mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
66fb5a29bb
Apply the pre-commit hook whitespace fixes to all files in the repo. (Line endings, blank lines at end of file, trailing whitespace)
349 lines
16 KiB
C
349 lines
16 KiB
C
// Copyright 2015-2018 Espressif Systems (Shanghai) PTE LTD
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
#pragma once
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
#include "soc/soc_caps.h"
|
|
#if SOC_TWAI_SUPPORTED
|
|
|
|
#include "freertos/FreeRTOS.h"
|
|
#include "esp_types.h"
|
|
#include "esp_intr_alloc.h"
|
|
#include "esp_err.h"
|
|
#include "gpio.h"
|
|
#include "hal/twai_types.h"
|
|
|
|
/* -------------------- Default initializers and flags ---------------------- */
|
|
/** @cond */ //Doxy command to hide preprocessor definitions from docs
|
|
/**
|
|
* @brief Initializer macro for general configuration structure.
|
|
*
|
|
* This initializer macros allows the TX GPIO, RX GPIO, and operating mode to be
|
|
* configured. The other members of the general configuration structure are
|
|
* assigned default values.
|
|
*/
|
|
#define TWAI_GENERAL_CONFIG_DEFAULT(tx_io_num, rx_io_num, op_mode) {.mode = op_mode, .tx_io = tx_io_num, .rx_io = rx_io_num, \
|
|
.clkout_io = TWAI_IO_UNUSED, .bus_off_io = TWAI_IO_UNUSED, \
|
|
.tx_queue_len = 5, .rx_queue_len = 5, \
|
|
.alerts_enabled = TWAI_ALERT_NONE, .clkout_divider = 0, \
|
|
.intr_flags = ESP_INTR_FLAG_LEVEL1}
|
|
|
|
/**
|
|
* @brief Alert flags
|
|
*
|
|
* The following flags represents the various kind of alerts available in
|
|
* the TWAI driver. These flags can be used when configuring/reconfiguring
|
|
* alerts, or when calling twai_read_alerts().
|
|
*
|
|
* @note The TWAI_ALERT_AND_LOG flag is not an actual alert, but will configure
|
|
* the TWAI driver to log to UART when an enabled alert occurs.
|
|
*/
|
|
#define TWAI_ALERT_TX_IDLE 0x0001 /**< Alert(1): No more messages to transmit */
|
|
#define TWAI_ALERT_TX_SUCCESS 0x0002 /**< Alert(2): The previous transmission was successful */
|
|
#define TWAI_ALERT_BELOW_ERR_WARN 0x0004 /**< Alert(4): Both error counters have dropped below error warning limit */
|
|
#define TWAI_ALERT_ERR_ACTIVE 0x0008 /**< Alert(8): TWAI controller has become error active */
|
|
#define TWAI_ALERT_RECOVERY_IN_PROGRESS 0x0010 /**< Alert(16): TWAI controller is undergoing bus recovery */
|
|
#define TWAI_ALERT_BUS_RECOVERED 0x0020 /**< Alert(32): TWAI controller has successfully completed bus recovery */
|
|
#define TWAI_ALERT_ARB_LOST 0x0040 /**< Alert(64): The previous transmission lost arbitration */
|
|
#define TWAI_ALERT_ABOVE_ERR_WARN 0x0080 /**< Alert(128): One of the error counters have exceeded the error warning limit */
|
|
#define TWAI_ALERT_BUS_ERROR 0x0100 /**< Alert(256): A (Bit, Stuff, CRC, Form, ACK) error has occurred on the bus */
|
|
#define TWAI_ALERT_TX_FAILED 0x0200 /**< Alert(512): The previous transmission has failed (for single shot transmission) */
|
|
#define TWAI_ALERT_RX_QUEUE_FULL 0x0400 /**< Alert(1024): The RX queue is full causing a frame to be lost */
|
|
#define TWAI_ALERT_ERR_PASS 0x0800 /**< Alert(2048): TWAI controller has become error passive */
|
|
#define TWAI_ALERT_BUS_OFF 0x1000 /**< Alert(4096): Bus-off condition occurred. TWAI controller can no longer influence bus */
|
|
#define TWAI_ALERT_ALL 0x1FFF /**< Bit mask to enable all alerts during configuration */
|
|
#define TWAI_ALERT_NONE 0x0000 /**< Bit mask to disable all alerts during configuration */
|
|
#define TWAI_ALERT_AND_LOG 0x2000 /**< Bit mask to enable alerts to also be logged when they occur. Note that logging from the ISR is disabled if CONFIG_TWAI_ISR_IN_IRAM is enabled (see docs). */
|
|
|
|
/** @endcond */
|
|
|
|
#define TWAI_IO_UNUSED ((gpio_num_t) -1) /**< Marks GPIO as unused in TWAI configuration */
|
|
|
|
/* ----------------------- Enum and Struct Definitions ---------------------- */
|
|
|
|
/**
|
|
* @brief TWAI driver states
|
|
*/
|
|
typedef enum {
|
|
TWAI_STATE_STOPPED, /**< Stopped state. The TWAI controller will not participate in any TWAI bus activities */
|
|
TWAI_STATE_RUNNING, /**< Running state. The TWAI controller can transmit and receive messages */
|
|
TWAI_STATE_BUS_OFF, /**< Bus-off state. The TWAI controller cannot participate in bus activities until it has recovered */
|
|
TWAI_STATE_RECOVERING, /**< Recovering state. The TWAI controller is undergoing bus recovery */
|
|
} twai_state_t;
|
|
|
|
/**
|
|
* @brief Structure for general configuration of the TWAI driver
|
|
*
|
|
* @note Macro initializers are available for this structure
|
|
*/
|
|
typedef struct {
|
|
twai_mode_t mode; /**< Mode of TWAI controller */
|
|
gpio_num_t tx_io; /**< Transmit GPIO number */
|
|
gpio_num_t rx_io; /**< Receive GPIO number */
|
|
gpio_num_t clkout_io; /**< CLKOUT GPIO number (optional, set to -1 if unused) */
|
|
gpio_num_t bus_off_io; /**< Bus off indicator GPIO number (optional, set to -1 if unused) */
|
|
uint32_t tx_queue_len; /**< Number of messages TX queue can hold (set to 0 to disable TX Queue) */
|
|
uint32_t rx_queue_len; /**< Number of messages RX queue can hold */
|
|
uint32_t alerts_enabled; /**< Bit field of alerts to enable (see documentation) */
|
|
uint32_t clkout_divider; /**< CLKOUT divider. Can be 1 or any even number from 2 to 14 (optional, set to 0 if unused) */
|
|
int intr_flags; /**< Interrupt flags to set the priority of the driver's ISR. Note that to use the ESP_INTR_FLAG_IRAM, the CONFIG_TWAI_ISR_IN_IRAM option should be enabled first. */
|
|
} twai_general_config_t;
|
|
|
|
/**
|
|
* @brief Structure to store status information of TWAI driver
|
|
*/
|
|
typedef struct {
|
|
twai_state_t state; /**< Current state of TWAI controller (Stopped/Running/Bus-Off/Recovery) */
|
|
uint32_t msgs_to_tx; /**< Number of messages queued for transmission or awaiting transmission completion */
|
|
uint32_t msgs_to_rx; /**< Number of messages in RX queue waiting to be read */
|
|
uint32_t tx_error_counter; /**< Current value of Transmit Error Counter */
|
|
uint32_t rx_error_counter; /**< Current value of Receive Error Counter */
|
|
uint32_t tx_failed_count; /**< Number of messages that failed transmissions */
|
|
uint32_t rx_missed_count; /**< Number of messages that were lost due to a full RX queue */
|
|
uint32_t arb_lost_count; /**< Number of instances arbitration was lost */
|
|
uint32_t bus_error_count; /**< Number of instances a bus error has occurred */
|
|
} twai_status_info_t;
|
|
|
|
/* ------------------------------ Public API -------------------------------- */
|
|
|
|
/**
|
|
* @brief Install TWAI driver
|
|
*
|
|
* This function installs the TWAI driver using three configuration structures.
|
|
* The required memory is allocated and the TWAI driver is placed in the stopped
|
|
* state after running this function.
|
|
*
|
|
* @param[in] g_config General configuration structure
|
|
* @param[in] t_config Timing configuration structure
|
|
* @param[in] f_config Filter configuration structure
|
|
*
|
|
* @note Macro initializers are available for the configuration structures (see documentation)
|
|
*
|
|
* @note To reinstall the TWAI driver, call twai_driver_uninstall() first
|
|
*
|
|
* @return
|
|
* - ESP_OK: Successfully installed TWAI driver
|
|
* - ESP_ERR_INVALID_ARG: Arguments are invalid
|
|
* - ESP_ERR_NO_MEM: Insufficient memory
|
|
* - ESP_ERR_INVALID_STATE: Driver is already installed
|
|
*/
|
|
esp_err_t twai_driver_install(const twai_general_config_t *g_config, const twai_timing_config_t *t_config, const twai_filter_config_t *f_config);
|
|
|
|
/**
|
|
* @brief Uninstall the TWAI driver
|
|
*
|
|
* This function uninstalls the TWAI driver, freeing the memory utilized by the
|
|
* driver. This function can only be called when the driver is in the stopped
|
|
* state or the bus-off state.
|
|
*
|
|
* @warning The application must ensure that no tasks are blocked on TX/RX
|
|
* queues or alerts when this function is called.
|
|
*
|
|
* @return
|
|
* - ESP_OK: Successfully uninstalled TWAI driver
|
|
* - ESP_ERR_INVALID_STATE: Driver is not in stopped/bus-off state, or is not installed
|
|
*/
|
|
esp_err_t twai_driver_uninstall(void);
|
|
|
|
/**
|
|
* @brief Start the TWAI driver
|
|
*
|
|
* This function starts the TWAI driver, putting the TWAI driver into the running
|
|
* state. This allows the TWAI driver to participate in TWAI bus activities such
|
|
* as transmitting/receiving messages. The TX and RX queue are reset in this function,
|
|
* clearing any messages that are unread or pending transmission. This function
|
|
* can only be called when the TWAI driver is in the stopped state.
|
|
*
|
|
* @return
|
|
* - ESP_OK: TWAI driver is now running
|
|
* - ESP_ERR_INVALID_STATE: Driver is not in stopped state, or is not installed
|
|
*/
|
|
esp_err_t twai_start(void);
|
|
|
|
/**
|
|
* @brief Stop the TWAI driver
|
|
*
|
|
* This function stops the TWAI driver, preventing any further message from being
|
|
* transmitted or received until twai_start() is called. Any messages in the TX
|
|
* queue are cleared. Any messages in the RX queue should be read by the
|
|
* application after this function is called. This function can only be called
|
|
* when the TWAI driver is in the running state.
|
|
*
|
|
* @warning A message currently being transmitted/received on the TWAI bus will
|
|
* be ceased immediately. This may lead to other TWAI nodes interpreting
|
|
* the unfinished message as an error.
|
|
*
|
|
* @return
|
|
* - ESP_OK: TWAI driver is now Stopped
|
|
* - ESP_ERR_INVALID_STATE: Driver is not in running state, or is not installed
|
|
*/
|
|
esp_err_t twai_stop(void);
|
|
|
|
/**
|
|
* @brief Transmit a TWAI message
|
|
*
|
|
* This function queues a TWAI message for transmission. Transmission will start
|
|
* immediately if no other messages are queued for transmission. If the TX queue
|
|
* is full, this function will block until more space becomes available or until
|
|
* it times out. If the TX queue is disabled (TX queue length = 0 in configuration),
|
|
* this function will return immediately if another message is undergoing
|
|
* transmission. This function can only be called when the TWAI driver is in the
|
|
* running state and cannot be called under Listen Only Mode.
|
|
*
|
|
* @param[in] message Message to transmit
|
|
* @param[in] ticks_to_wait Number of FreeRTOS ticks to block on the TX queue
|
|
*
|
|
* @note This function does not guarantee that the transmission is successful.
|
|
* The TX_SUCCESS/TX_FAILED alert can be enabled to alert the application
|
|
* upon the success/failure of a transmission.
|
|
*
|
|
* @note The TX_IDLE alert can be used to alert the application when no other
|
|
* messages are awaiting transmission.
|
|
*
|
|
* @return
|
|
* - ESP_OK: Transmission successfully queued/initiated
|
|
* - ESP_ERR_INVALID_ARG: Arguments are invalid
|
|
* - ESP_ERR_TIMEOUT: Timed out waiting for space on TX queue
|
|
* - ESP_FAIL: TX queue is disabled and another message is currently transmitting
|
|
* - ESP_ERR_INVALID_STATE: TWAI driver is not in running state, or is not installed
|
|
* - ESP_ERR_NOT_SUPPORTED: Listen Only Mode does not support transmissions
|
|
*/
|
|
esp_err_t twai_transmit(const twai_message_t *message, TickType_t ticks_to_wait);
|
|
|
|
/**
|
|
* @brief Receive a TWAI message
|
|
*
|
|
* This function receives a message from the RX queue. The flags field of the
|
|
* message structure will indicate the type of message received. This function
|
|
* will block if there are no messages in the RX queue
|
|
*
|
|
* @param[out] message Received message
|
|
* @param[in] ticks_to_wait Number of FreeRTOS ticks to block on RX queue
|
|
*
|
|
* @warning The flags field of the received message should be checked to determine
|
|
* if the received message contains any data bytes.
|
|
*
|
|
* @return
|
|
* - ESP_OK: Message successfully received from RX queue
|
|
* - ESP_ERR_TIMEOUT: Timed out waiting for message
|
|
* - ESP_ERR_INVALID_ARG: Arguments are invalid
|
|
* - ESP_ERR_INVALID_STATE: TWAI driver is not installed
|
|
*/
|
|
esp_err_t twai_receive(twai_message_t *message, TickType_t ticks_to_wait);
|
|
|
|
/**
|
|
* @brief Read TWAI driver alerts
|
|
*
|
|
* This function will read the alerts raised by the TWAI driver. If no alert has
|
|
* been issued when this function is called, this function will block until an alert
|
|
* occurs or until it timeouts.
|
|
*
|
|
* @param[out] alerts Bit field of raised alerts (see documentation for alert flags)
|
|
* @param[in] ticks_to_wait Number of FreeRTOS ticks to block for alert
|
|
*
|
|
* @note Multiple alerts can be raised simultaneously. The application should
|
|
* check for all alerts that have been enabled.
|
|
*
|
|
* @return
|
|
* - ESP_OK: Alerts read
|
|
* - ESP_ERR_TIMEOUT: Timed out waiting for alerts
|
|
* - ESP_ERR_INVALID_ARG: Arguments are invalid
|
|
* - ESP_ERR_INVALID_STATE: TWAI driver is not installed
|
|
*/
|
|
esp_err_t twai_read_alerts(uint32_t *alerts, TickType_t ticks_to_wait);
|
|
|
|
/**
|
|
* @brief Reconfigure which alerts are enabled
|
|
*
|
|
* This function reconfigures which alerts are enabled. If there are alerts
|
|
* which have not been read whilst reconfiguring, this function can read those
|
|
* alerts.
|
|
*
|
|
* @param[in] alerts_enabled Bit field of alerts to enable (see documentation for alert flags)
|
|
* @param[out] current_alerts Bit field of currently raised alerts. Set to NULL if unused
|
|
*
|
|
* @return
|
|
* - ESP_OK: Alerts reconfigured
|
|
* - ESP_ERR_INVALID_STATE: TWAI driver is not installed
|
|
*/
|
|
esp_err_t twai_reconfigure_alerts(uint32_t alerts_enabled, uint32_t *current_alerts);
|
|
|
|
/**
|
|
* @brief Start the bus recovery process
|
|
*
|
|
* This function initiates the bus recovery process when the TWAI driver is in
|
|
* the bus-off state. Once initiated, the TWAI driver will enter the recovering
|
|
* state and wait for 128 occurrences of the bus-free signal on the TWAI bus
|
|
* before returning to the stopped state. This function will reset the TX queue,
|
|
* clearing any messages pending transmission.
|
|
*
|
|
* @note The BUS_RECOVERED alert can be enabled to alert the application when
|
|
* the bus recovery process completes.
|
|
*
|
|
* @return
|
|
* - ESP_OK: Bus recovery started
|
|
* - ESP_ERR_INVALID_STATE: TWAI driver is not in the bus-off state, or is not installed
|
|
*/
|
|
esp_err_t twai_initiate_recovery(void);
|
|
|
|
/**
|
|
* @brief Get current status information of the TWAI driver
|
|
*
|
|
* @param[out] status_info Status information
|
|
*
|
|
* @return
|
|
* - ESP_OK: Status information retrieved
|
|
* - ESP_ERR_INVALID_ARG: Arguments are invalid
|
|
* - ESP_ERR_INVALID_STATE: TWAI driver is not installed
|
|
*/
|
|
esp_err_t twai_get_status_info(twai_status_info_t *status_info);
|
|
|
|
/**
|
|
* @brief Clear the transmit queue
|
|
*
|
|
* This function will clear the transmit queue of all messages.
|
|
*
|
|
* @note The transmit queue is automatically cleared when twai_stop() or
|
|
* twai_initiate_recovery() is called.
|
|
*
|
|
* @return
|
|
* - ESP_OK: Transmit queue cleared
|
|
* - ESP_ERR_INVALID_STATE: TWAI driver is not installed or TX queue is disabled
|
|
*/
|
|
esp_err_t twai_clear_transmit_queue(void);
|
|
|
|
/**
|
|
* @brief Clear the receive queue
|
|
*
|
|
* This function will clear the receive queue of all messages.
|
|
*
|
|
* @note The receive queue is automatically cleared when twai_start() is
|
|
* called.
|
|
*
|
|
* @return
|
|
* - ESP_OK: Transmit queue cleared
|
|
* - ESP_ERR_INVALID_STATE: TWAI driver is not installed
|
|
*/
|
|
esp_err_t twai_clear_receive_queue(void);
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
#endif //SOC_TWAI_SUPPORTED
|