esp-idf/components/driver/Kconfig
2022-10-25 17:14:59 +08:00

449 lines
21 KiB
Plaintext

menu "Driver Configurations"
menu "Legacy ADC Configuration"
config ADC_DISABLE_DAC
depends on SOC_DAC_SUPPORTED
bool "Disable DAC when ADC2 is used on GPIO 25 and 26"
default y
help
If this is set, the ADC2 driver will disable the output of the DAC corresponding to the specified
channel. This is the default value.
For testing, disable this option so that we can measure the output of DAC by internal ADC.
config ADC_SUPPRESS_DEPRECATE_WARN
bool "Suppress legacy driver deprecated warning"
default n
help
Wether to suppress the deprecation warnings when using legacy adc driver (driver/adc.h).
If you want to continue using the legacy driver, and don't want to see related deprecation warnings,
you can enable this option.
menu "Legacy ADC Calibration Configuration"
config ADC_CAL_EFUSE_TP_ENABLE
depends on IDF_TARGET_ESP32
bool "Use Two Point Values"
default "y"
help
Some ESP32s have Two Point calibration values burned into eFuse BLOCK3.
This option will allow the ADC calibration component to characterize the
ADC-Voltage curve using Two Point values if they are available.
config ADC_CAL_EFUSE_VREF_ENABLE
depends on IDF_TARGET_ESP32
bool "Use eFuse Vref"
default "y"
help
Some ESP32s have Vref burned into eFuse BLOCK0. This option will allow
the ADC calibration component to characterize the ADC-Voltage curve using
eFuse Vref if it is available.
config ADC_CAL_LUT_ENABLE
depends on IDF_TARGET_ESP32
bool "Use Lookup Tables"
default "y"
help
This option will allow the ADC calibration component to use Lookup Tables
to correct for non-linear behavior in 11db attenuation. Other attenuations
do not exhibit non-linear behavior hence will not be affected by this option.
config ADC_CALI_SUPPRESS_DEPRECATE_WARN
bool "Suppress legacy driver deprecated warning"
default n
help
Wether to suppress the deprecation warnings when using legacy adc calibration
driver (esp_adc_cal.h).
If you want to continue using the legacy driver, and don't want to see related
deprecation warnings, you can enable this option.
endmenu
endmenu # ADC Configuration
menu "SPI Configuration"
config SPI_MASTER_IN_IRAM
bool "Place transmitting functions of SPI master into IRAM"
default n
select SPI_MASTER_ISR_IN_IRAM
help
Normally only the ISR of SPI master is placed in the IRAM, so that it
can work without the flash when interrupt is triggered.
For other functions, there's some possibility that the flash cache
miss when running inside and out of SPI functions, which may increase
the interval of SPI transactions.
Enable this to put ``queue_trans``, ``get_trans_result`` and
``transmit`` functions into the IRAM to avoid possible cache miss.
During unit test, this is enabled to measure the ideal case of api.
config SPI_MASTER_ISR_IN_IRAM
bool "Place SPI master ISR function into IRAM"
default y
help
Place the SPI master ISR in to IRAM to avoid possible cache miss.
Also you can forbid the ISR being disabled during flash writing
access, by add ESP_INTR_FLAG_IRAM when initializing the driver.
config SPI_SLAVE_IN_IRAM
bool "Place transmitting functions of SPI slave into IRAM"
default n
select SPI_SLAVE_ISR_IN_IRAM
help
Normally only the ISR of SPI slave is placed in the IRAM, so that it
can work without the flash when interrupt is triggered.
For other functions, there's some possibility that the flash cache
miss when running inside and out of SPI functions, which may increase
the interval of SPI transactions.
Enable this to put ``queue_trans``, ``get_trans_result`` and
``transmit`` functions into the IRAM to avoid possible cache miss.
config SPI_SLAVE_ISR_IN_IRAM
bool "Place SPI slave ISR function into IRAM"
default y
help
Place the SPI slave ISR in to IRAM to avoid possible cache miss.
Also you can forbid the ISR being disabled during flash writing
access, by add ESP_INTR_FLAG_IRAM when initializing the driver.
endmenu # SPI Configuration
menu "TWAI Configuration"
depends on SOC_TWAI_SUPPORTED
config TWAI_ISR_IN_IRAM
bool "Place TWAI ISR function into IRAM"
default n
select PERIPH_CTRL_FUNC_IN_IRAM if TWAI_ERRATA_FIX_RX_FRAME_INVALID || TWAI_ERRATA_FIX_RX_FIFO_CORRUPT
help
Place the TWAI ISR in to IRAM. This will allow the ISR to avoid
cache misses, and also be able to run whilst the cache is disabled
(such as when writing to SPI Flash).
Note that if this option is enabled:
- Users should also set the ESP_INTR_FLAG_IRAM in the driver
configuration structure when installing the driver (see docs for
specifics).
- Alert logging (i.e., setting of the TWAI_ALERT_AND_LOG flag)
will have no effect.
config TWAI_ERRATA_FIX_BUS_OFF_REC
bool "Add SW workaround for REC change during bus-off"
depends on IDF_TARGET_ESP32
default y
help
When the bus-off condition is reached, the REC should be reset to 0 and frozen (via LOM) by the
driver's ISR. However on the ESP32, there is an edge case where the REC will increase before the
driver's ISR can respond in time (e.g., due to the rapid occurrence of bus errors), thus causing the
REC to be non-zero after bus-off. A non-zero REC can prevent bus-off recovery as the bus-off recovery
condition is that both TEC and REC become 0. Enabling this option will add a workaround in the driver
to forcibly reset REC to zero on reaching bus-off.
config TWAI_ERRATA_FIX_TX_INTR_LOST
bool "Add SW workaround for TX interrupt lost errata"
depends on IDF_TARGET_ESP32
default y
help
On the ESP32, when a transmit interrupt occurs, and interrupt register is read on the same APB clock
cycle, the transmit interrupt could be lost. Enabling this option will add a workaround that checks the
transmit buffer status bit to recover any lost transmit interrupt.
config TWAI_ERRATA_FIX_RX_FRAME_INVALID
bool "Add SW workaround for invalid RX frame errata"
depends on IDF_TARGET_ESP32
default y
help
On the ESP32, when receiving a data or remote frame, if a bus error occurs in the data or CRC field,
the data of the next received frame could be invalid. Enabling this option will add a workaround that
will reset the peripheral on detection of this errata condition. Note that if a frame is transmitted on
the bus whilst the reset is ongoing, the message will not be receive by the peripheral sent on the bus
during the reset, the message will be lost.
config TWAI_ERRATA_FIX_RX_FIFO_CORRUPT
bool "Add SW workaround for RX FIFO corruption errata"
depends on IDF_TARGET_ESP32
default y
help
On the ESP32, when the RX FIFO overruns and the RX message counter maxes out at 64 messages, the entire
RX FIFO is no longer recoverable. Enabling this option will add a workaround that resets the peripheral
on detection of this errata condition. Note that if a frame is being sent on the bus during the reset
bus during the reset, the message will be lost.
endmenu # TWAI Configuration
menu "Temperature sensor Configuration"
depends on SOC_TEMP_SENSOR_SUPPORTED
config TEMP_SENSOR_SUPPRESS_DEPRECATE_WARN
bool "Suppress legacy driver deprecated warning"
default n
help
Wether to suppress the deprecation warnings when using legacy temperature sensor driver
(driver/temp_sensor.h). If you want to continue using the legacy driver,
and don't want to see related deprecation warnings, you can enable this option.
config TEMP_SENSOR_ENABLE_DEBUG_LOG
bool "Enable debug log"
default n
help
Wether to enable the debug log message for temperature sensor driver.
Note that, this option only controls the temperature sensor driver log, won't affect other drivers.
endmenu # TEMP_SENSOR Configuration
menu "UART Configuration"
config UART_ISR_IN_IRAM
bool "Place UART ISR function into IRAM"
depends on !RINGBUF_PLACE_ISR_FUNCTIONS_INTO_FLASH
default n
help
If this option is not selected, UART interrupt will be disabled for a long time and
may cause data lost when doing spi flash operation.
endmenu # UART Configuration
menu "GPIO Configuration"
config GPIO_ESP32_SUPPORT_SWITCH_SLP_PULL
bool "Support light sleep GPIO pullup/pulldown configuration for ESP32"
depends on IDF_TARGET_ESP32
help
This option is intended to fix the bug that ESP32 is not able to switch to configured
pullup/pulldown mode in sleep.
If this option is selected, chip will automatically emulate the behaviour of switching,
and about 450B of source codes would be placed into IRAM.
config GPIO_CTRL_FUNC_IN_IRAM
bool "Place GPIO control functions into IRAM"
default n
help
Place GPIO control functions (like intr_disable/set_level) into IRAM,
so that these functions can be IRAM-safe and able to be called in the other IRAM interrupt context.
endmenu # GPIO Configuration
menu "Sigma Delta Modulator Configuration"
depends on SOC_SDM_SUPPORTED
config SDM_CTRL_FUNC_IN_IRAM
bool "Place SDM control functions into IRAM"
default n
help
Place SDM control functions (like set_duty) into IRAM,
so that these functions can be IRAM-safe and able to be called in the other IRAM interrupt context.
Enabling this option can improve driver performance as well.
config SDM_SUPPRESS_DEPRECATE_WARN
bool "Suppress legacy driver deprecated warning"
default n
help
Wether to suppress the deprecation warnings when using legacy sigma delta driver.
If you want to continue using the legacy driver, and don't want to see related deprecation warnings,
you can enable this option.
config SDM_ENABLE_DEBUG_LOG
bool "Enable debug log"
default n
help
Wether to enable the debug log message for SDM driver.
Note that, this option only controls the SDM driver log, won't affect other drivers.
endmenu # Sigma Delta Modulator Configuration
menu "GPTimer Configuration"
config GPTIMER_CTRL_FUNC_IN_IRAM
bool "Place GPTimer control functions into IRAM"
default n
help
Place GPTimer control functions (like start/stop) into IRAM,
so that these functions can be IRAM-safe and able to be called in the other IRAM interrupt context.
Enabling this option can improve driver performance as well.
config GPTIMER_ISR_IRAM_SAFE
bool "GPTimer ISR IRAM-Safe"
default n
help
Ensure the GPTimer interrupt is IRAM-Safe by allowing the interrupt handler to be
executable when the cache is disabled (e.g. SPI Flash write).
config GPTIMER_SUPPRESS_DEPRECATE_WARN
bool "Suppress legacy driver deprecated warning"
default n
help
Wether to suppress the deprecation warnings when using legacy timer group driver (driver/timer.h).
If you want to continue using the legacy driver, and don't want to see related deprecation warnings,
you can enable this option.
config GPTIMER_ENABLE_DEBUG_LOG
bool "Enable debug log"
default n
help
Wether to enable the debug log message for GPTimer driver.
Note that, this option only controls the GPTimer driver log, won't affect other drivers.
endmenu # GPTimer Configuration
menu "PCNT Configuration"
depends on SOC_PCNT_SUPPORTED
config PCNT_CTRL_FUNC_IN_IRAM
bool "Place PCNT control functions into IRAM"
default n
help
Place PCNT control functions (like start/stop) into IRAM,
so that these functions can be IRAM-safe and able to be called in the other IRAM interrupt context.
Enabling this option can improve driver performance as well.
config PCNT_ISR_IRAM_SAFE
bool "PCNT ISR IRAM-Safe"
default n
help
Ensure the PCNT interrupt is IRAM-Safe by allowing the interrupt handler to be
executable when the cache is disabled (e.g. SPI Flash write).
config PCNT_SUPPRESS_DEPRECATE_WARN
bool "Suppress legacy driver deprecated warning"
default n
help
Wether to suppress the deprecation warnings when using legacy PCNT driver (driver/pcnt.h).
If you want to continue using the legacy driver, and don't want to see related deprecation warnings,
you can enable this option.
config PCNT_ENABLE_DEBUG_LOG
bool "Enable debug log"
default n
help
Wether to enable the debug log message for PCNT driver.
Note that, this option only controls the PCNT driver log, won't affect other drivers.
endmenu # PCNT Configuration
menu "RMT Configuration"
depends on SOC_RMT_SUPPORTED
config RMT_ISR_IRAM_SAFE
bool "RMT ISR IRAM-Safe"
default n
select GDMA_ISR_IRAM_SAFE if SOC_RMT_SUPPORT_DMA # RMT basic functionality relies on GDMA callback
select GDMA_CTRL_FUNC_IN_IRAM if SOC_RMT_SUPPORT_DMA # RMT needs to restart the GDMA in the interrupt
help
Ensure the RMT interrupt is IRAM-Safe by allowing the interrupt handler to be
executable when the cache is disabled (e.g. SPI Flash write).
config RMT_SUPPRESS_DEPRECATE_WARN
bool "Suppress legacy driver deprecated warning"
default n
help
Wether to suppress the deprecation warnings when using legacy rmt driver (driver/rmt.h).
If you want to continue using the legacy driver, and don't want to see related deprecation warnings,
you can enable this option.
config RMT_ENABLE_DEBUG_LOG
bool "Enable debug log"
default n
help
Wether to enable the debug log message for RMT driver.
Note that, this option only controls the RMT driver log, won't affect other drivers.
endmenu # RMT Configuration
menu "MCPWM Configuration"
depends on SOC_MCPWM_SUPPORTED
config MCPWM_ISR_IRAM_SAFE
bool "Place MCPWM ISR function into IRAM"
default n
help
This will ensure the MCPWM interrupt handle is IRAM-Safe, allow to avoid flash
cache misses, and also be able to run whilst the cache is disabled.
(e.g. SPI Flash write)
config MCPWM_CTRL_FUNC_IN_IRAM
bool "Place MCPWM control functions into IRAM"
default n
help
Place MCPWM control functions (like set_compare_value) into IRAM,
so that these functions can be IRAM-safe and able to be called in the other IRAM interrupt context.
Enabling this option can improve driver performance as well.
config MCPWM_SUPPRESS_DEPRECATE_WARN
bool "Suppress leagcy driver deprecated warning"
default n
help
Wether to suppress the deprecation warnings when using legacy MCPWM driver (driver/mcpwm.h).
If you want to continue using the legacy driver, and don't want to see related deprecation warnings,
you can enable this option.
config MCPWM_ENABLE_DEBUG_LOG
bool "Enable debug log"
default n
help
Wether to enable the debug log message for MCPWM driver.
Note that, this option only controls the MCPWM driver log, won't affect other drivers.
endmenu # MCPWM Configuration
menu "I2S Configuration"
depends on SOC_I2S_SUPPORTED
config I2S_ISR_IRAM_SAFE
bool "I2S ISR IRAM-Safe"
default n
help
Ensure the I2S interrupt is IRAM-Safe by allowing the interrupt handler to be
executable when the cache is disabled (e.g. SPI Flash write).
config I2S_SUPPRESS_DEPRECATE_WARN
bool "Suppress leagcy driver deprecated warning"
default n
help
Enable this option will suppress the deprecation warnings of using APIs in legacy I2S driver.
config I2S_ENABLE_DEBUG_LOG
bool "Enable I2S debug log"
default n
help
Wether to enable the debug log message for I2S driver.
Note that, this option only controls the I2S driver log, will not affect other drivers.
endmenu # I2S Configuration
menu "DAC Configuration"
depends on SOC_DAC_SUPPORTED
config DAC_CTRL_FUNC_IN_IRAM
bool "Place DAC control functions into IRAM"
default n
help
Place DAC control functions (e.g. 'dac_oneshot_output_voltage') into IRAM,
so that this function can be IRAM-safe and able to be called in the other IRAM interrupt context.
Enabling this option can improve driver performance as well.
config DAC_ISR_IRAM_SAFE
bool "DAC ISR IRAM-Safe"
default n
help
Ensure the DAC interrupt is IRAM-Safe by allowing the interrupt handler to be
executable when the cache is disabled (e.g. SPI Flash write).
config DAC_SUPPRESS_DEPRECATE_WARN
bool "Suppress legacy driver deprecated warning"
default n
help
Wether to suppress the deprecation warnings when using legacy DAC driver (driver/dac.h).
If you want to continue using the legacy driver, and don't want to see related deprecation warnings,
you can enable this option.
config DAC_ENABLE_DEBUG_LOG
bool "Enable debug log"
default n
help
Wether to enable the debug log message for DAC driver.
Note that, this option only controls the DAC driver log, won't affect other drivers.
config DAC_DMA_AUTO_16BIT_ALIGN
bool "Align the continuous data to 16 bit automatically"
depends on SOC_DAC_DMA_16BIT_ALIGN
default y
help
Whether to left shift the continuous data to align every bytes to 16 bits in the driver.
On ESP32, although the DAC resolution is only 8 bits,
the hardware requires 16 bits data in continuous mode.
By enabling this option, the driver will left shift 8 bits for the input data automatically.
Only disable this option when you decide to do this step by yourself.
Note that the driver will allocate a new piece of memory to save the converted data.
endmenu # DAC Configuration
endmenu # Driver configurations