reset I2C rxFIFO
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_rxfifo_rst(i2c_dev_t *hw)
{
hw->fifo_conf.rx_fifo_rst = 1;
hw->fifo_conf.rx_fifo_rst = 0;
}
/**
* @brief Configure I2C SCL timing
*
* @param hw Beginning address of the peripheral registers
* @param hight_period The I2C SCL hight period (in APB cycle)
* @param low_period The I2C SCL low period (in APB cycle)
*
* @return None.
*/
static inline void i2c_ll_set_scl_timing(i2c_dev_t *hw, int hight_period, int low_period)
{
hw->scl_low_period.period = low_period;
hw->scl_high_period.period = hight_period;
}
/**
* @brief Clear I2C interrupt status
*
* @param hw Beginning address of the peripheral registers
* @param mask Interrupt mask needs to be cleared
*
* @return None
*/
static inline void i2c_ll_clr_intsts_mask(i2c_dev_t *hw, uint32_t mask)
{
hw->int_clr.val = mask;
}
/**
* @brief Enable I2C interrupt
*
* @param hw Beginning address of the peripheral registers
* @param mask Interrupt mask needs to be enabled
*
* @return None
*/
static inline void i2c_ll_enable_intr_mask(i2c_dev_t *hw, uint32_t mask)
{
hw->int_ena.val |= mask;
}
/**
* @brief Disable I2C interrupt
*
* @param hw Beginning address of the peripheral registers
* @param mask Interrupt mask needs to be disabled
*
* @return None
*/
static inline void i2c_ll_disable_intr_mask(i2c_dev_t *hw, uint32_t mask)
{
hw->int_ena.val &= (~mask);
}
/**
* @brief Get I2C interrupt status
*
* @param hw Beginning address of the peripheral registers
*
* @return I2C interrupt status
*/
static inline uint32_t i2c_ll_get_intsts_mask(i2c_dev_t *hw)
{
return hw->int_status.val;
}
/**
* @brief Configure I2C memory access mode, FIFO mode or non-FIFO mode
*
* @param hw Beginning address of the peripheral registers
* @param fifo_mode_en Set true to enable FIFO access mode, else, set it false
*
* @return None
*/
static inline void i2c_ll_set_fifo_mode(i2c_dev_t *hw, bool fifo_mode_en)
{
hw->fifo_conf.nonfifo_en = fifo_mode_en ? 0 : 1;
}
/**
* @brief Configure I2C timeout
*
* @param hw Beginning address of the peripheral registers
* @param tout_num The I2C timeout value needs to be set (in APB cycle)
*
* @return None
*/
static inline void i2c_ll_set_tout(i2c_dev_t *hw, int tout)
{
hw->timeout.tout = tout;
}
/**
* @brief Configure I2C slave address
*
* @param hw Beginning address of the peripheral registers
* @param slave_addr I2C slave address needs to be set
* @param addr_10bit_en Set true to enable 10-bit slave address mode, set false to enable 7-bit address mode
*
* @return None
*/
static inline void i2c_ll_set_slave_addr(i2c_dev_t *hw, uint16_t slave_addr, bool addr_10bit_en)
{
hw->slave_addr.addr = slave_addr;
hw->slave_addr.en_10bit = addr_10bit_en;
}
/**
* @brief Write I2C hardware command register
*
* @param hw Beginning address of the peripheral registers
* @param cmd I2C hardware command
* @param cmd_idx The index of the command register, should be less than 16
*
* @return None
*/
static inline void i2c_ll_write_cmd_reg(i2c_dev_t *hw, i2c_hw_cmd_t cmd, int cmd_idx)
{
hw->command[cmd_idx].val = cmd.val;
}
/**
* @brief Configure I2C start timing
*
* @param hw Beginning address of the peripheral registers
* @param start_setup The start condition setup period (in APB cycle)
* @param start_hold The start condition hold period (in APB cycle)
*
* @return None
*/
static inline void i2c_ll_set_start_timing(i2c_dev_t *hw, int start_setup, int start_hold)
{
hw->scl_rstart_setup.time = start_setup;
hw->scl_start_hold.time = start_hold;
}
/**
* @brief Configure I2C stop timing
*
* @param hw Beginning address of the peripheral registers
* @param stop_setup The stop condition setup period (in APB cycle)
* @param stop_hold The stop condition hold period (in APB cycle)
*
* @return None
*/
static inline void i2c_ll_set_stop_timing(i2c_dev_t *hw, int stop_setup, int stop_hold)
{
hw->scl_stop_setup.time = stop_setup;
hw->scl_stop_hold.time = stop_hold;
}
/**
* @brief Configure I2C stop timing
*
* @param hw Beginning address of the peripheral registers
* @param sda_sample The SDA sample time (in APB cycle)
* @param sda_hold The SDA hold time (in APB cycle)
*
* @return None
*/
static inline void i2c_ll_set_sda_timing(i2c_dev_t *hw, int sda_sample, int sda_hold)
{
hw->sda_hold.time = sda_hold;
hw->sda_sample.time = sda_sample;
}
/**
* @brief Set I2C txFIFO empty threshold
*
* @param hw Beginning address of the peripheral registers
* @param empty_thr The txFIFO empty threshold
*
* @return None
*/
static inline void i2c_ll_set_txfifo_empty_thr(i2c_dev_t *hw, uint8_t empty_thr)
{
hw->fifo_conf.tx_fifo_empty_thrhd = empty_thr;
}
/**
* @brief Set I2C rxFIFO full threshold
*
* @param hw Beginning address of the peripheral registers
* @param full_thr The rxFIFO full threshold
*
* @return None
*/
static inline void i2c_ll_set_rxfifo_full_thr(i2c_dev_t *hw, uint8_t full_thr)
{
hw->fifo_conf.rx_fifo_full_thrhd = full_thr;
}
/**
* @brief Set the I2C data mode, LSB or MSB
*
* @param hw Beginning address of the peripheral registers
* @param tx_mode Tx data bit mode
* @param rx_mode Rx data bit mode
*
* @return None
*/
static inline void i2c_ll_set_data_mode(i2c_dev_t *hw, i2c_trans_mode_t tx_mode, i2c_trans_mode_t rx_mode)
{
hw->ctr.tx_lsb_first = tx_mode;
hw->ctr.rx_lsb_first = rx_mode;
}
/**
* @brief Get the I2C data mode
*
* @param hw Beginning address of the peripheral registers
* @param tx_mode Pointer to accept the received bytes mode
* @param rx_mode Pointer to accept the sended bytes mode
*
* @return None
*/
static inline void i2c_ll_get_data_mode(i2c_dev_t *hw, i2c_trans_mode_t *tx_mode, i2c_trans_mode_t *rx_mode)
{
*tx_mode = hw->ctr.tx_lsb_first;
*rx_mode = hw->ctr.rx_lsb_first;
}
/**
* @brief Get I2C sda timing configuration
*
* @param hw Beginning address of the peripheral registers
* @param sda_sample Pointer to accept the SDA sample timing configuration
* @param sda_hold Pointer to accept the SDA hold timing configuration
*
* @return None
*/
static inline void i2c_ll_get_sda_timing(i2c_dev_t *hw, int *sda_sample, int *sda_hold)
{
*sda_hold = hw->sda_hold.time;
*sda_sample = hw->sda_sample.time;
}
/**
* @brief Get the I2C hardware version
*
* @param hw Beginning address of the peripheral registers
*
* @return The I2C hardware version
*/
static inline uint32_t i2c_ll_get_hw_version(i2c_dev_t *hw)
{
return hw->date;
}
/**
* @brief Check if the I2C bus is busy
*
* @param hw Beginning address of the peripheral registers
*
* @return True if I2C state machine is busy, else false will be returned
*/
static inline bool i2c_ll_is_bus_busy(i2c_dev_t *hw)
{
return hw->status_reg.bus_busy;
}
/**
* @brief Check if I2C is master mode
*
* @param hw Beginning address of the peripheral registers
*
* @return True if I2C is master mode, else false will be returned
*/
static inline bool i2c_ll_is_master_mode(i2c_dev_t *hw)
{
return hw->ctr.ms_mode;
}
/**
* @brief Get the rxFIFO readable length
*
* @param hw Beginning address of the peripheral registers
*
* @return RxFIFO readable length
*/
static inline uint32_t i2c_ll_get_rxfifo_cnt(i2c_dev_t *hw)
{
return hw->status_reg.rx_fifo_cnt;
}
/**
* @brief Get I2C txFIFO writable length
*
* @param hw Beginning address of the peripheral registers
*
* @return TxFIFO writable length
*/
static inline uint32_t i2c_ll_get_txfifo_len(i2c_dev_t *hw)
{
return SOC_I2C_FIFO_LEN - hw->status_reg.tx_fifo_cnt;
}
/**
* @brief Get I2C timeout configuration
*
* @param hw Beginning address of the peripheral registers
*
* @return The I2C timeout value
*/
static inline uint32_t i2c_ll_get_tout(i2c_dev_t *hw)
{
return hw->timeout.tout;
}
/**
* @brief Start I2C transfer
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_trans_start(i2c_dev_t *hw)
{
hw->ctr.trans_start = 1;
}
/**
* @brief Get I2C start timing configuration
*
* @param hw Beginning address of the peripheral registers
* @param setup_time Pointer to accept the start condition setup period
* @param hold_time Pointer to accept the start condition hold period
*
* @return None
*/
static inline void i2c_ll_get_start_timing(i2c_dev_t *hw, int *setup_time, int *hold_time)
{
*setup_time = hw->scl_rstart_setup.time;
*hold_time = hw->scl_start_hold.time;
}
/**
* @brief Get I2C stop timing configuration
*
* @param hw Beginning address of the peripheral registers
* @param setup_time Pointer to accept the stop condition setup period
* @param hold_time Pointer to accept the stop condition hold period
*
* @return None
*/
static inline void i2c_ll_get_stop_timing(i2c_dev_t *hw, int *setup_time, int *hold_time)
{
*setup_time = hw->scl_stop_setup.time;
*hold_time = hw->scl_stop_hold.time;
}
/**
* @brief Get I2C SCL timing configuration
*
* @param hw Beginning address of the peripheral registers
* @param high_period Pointer to accept the SCL high period
* @param low_period Pointer to accept the SCL low period
*
* @return None
*/
static inline void i2c_ll_get_scl_timing(i2c_dev_t *hw, int *high_period, int *low_period)
{
*high_period = hw->scl_high_period.period;
*low_period = hw->scl_low_period.period;
}
/**
* @brief Write the I2C hardware txFIFO
*
* @param hw Beginning address of the peripheral registers
* @param ptr Pointer to data buffer
* @param len Amount of data needs to be writen
*
* @return None.
*/
static inline void i2c_ll_write_txfifo(i2c_dev_t *hw, uint8_t *ptr, uint8_t len)
{
uint32_t fifo_addr = (hw == &I2C0) ? 0x6001301c : 0x6002701c;
for(int i = 0; i < len; i++) {
WRITE_PERI_REG(fifo_addr, ptr[i]);
}
}
/**
* @brief Read the I2C hardware rxFIFO
*
* @param hw Beginning address of the peripheral registers
* @param ptr Pointer to data buffer
* @param len Amount of data needs read
*
* @return None
*/
static inline void i2c_ll_read_rxfifo(i2c_dev_t *hw, uint8_t *ptr, uint8_t len)
{
for(int i = 0; i < len; i++) {
ptr[i] = hw->fifo_data.data;
}
}
/**
* @brief Configure I2C hardware filter
*
* @param hw Beginning address of the peripheral registers
* @param filter_num If the glitch period on the line is less than this value, it can be filtered out
* If `filter_num == 0`, the filter will be disabled
*
* @return None
*/
static inline void i2c_ll_set_filter(i2c_dev_t *hw, uint8_t filter_num)
{
if(filter_num > 0) {
hw->scl_filter_cfg.thres = filter_num;
hw->sda_filter_cfg.thres = filter_num;
hw->scl_filter_cfg.en = 1;
hw->sda_filter_cfg.en = 1;
} else {
hw->scl_filter_cfg.en = 0;
hw->sda_filter_cfg.en = 0;
}
}
/**
* @brief Get I2C hardware filter configuration
*
* @param hw Beginning address of the peripheral registers
*
* @return The hardware filter configuration
*/
static inline uint8_t i2c_ll_get_filter(i2c_dev_t *hw)
{
return hw->sda_filter_cfg.thres;
}
/**
* @brief Enable I2C master TX interrupt
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_master_enable_tx_it(i2c_dev_t *hw)
{
hw->int_clr.val = ~0;
hw->int_ena.val = I2C_LL_MASTER_TX_INT;
}
/**
* @brief Enable I2C master RX interrupt
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_master_enable_rx_it(i2c_dev_t *hw)
{
hw->int_clr.val = ~0;
hw->int_ena.val = I2C_LL_MASTER_RX_INT;
}
/**
* @brief Disable I2C master TX interrupt
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_master_disable_tx_it(i2c_dev_t *hw)
{
hw->int_ena.val &= (~I2C_LL_MASTER_TX_INT);
}
/**
* @brief Disable I2C master RX interrupt
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_master_disable_rx_it(i2c_dev_t *hw)
{
hw->int_ena.val &= (~I2C_LL_MASTER_RX_INT);
}
/**
* @brief Clear I2C master TX interrupt status register
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_master_clr_tx_it(i2c_dev_t *hw)
{
hw->int_clr.val = I2C_LL_MASTER_TX_INT;
}
/**
* @brief Clear I2C master RX interrupt status register
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_master_clr_rx_it(i2c_dev_t *hw)
{
hw->int_clr.val = I2C_LL_MASTER_RX_INT;
}
/**
* @brief
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_slave_enable_tx_it(i2c_dev_t *hw)
{
hw->int_ena.val |= I2C_LL_SLAVE_TX_INT;
}
/**
* @brief Enable I2C slave RX interrupt
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_slave_enable_rx_it(i2c_dev_t *hw)
{
hw->int_ena.val |= I2C_LL_SLAVE_RX_INT;
}
/**
* @brief Disable I2C slave TX interrupt
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_slave_disable_tx_it(i2c_dev_t *hw)
{
hw->int_ena.val &= (~I2C_LL_SLAVE_TX_INT);
}
/**
* @brief Disable I2C slave RX interrupt
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_slave_disable_rx_it(i2c_dev_t *hw)
{
hw->int_ena.val &= (~I2C_LL_SLAVE_RX_INT);
}
/**
* @brief Clear I2C slave TX interrupt status register
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_slave_clr_tx_it(i2c_dev_t *hw)
{
hw->int_clr.val = I2C_LL_SLAVE_TX_INT;
}
/**
* @brief Clear I2C slave RX interrupt status register.
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_slave_clr_rx_it(i2c_dev_t *hw)
{
hw->int_clr.val = I2C_LL_SLAVE_RX_INT;
}
/**
* @brief Reste I2C master FSM. When the master FSM is stuck, call this function to reset the FSM
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_master_fsm_rst(i2c_dev_t *hw)
{
;//ESP32 do not support
}
/**
* @brief Clear I2C bus, when the slave is stuck in a deadlock and keeps pulling the bus low,
* master can controls the SCL bus to generate 9 CLKs.
*
* Note: The master cannot detect if deadlock happens, but when the scl_st_to interrupt is generated, a deadlock may occur.
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_master_clr_bus(i2c_dev_t *hw)
{
;//ESP32 do not support
}
/**
* @brief Set I2C source clock
*
* @param hw Beginning address of the peripheral registers
* @param src_clk Source clock of the I2C
*
* @return None
*/
static inline void i2c_ll_set_source_clk(i2c_dev_t *hw, i2c_sclk_t src_clk)
{
;//Not support on ESP32
}
/**
* @brief Get I2C master interrupt event
*
* @param hw Beginning address of the peripheral registers
* @param event Pointer to accept the interrupt event
*
* @return None
*/
static inline void i2c_ll_master_get_event(i2c_dev_t *hw, i2c_intr_event_t *event)
{
typeof(hw->int_status) int_sts = hw->int_status;
if (int_sts.arbitration_lost) {
*event = I2C_INTR_EVENT_ARBIT_LOST;
} else if (int_sts.ack_err) {
*event = I2C_INTR_EVENT_NACK;
} else if (int_sts.time_out) {
*event = I2C_INTR_EVENT_TOUT;
} else if (int_sts.end_detect) {
*event = I2C_INTR_EVENT_END_DET;
} else if (int_sts.trans_complete) {
*event = I2C_INTR_EVENT_TRANS_DONE;
} else {
*event = I2C_INTR_EVENT_ERR;
}
}
/**
* @brief Get I2C slave interrupt event
*
* @param hw Beginning address of the peripheral registers
* @param event Pointer to accept the interrupt event
*
* @return None
*/
static inline void i2c_ll_slave_get_event(i2c_dev_t *hw, i2c_intr_event_t *event)
{
typeof(hw->int_status) int_sts = hw->int_status;
if (int_sts.tx_fifo_empty) {
*event = I2C_INTR_EVENT_TXFIFO_EMPTY;
} else if (int_sts.trans_complete) {
*event = I2C_INTR_EVENT_TRANS_DONE;
} else if (int_sts.rx_fifo_full) {
*event = I2C_INTR_EVENT_RXFIFO_FULL;
} else {
*event = I2C_INTR_EVENT_ERR;
}
}
/**
* @brief Init I2C master
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_master_init(i2c_dev_t *hw)
{
typeof(hw->ctr) ctrl_reg;
ctrl_reg.val = 0;
ctrl_reg.ms_mode = 1;
ctrl_reg.sda_force_out = 1;
ctrl_reg.scl_force_out = 1;
hw->ctr.val = ctrl_reg.val;
}
/**
* @brief Init I2C slave
*
* @param hw Beginning address of the peripheral registers
*
* @return None
*/
static inline void i2c_ll_slave_init(i2c_dev_t *hw)
{
typeof(hw->ctr) ctrl_reg;
ctrl_reg.val = 0;
ctrl_reg.sda_force_out = 1;
ctrl_reg.scl_force_out = 1;
hw->ctr.val = ctrl_reg.val;
hw->fifo_conf.fifo_addr_cfg_en = 0;
}