mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
336 lines
14 KiB
C
336 lines
14 KiB
C
/*
|
|
* SPDX-FileCopyrightText: 2022 Espressif Systems (Shanghai) CO LTD
|
|
*
|
|
* SPDX-License-Identifier: Unlicense OR CC0-1.0
|
|
*/
|
|
|
|
#include <stdio.h>
|
|
#include <string.h>
|
|
#include "freertos/FreeRTOS.h"
|
|
#include "freertos/task.h"
|
|
#include "esp_netif.h"
|
|
#include "esp_netif_br_glue.h"
|
|
#include "esp_eth.h"
|
|
#include "esp_event.h"
|
|
#include "esp_log.h"
|
|
#include "driver/gpio.h"
|
|
#include "sdkconfig.h"
|
|
#if CONFIG_ETH_USE_SPI_ETHERNET
|
|
#include "driver/spi_master.h"
|
|
#endif // CONFIG_ETH_USE_SPI_ETHERNET
|
|
|
|
static const char *TAG = "eth_bridge_example";
|
|
|
|
#if CONFIG_EXAMPLE_SPI_ETHERNETS_NUM
|
|
#define SPI_ETHERNETS_NUM CONFIG_EXAMPLE_SPI_ETHERNETS_NUM
|
|
#else
|
|
#define SPI_ETHERNETS_NUM 0
|
|
#endif
|
|
|
|
#if CONFIG_EXAMPLE_USE_INTERNAL_ETHERNET
|
|
#define INTERNAL_ETHERNETS_NUM 1
|
|
#else
|
|
#define INTERNAL_ETHERNETS_NUM 0
|
|
#endif
|
|
|
|
#if CONFIG_EXAMPLE_USE_SPI_ETHERNET
|
|
#define INIT_SPI_ETH_MODULE_CONFIG(eth_module_config, num) \
|
|
do { \
|
|
eth_module_config[num].spi_cs_gpio = CONFIG_EXAMPLE_ETH_SPI_CS ##num## _GPIO; \
|
|
eth_module_config[num].int_gpio = CONFIG_EXAMPLE_ETH_SPI_INT ##num## _GPIO; \
|
|
eth_module_config[num].phy_reset_gpio = CONFIG_EXAMPLE_ETH_SPI_PHY_RST ##num## _GPIO; \
|
|
eth_module_config[num].phy_addr = CONFIG_EXAMPLE_ETH_SPI_PHY_ADDR ##num; \
|
|
} while(0)
|
|
|
|
typedef struct {
|
|
uint8_t spi_cs_gpio;
|
|
uint8_t int_gpio;
|
|
int8_t phy_reset_gpio;
|
|
uint8_t phy_addr;
|
|
}spi_eth_module_config_t;
|
|
#endif
|
|
|
|
/** Event handler for Ethernet events */
|
|
static void eth_event_handler(void *arg, esp_event_base_t event_base,
|
|
int32_t event_id, void *event_data)
|
|
{
|
|
uint8_t mac_addr[6] = {0};
|
|
/* we can get the ethernet driver handle from event data */
|
|
esp_eth_handle_t eth_handle = *(esp_eth_handle_t *)event_data;
|
|
|
|
switch (event_id) {
|
|
case ETHERNET_EVENT_CONNECTED:
|
|
esp_eth_ioctl(eth_handle, ETH_CMD_G_MAC_ADDR, mac_addr);
|
|
ESP_LOGI(TAG, "Ethernet (%p) Link Up", eth_handle);
|
|
ESP_LOGI(TAG, "Ethernet HW Addr %02x:%02x:%02x:%02x:%02x:%02x",
|
|
mac_addr[0], mac_addr[1], mac_addr[2], mac_addr[3], mac_addr[4], mac_addr[5]);
|
|
break;
|
|
case ETHERNET_EVENT_DISCONNECTED:
|
|
ESP_LOGI(TAG, "Ethernet (%p) Link Down", eth_handle);
|
|
break;
|
|
case ETHERNET_EVENT_START:
|
|
ESP_LOGI(TAG, "Ethernet (%p) Started", eth_handle);
|
|
break;
|
|
case ETHERNET_EVENT_STOP:
|
|
ESP_LOGI(TAG, "Ethernet (%p) Stopped", eth_handle);
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
/** Event handler for IP_EVENT_ETH_GOT_IP */
|
|
static void got_ip_event_handler(void *arg, esp_event_base_t event_base,
|
|
int32_t event_id, void *event_data)
|
|
{
|
|
ip_event_got_ip_t *event = (ip_event_got_ip_t *) event_data;
|
|
const esp_netif_ip_info_t *ip_info = &event->ip_info;
|
|
|
|
ESP_LOGI(TAG, "Ethernet Got IP Address");
|
|
ESP_LOGI(TAG, "~~~~~~~~~~~");
|
|
ESP_LOGI(TAG, "ETHIP:" IPSTR, IP2STR(&ip_info->ip));
|
|
ESP_LOGI(TAG, "ETHMASK:" IPSTR, IP2STR(&ip_info->netmask));
|
|
ESP_LOGI(TAG, "ETHGW:" IPSTR, IP2STR(&ip_info->gw));
|
|
ESP_LOGI(TAG, "~~~~~~~~~~~");
|
|
}
|
|
|
|
#if CONFIG_EXAMPLE_USE_INTERNAL_ETHERNET
|
|
/** Internal EMAC initialization */
|
|
esp_eth_handle_t eth_init_internal(void)
|
|
{
|
|
esp_eth_handle_t eth_handle;
|
|
|
|
// Init MAC and PHY configs to default
|
|
eth_mac_config_t mac_config = ETH_MAC_DEFAULT_CONFIG();
|
|
eth_phy_config_t phy_config = ETH_PHY_DEFAULT_CONFIG();
|
|
|
|
phy_config.phy_addr = CONFIG_EXAMPLE_ETH_PHY_ADDR;
|
|
phy_config.reset_gpio_num = CONFIG_EXAMPLE_ETH_PHY_RST_GPIO;
|
|
eth_esp32_emac_config_t esp32_emac_config = ETH_ESP32_EMAC_DEFAULT_CONFIG();
|
|
esp32_emac_config.smi_mdc_gpio_num = CONFIG_EXAMPLE_ETH_MDC_GPIO;
|
|
esp32_emac_config.smi_mdio_gpio_num = CONFIG_EXAMPLE_ETH_MDIO_GPIO;
|
|
esp_eth_mac_t *mac = esp_eth_mac_new_esp32(&esp32_emac_config, &mac_config);
|
|
#if CONFIG_EXAMPLE_ETH_PHY_IP101
|
|
esp_eth_phy_t *phy = esp_eth_phy_new_ip101(&phy_config);
|
|
#elif CONFIG_EXAMPLE_ETH_PHY_RTL8201
|
|
esp_eth_phy_t *phy = esp_eth_phy_new_rtl8201(&phy_config);
|
|
#elif CONFIG_EXAMPLE_ETH_PHY_LAN87XX
|
|
esp_eth_phy_t *phy = esp_eth_phy_new_lan87xx(&phy_config);
|
|
#elif CONFIG_EXAMPLE_ETH_PHY_DP83848
|
|
esp_eth_phy_t *phy = esp_eth_phy_new_dp83848(&phy_config);
|
|
#elif CONFIG_EXAMPLE_ETH_PHY_KSZ80XX
|
|
esp_eth_phy_t *phy = esp_eth_phy_new_ksz80xx(&phy_config);
|
|
#endif
|
|
esp_eth_config_t config = ETH_DEFAULT_CONFIG(mac, phy);
|
|
ESP_ERROR_CHECK(esp_eth_driver_install(&config, ð_handle));
|
|
|
|
return eth_handle;
|
|
}
|
|
#endif // CONFIG_EXAMPLE_USE_INTERNAL_ETHERNET
|
|
|
|
#if CONFIG_EXAMPLE_USE_SPI_ETHERNET
|
|
/** Ethernet SPI modules initialization */
|
|
esp_eth_handle_t eth_init_spi(spi_eth_module_config_t *spi_eth_module_config, uint8_t *mac_addr)
|
|
{
|
|
esp_eth_handle_t eth_handle;
|
|
|
|
// Init MAC and PHY configs to default
|
|
eth_mac_config_t mac_config = ETH_MAC_DEFAULT_CONFIG();
|
|
eth_phy_config_t phy_config = ETH_PHY_DEFAULT_CONFIG();
|
|
|
|
// Configure SPI interface and Ethernet driver for specific SPI module
|
|
esp_eth_mac_t *mac;
|
|
esp_eth_phy_t *phy;
|
|
|
|
spi_device_handle_t spi_handle;
|
|
#if CONFIG_EXAMPLE_USE_KSZ8851SNL
|
|
spi_device_interface_config_t devcfg = {
|
|
.mode = 0,
|
|
.clock_speed_hz = CONFIG_EXAMPLE_ETH_SPI_CLOCK_MHZ * 1000 * 1000,
|
|
.queue_size = 20
|
|
};
|
|
|
|
// Set SPI module Chip Select GPIO
|
|
devcfg.spics_io_num = spi_eth_module_config->spi_cs_gpio;
|
|
|
|
ESP_ERROR_CHECK(spi_bus_add_device(CONFIG_EXAMPLE_ETH_SPI_HOST, &devcfg, &spi_handle));
|
|
// KSZ8851SNL ethernet driver is based on spi driver
|
|
eth_ksz8851snl_config_t ksz8851snl_config = ETH_KSZ8851SNL_DEFAULT_CONFIG(spi_handle);
|
|
|
|
// Set remaining GPIO numbers and configuration used by the SPI module
|
|
ksz8851snl_config.int_gpio_num = spi_eth_module_config->int_gpio;
|
|
phy_config.phy_addr = spi_eth_module_config->phy_addr;
|
|
phy_config.reset_gpio_num = spi_eth_module_config->phy_reset_gpio;
|
|
|
|
mac = esp_eth_mac_new_ksz8851snl(&ksz8851snl_config, &mac_config);
|
|
phy = esp_eth_phy_new_ksz8851snl(&phy_config);
|
|
#elif CONFIG_EXAMPLE_USE_DM9051
|
|
spi_device_interface_config_t devcfg = {
|
|
.command_bits = 1,
|
|
.address_bits = 7,
|
|
.mode = 0,
|
|
.clock_speed_hz = CONFIG_EXAMPLE_ETH_SPI_CLOCK_MHZ * 1000 * 1000,
|
|
.queue_size = 20
|
|
};
|
|
|
|
// Set SPI module Chip Select GPIO
|
|
devcfg.spics_io_num = spi_eth_module_config->spi_cs_gpio;
|
|
|
|
ESP_ERROR_CHECK(spi_bus_add_device(CONFIG_EXAMPLE_ETH_SPI_HOST, &devcfg, &spi_handle));
|
|
// dm9051 ethernet driver is based on spi driver
|
|
eth_dm9051_config_t dm9051_config = ETH_DM9051_DEFAULT_CONFIG(spi_handle);
|
|
|
|
// Set remaining GPIO numbers and configuration used by the SPI module
|
|
dm9051_config.int_gpio_num = spi_eth_module_config->int_gpio;
|
|
phy_config.phy_addr = spi_eth_module_config->phy_addr;
|
|
phy_config.reset_gpio_num = spi_eth_module_config->phy_reset_gpio;
|
|
|
|
mac = esp_eth_mac_new_dm9051(&dm9051_config, &mac_config);
|
|
phy = esp_eth_phy_new_dm9051(&phy_config);
|
|
#elif CONFIG_EXAMPLE_USE_W5500
|
|
spi_device_interface_config_t devcfg = {
|
|
.command_bits = 16, // Actually it's the address phase in W5500 SPI frame
|
|
.address_bits = 8, // Actually it's the control phase in W5500 SPI frame
|
|
.mode = 0,
|
|
.clock_speed_hz = CONFIG_EXAMPLE_ETH_SPI_CLOCK_MHZ * 1000 * 1000,
|
|
.queue_size = 20
|
|
};
|
|
|
|
// Set SPI module Chip Select GPIO
|
|
devcfg.spics_io_num = spi_eth_module_config->spi_cs_gpio;
|
|
|
|
ESP_ERROR_CHECK(spi_bus_add_device(CONFIG_EXAMPLE_ETH_SPI_HOST, &devcfg, &spi_handle));
|
|
// w5500 ethernet driver is based on spi driver
|
|
eth_w5500_config_t w5500_config = ETH_W5500_DEFAULT_CONFIG(spi_handle);
|
|
|
|
// Set remaining GPIO numbers and configuration used by the SPI module
|
|
w5500_config.int_gpio_num = spi_eth_module_config->int_gpio;
|
|
phy_config.phy_addr = spi_eth_module_config->phy_addr;
|
|
phy_config.reset_gpio_num = spi_eth_module_config->phy_reset_gpio;
|
|
|
|
mac = esp_eth_mac_new_w5500(&w5500_config, &mac_config);
|
|
phy = esp_eth_phy_new_w5500(&phy_config);
|
|
|
|
#endif //CONFIG_EXAMPLE_USE_W5500
|
|
esp_eth_config_t eth_config_spi = ETH_DEFAULT_CONFIG(mac, phy);
|
|
ESP_ERROR_CHECK(esp_eth_driver_install(ð_config_spi, ð_handle));
|
|
|
|
// The SPI Ethernet module might not have a burned factory MAC address, we cat to set it manually.
|
|
ESP_ERROR_CHECK(esp_eth_ioctl(eth_handle, ETH_CMD_S_MAC_ADDR, mac_addr));
|
|
|
|
return eth_handle;
|
|
}
|
|
#endif // CONFIG_EXAMPLE_USE_SPI_ETHERNET
|
|
|
|
void app_main(void)
|
|
{
|
|
// number of Ethernet ports to be used in the bridge
|
|
uint8_t port_cnt = 0;
|
|
// the same MAC address will be used for all Ethernet ports since the bridge acts as one device
|
|
uint8_t common_mac_addr[ETH_ADDR_LEN];
|
|
|
|
esp_eth_handle_t eth_handles[SPI_ETHERNETS_NUM + INTERNAL_ETHERNETS_NUM] = { NULL };
|
|
esp_netif_t *eth_netifs[SPI_ETHERNETS_NUM + INTERNAL_ETHERNETS_NUM] = { NULL };
|
|
|
|
// Initialize TCP/IP network interface (should be called only once in application)
|
|
ESP_ERROR_CHECK(esp_netif_init());
|
|
// Create default event loop that running in background
|
|
ESP_ERROR_CHECK(esp_event_loop_create_default());
|
|
|
|
#if CONFIG_EXAMPLE_USE_INTERNAL_ETHERNET
|
|
eth_handles[port_cnt++] = eth_init_internal();
|
|
// use burned ESP32 MAC address as commom address for all Ethernet interfaces
|
|
ESP_ERROR_CHECK(esp_eth_ioctl(eth_handles[0], ETH_CMD_G_MAC_ADDR, common_mac_addr));
|
|
#elif CONFIG_EXAMPLE_USE_SPI_ETHERNET
|
|
// if ESP32 internal Ethernet is not used, use manually configured MAC address
|
|
// 02:00:00 is a Locally Administered OUI range so should not be used except when testing on a LAN under your control.
|
|
memcpy(common_mac_addr, (uint8_t[]) {0x02, 0x00, 0x00, 0x12, 0x34, 0x56}, ETH_ADDR_LEN);
|
|
#endif //CONFIG_EXAMPLE_USE_INTERNAL_ETHERNET
|
|
|
|
#if CONFIG_EXAMPLE_USE_SPI_ETHERNET
|
|
// Install GPIO ISR handler to be able to service SPI Eth modlues interrupts
|
|
gpio_install_isr_service(0);
|
|
|
|
// Init SPI bus
|
|
spi_bus_config_t buscfg = {
|
|
.miso_io_num = CONFIG_EXAMPLE_ETH_SPI_MISO_GPIO,
|
|
.mosi_io_num = CONFIG_EXAMPLE_ETH_SPI_MOSI_GPIO,
|
|
.sclk_io_num = CONFIG_EXAMPLE_ETH_SPI_SCLK_GPIO,
|
|
.quadwp_io_num = -1,
|
|
.quadhd_io_num = -1,
|
|
};
|
|
ESP_ERROR_CHECK(spi_bus_initialize(CONFIG_EXAMPLE_ETH_SPI_HOST, &buscfg, SPI_DMA_CH_AUTO));
|
|
|
|
// Init specific SPI Ethernet module configuration from Kconfig (CS GPIO, Interrupt GPIO, etc.)
|
|
spi_eth_module_config_t spi_eth_module_config[CONFIG_EXAMPLE_SPI_ETHERNETS_NUM];
|
|
INIT_SPI_ETH_MODULE_CONFIG(spi_eth_module_config, 0);
|
|
#if CONFIG_EXAMPLE_SPI_ETHERNETS_NUM > 1
|
|
INIT_SPI_ETH_MODULE_CONFIG(spi_eth_module_config, 1);
|
|
#endif
|
|
for (int i = 0; i < CONFIG_EXAMPLE_SPI_ETHERNETS_NUM; i++) {
|
|
eth_handles[port_cnt++] = eth_init_spi(&spi_eth_module_config[i], common_mac_addr);
|
|
}
|
|
#endif // CONFIG_ETH_USE_SPI_ETHERNET
|
|
// Create instances of esp-netif for Ethernet ports
|
|
esp_netif_inherent_config_t esp_netif_config = ESP_NETIF_INHERENT_DEFAULT_ETH();
|
|
esp_netif_config_t netif_cfg = {
|
|
.base = &esp_netif_config,
|
|
.stack = ESP_NETIF_NETSTACK_DEFAULT_ETH
|
|
};
|
|
char if_key_str[10];
|
|
char if_desc_str[10];
|
|
char num_str[3];
|
|
for (int i = 0; i < port_cnt; i++) {
|
|
itoa(i, num_str, 10);
|
|
strcat(strcpy(if_key_str, "ETH_"), num_str);
|
|
strcat(strcpy(if_desc_str, "eth"), num_str);
|
|
esp_netif_config.if_key = if_key_str;
|
|
esp_netif_config.if_desc = if_desc_str;
|
|
esp_netif_config.route_prio = 50 - i;
|
|
esp_netif_config.flags = 0; // ESP-NETIF flags need to be zero when port's to be bridged
|
|
|
|
eth_netifs[i] = esp_netif_new(&netif_cfg);
|
|
|
|
// attach Ethernet driver to TCP/IP stack
|
|
ESP_ERROR_CHECK(esp_netif_attach(eth_netifs[i], esp_eth_new_netif_glue(eth_handles[i])));
|
|
}
|
|
|
|
// Create instance of esp-netif for bridge interface
|
|
esp_netif_inherent_config_t esp_netif_br_config = ESP_NETIF_INHERENT_DEFAULT_BR();
|
|
esp_netif_config_t netif_br_cfg = {
|
|
.base = &esp_netif_br_config,
|
|
.stack = ESP_NETIF_NETSTACK_DEFAULT_BR,
|
|
};
|
|
// Bridge configuration
|
|
bridgeif_config_t bridgeif_config = {
|
|
.max_fdb_dyn_entries = 10, // maximum number of address entries in dynamic forwarding database
|
|
.max_fdb_sta_entries = 2, // maximum number of address entries in static forwarding database
|
|
.max_ports = port_cnt // maximum number of ports the bridge can consist of
|
|
};
|
|
esp_netif_br_config.bridge_info = &bridgeif_config;
|
|
// Set MAC address of bridge interface the same as the Ethernet interface
|
|
memcpy(esp_netif_br_config.mac, common_mac_addr, ETH_ADDR_LEN);
|
|
esp_netif_t *br_netif = esp_netif_new(&netif_br_cfg);
|
|
|
|
// Create new esp netif bridge glue instance
|
|
esp_netif_br_glue_handle_t netif_br_glue = esp_netif_br_glue_new();
|
|
// Add Ethernet port interfaces to that esp netif bridge glue instance
|
|
for (int i = 0; i < port_cnt; i++) {
|
|
ESP_ERROR_CHECK(esp_netif_br_glue_add_port(netif_br_glue, eth_netifs[i]));
|
|
}
|
|
// Attach esp netif bridge glue instance with added ports to bridge netif
|
|
ESP_ERROR_CHECK(esp_netif_attach(br_netif, netif_br_glue));
|
|
|
|
// Register user defined event handers
|
|
ESP_ERROR_CHECK(esp_event_handler_register(ETH_EVENT, ESP_EVENT_ANY_ID, ð_event_handler, NULL));
|
|
ESP_ERROR_CHECK(esp_event_handler_register(IP_EVENT, IP_EVENT_ETH_GOT_IP, &got_ip_event_handler, NULL));
|
|
|
|
for (int i = 0; i < port_cnt; i++) {
|
|
// Since the MAC forwarding is performed in lwIP bridge, we need to pass all addresses through the Ethernet MACs
|
|
bool promiscuous = true;
|
|
esp_eth_ioctl(eth_handles[i], ETH_CMD_S_PROMISCUOUS, &promiscuous);
|
|
// Start Ethernet driver state machine
|
|
ESP_ERROR_CHECK(esp_eth_start(eth_handles[i]));
|
|
}
|
|
}
|