mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
67 lines
2.5 KiB
Markdown
67 lines
2.5 KiB
Markdown
| Supported Targets | ESP32 | ESP32-C2 | ESP32-C3 | ESP32-C5 | ESP32-C6 | ESP32-C61 | ESP32-H2 | ESP32-P4 | ESP32-S2 | ESP32-S3 |
|
|
| ----------------- | ----- | -------- | -------- | -------- | -------- | --------- | -------- | -------- | -------- | -------- |
|
|
|
|
# _LEDC Fade Example_
|
|
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
|
|
|
This example shows how to control intensity of LEDs using selected SoC's on-board hardware LED PWM Controller module.
|
|
|
|
## How to use example
|
|
|
|
### Hardware Required
|
|
|
|
* A development board with any Espressif SoC (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.)
|
|
* A USB cable for power supply and programming
|
|
|
|
Connect four LEDs to the following LEDC channels / individual GPIOs:
|
|
|
|
| | Channel 0 | Channel 1 | Channel 2 | Channel 3 |
|
|
| --------------- | --------- | --------- | --------- | --------- |
|
|
| ESP32 | GPIO18 | GPIO19 | GPIO4 | GPIO5 |
|
|
| All other chips | GPIO8 | GPIO9 | GPIO4 | GPIO5 |
|
|
|
|
### Configure the project
|
|
|
|
```
|
|
idf.py menuconfig
|
|
```
|
|
|
|
### Build and Flash
|
|
|
|
Build the project and flash it to the board, then run the monitor tool to view the serial output:
|
|
|
|
Run `idf.py -p PORT flash monitor` to build, flash and monitor the project.
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
See the [Getting Started Guide](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/index.html) for full steps to configure and use ESP-IDF to build projects.
|
|
|
|
## Example Output
|
|
|
|
Running this example, you will see the four LEDs' brightness change repeatedly in the following orders
|
|
|
|
* 1: Fade up / increase intensity on the LEDs connecting to Channel 0/1; Fade down / decrease intensity on the LEDs connecting to Channel 2/3
|
|
* 2: Fade down / decrease intensity on the LEDs connecting to Channel 0/1;Fade up / increase intensity on the LEDs connecting to Channel 2/3
|
|
* 3: All LEDs keep a stable intensity
|
|
* 4: All LEDs are off
|
|
|
|
you can also see the following output log on the serial monitor:
|
|
|
|
```
|
|
1. LEDC fade up to duty = 4000
|
|
2. LEDC fade down to duty = 0
|
|
3. LEDC set duty = 4000 without fade
|
|
4. LEDC set duty = 0 without fade
|
|
...
|
|
```
|
|
|
|
## Troubleshooting
|
|
|
|
* Programming fail
|
|
|
|
* Hardware connection is not correct: run `idf.py -p PORT monitor`, and reboot your board to see if there are any output logs.
|
|
* The baud rate for downloading is too high: lower your baud rate in the `menuconfig` menu, and try again.
|
|
|
|
For any technical queries, please open an [issue](https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you soon.
|