mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
73 lines
2.8 KiB
Markdown
73 lines
2.8 KiB
Markdown
| Supported Targets | ESP32 | ESP32-C2 | ESP32-C3 | ESP32-C6 | ESP32-H2 | ESP32-S3 |
|
|
| ----------------- | ----- | -------- | -------- | -------- | -------- | -------- |
|
|
|
|
# BLE Heart Rate Measurement Example
|
|
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
|
|
|
This example creates GATT server demonstrating standard Heart Rate measurement service. It simulates Heart rate measurement and notifies to client when the notifications are enabled.
|
|
|
|
It uses ESP32's Bluetooth controller and NimBLE stack based BLE host
|
|
|
|
This example aims at understanding notification subscriptions and sending notifications.
|
|
|
|
To test this demo, any BLE scanner app can be used.
|
|
|
|
Note :
|
|
|
|
* To install the dependency packages needed, please refer to the top level [README file](../../../README.md#running-test-python-script-pytest).
|
|
* Currently this Python utility is only supported on Linux (BLE communication is via BLuez + DBus).
|
|
|
|
## How to Use Example
|
|
|
|
Before project configuration and build, be sure to set the correct chip target using:
|
|
|
|
```bash
|
|
idf.py set-target <chip_name>
|
|
```
|
|
|
|
### Hardware Required
|
|
|
|
* A development board with ESP32/ESP32-C3 SoC (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.)
|
|
* A USB cable for Power supply and programming
|
|
|
|
See [Development Boards](https://www.espressif.com/en/products/devkits) for more information about it.
|
|
|
|
### Build and Flash
|
|
|
|
Run `idf.py -p PORT flash monitor` to build, flash and monitor the project.
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
See the [Getting Started Guide](https://idf.espressif.com/) for full steps to configure and use ESP-IDF to build projects.
|
|
|
|
## Example Output
|
|
|
|
This console output can be observed when blehr is connected to client and client enables notifications:
|
|
|
|
```
|
|
I (91) BTDM_INIT: BT controller compile version [fe7ced0]
|
|
I (91) system_api: Base MAC address is not set, read default base MAC address from BLK0 of EFUSE
|
|
I (181) phy: phy_version: 4100, 6fa5e27, Jan 25 2019, 17:02:06, 0, 0
|
|
I (421) NimBLE_BLE_HeartRate: BLE Host Task Started
|
|
GAP procedure initiated: stop advertising.
|
|
Device Address: xx:xx:xx:xx:xx:xx
|
|
GAP procedure initiated: advertise; disc_mode=2 adv_channel_map=0 own_addr_type=0 adv_filter_policy=0 adv_itvl_min=0 adv_itvl_max=0
|
|
connection established; status=0
|
|
subscribe event; cur_notify=1
|
|
value handle; val_handle=3
|
|
I (21611) BLE_GAP_SUBSCRIBE_EVENT: conn_handle from subscribe=0
|
|
GATT procedure initiated: notify; att_handle=3
|
|
GATT procedure initiated: notify; att_handle=3
|
|
GATT procedure initiated: notify; att_handle=3
|
|
GATT procedure initiated: notify; att_handle=3
|
|
GATT procedure initiated: notify; att_handle=3
|
|
GATT procedure initiated: notify; att_handle=3
|
|
GATT procedure initiated: notify; att_handle=3
|
|
|
|
```
|
|
|
|
## Troubleshooting
|
|
|
|
For any technical queries, please open an [issue](https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you soon.
|