esp-idf/components/esp32/test/test_ahb_arb.c
Tian Hao 26a3cb93c7 component/soc : move dport access header files to soc
1. move dport access header files to soc
2. reduce dport register write protection. Only protect read operation
2017-05-09 18:06:00 +08:00

295 lines
9.9 KiB
C

#include <esp_types.h>
#include <stdio.h>
#include <stdlib.h>
#include "rom/ets_sys.h"
#include "rom/lldesc.h"
#include "rom/gpio.h"
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "freertos/semphr.h"
#include "freertos/queue.h"
#include "freertos/xtensa_api.h"
#include "unity.h"
#include "soc/uart_reg.h"
#include "soc/dport_reg.h"
#include "soc/io_mux_reg.h"
#include "soc/gpio_sig_map.h"
#include "soc/gpio_reg.h"
#include "soc/i2s_reg.h"
#define DPORT_I2S0_CLK_EN (BIT(4))
#define DPORT_I2S0_RST (BIT(4))
/*
This test tests the s32c1i instruction when the AHB bus is also used. To create some AHB traffic, we use the I2S interface
to copy bytes over from one memory location to another. DO NOT USE the i2s routines inhere, they've been trial-and-error'ed until
the point where they happened to do what I want.
*/
static void lcdIfaceInit()
{
DPORT_SET_PERI_REG_MASK(DPORT_PERIP_CLK_EN_REG, DPORT_I2S0_CLK_EN);
DPORT_CLEAR_PERI_REG_MASK(DPORT_PERIP_RST_EN_REG, DPORT_I2S0_RST);
//Init pins to i2s functions
SET_PERI_REG_MASK(GPIO_ENABLE_W1TS_REG, (1 << 11) | (1 << 3) | (1 << 0) | (1 << 2) | (1 << 5) | (1 << 16) | (1 << 17) | (1 << 18) | (1 << 19) | (1 << 20)); //ENABLE GPIO oe_enable
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO0_U, 0);
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO2_U, 0);
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO5_U, 0);
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO16_U, 0);
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO17_U, 0);
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO18_U, 0);
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO19_U, 0);
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO20_U, 0);
PIN_FUNC_SELECT(PERIPHS_IO_MUX_SD_CMD_U, 2); //11
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO26_U, 0); //RS
WRITE_PERI_REG(GPIO_FUNC0_OUT_SEL_CFG_REG, (148 << GPIO_FUNC0_OUT_SEL_S));
WRITE_PERI_REG(GPIO_FUNC2_OUT_SEL_CFG_REG, (149 << GPIO_FUNC0_OUT_SEL_S));
WRITE_PERI_REG(GPIO_FUNC5_OUT_SEL_CFG_REG, (150 << GPIO_FUNC0_OUT_SEL_S));
WRITE_PERI_REG(GPIO_FUNC16_OUT_SEL_CFG_REG, (151 << GPIO_FUNC0_OUT_SEL_S));
WRITE_PERI_REG(GPIO_FUNC17_OUT_SEL_CFG_REG, (152 << GPIO_FUNC0_OUT_SEL_S));
WRITE_PERI_REG(GPIO_FUNC18_OUT_SEL_CFG_REG, (153 << GPIO_FUNC0_OUT_SEL_S));
WRITE_PERI_REG(GPIO_FUNC19_OUT_SEL_CFG_REG, (154 << GPIO_FUNC0_OUT_SEL_S));
WRITE_PERI_REG(GPIO_FUNC20_OUT_SEL_CFG_REG, (155 << GPIO_FUNC0_OUT_SEL_S));
WRITE_PERI_REG(GPIO_FUNC26_OUT_SEL_CFG_REG, (156 << GPIO_FUNC0_OUT_SEL_S)); //RS
WRITE_PERI_REG(GPIO_FUNC11_OUT_SEL_CFG_REG, (I2S0O_WS_OUT_IDX << GPIO_FUNC0_OUT_SEL_S));
// WRITE_PERI_REG(GPIO_FUNC11_OUT_SEL_CFG, (I2S0O_BCK_OUT_IDX<<GPIO_GPIO_FUNC0_OUT_SEL_S));
//GPIO_SET_GPIO_FUNC11_OUT_INV_SEL(1); //old
WRITE_PERI_REG(GPIO_FUNC11_OUT_SEL_CFG_REG, READ_PERI_REG(GPIO_FUNC11_OUT_SEL_CFG_REG) | GPIO_FUNC11_OUT_INV_SEL);
//Reset I2S subsystem
CLEAR_PERI_REG_MASK(I2S_CONF_REG(0), I2S_RX_RESET | I2S_TX_RESET);
SET_PERI_REG_MASK(I2S_CONF_REG(0), I2S_RX_RESET | I2S_TX_RESET);
CLEAR_PERI_REG_MASK(I2S_CONF_REG(0), I2S_RX_RESET | I2S_TX_RESET);
WRITE_PERI_REG(I2S_CONF_REG(0), 0);//I2S_SIG_LOOPBACK);
WRITE_PERI_REG(I2S_CONF2_REG(0), 0);
WRITE_PERI_REG(I2S_SAMPLE_RATE_CONF_REG(0),
(16 << I2S_RX_BITS_MOD_S) |
(16 << I2S_TX_BITS_MOD_S) |
(1 << I2S_RX_BCK_DIV_NUM_S) |
(1 << I2S_TX_BCK_DIV_NUM_S));
WRITE_PERI_REG(I2S_CLKM_CONF_REG(0),
I2S_CLKA_ENA | I2S_CLK_EN |
(1 << I2S_CLKM_DIV_A_S) |
(1 << I2S_CLKM_DIV_B_S) |
(1 << I2S_CLKM_DIV_NUM_S));
WRITE_PERI_REG(I2S_FIFO_CONF_REG(0),
(32 << I2S_TX_DATA_NUM_S) | //Low watermark for IRQ
(32 << I2S_RX_DATA_NUM_S));
WRITE_PERI_REG(I2S_CONF1_REG(0), I2S_RX_PCM_BYPASS | I2S_TX_PCM_BYPASS);
WRITE_PERI_REG(I2S_CONF_CHAN_REG(0), (2 << I2S_TX_CHAN_MOD_S) | (2 << I2S_RX_CHAN_MOD_S));
//Invert WS to active-low
SET_PERI_REG_MASK(I2S_CONF_REG(0), I2S_TX_RIGHT_FIRST | I2S_RX_RIGHT_FIRST);
WRITE_PERI_REG(I2S_TIMING_REG(0), 0);
}
static volatile lldesc_t dmaDesc[2];
static void finishDma()
{
//No need to finish if no DMA transfer going on
if (!(READ_PERI_REG(I2S_FIFO_CONF_REG(0))&I2S_DSCR_EN)) {
return;
}
//Wait till fifo done
while (!(READ_PERI_REG(I2S_INT_RAW_REG(0))&I2S_TX_REMPTY_INT_RAW)) ;
//Wait for last bytes to leave i2s xmit thing
//ToDo: poll bit in next hw
// for (i=0; i<(1<<8); i++);
while (!(READ_PERI_REG(I2S_STATE_REG(0))&I2S_TX_IDLE));
//Reset I2S for next transfer
CLEAR_PERI_REG_MASK(I2S_CONF_REG(0), I2S_TX_START | I2S_RX_START);
CLEAR_PERI_REG_MASK(I2S_OUT_LINK_REG(0), I2S_OUTLINK_START | I2S_INLINK_START);
SET_PERI_REG_MASK(I2S_CONF_REG(0), I2S_TX_RESET | I2S_TX_FIFO_RESET | I2S_RX_RESET | I2S_RX_FIFO_RESET);
CLEAR_PERI_REG_MASK(I2S_CONF_REG(0), I2S_TX_RESET | I2S_TX_FIFO_RESET | I2S_RX_RESET | I2S_RX_FIFO_RESET);
// for (i=0; i<(1<<8); i++);
while ((READ_PERI_REG(I2S_STATE_REG(0))&I2S_TX_FIFO_RESET_BACK));
}
/*
This is a very, very, very hacked up LCD routine which ends up basically doing a memcpy from sbuf to rbuf.
*/
static void sendRecvBufDma(uint16_t *sbuf, uint16_t *rbuf, int len)
{
//Fill DMA descriptor
dmaDesc[0].length = len * 2;
dmaDesc[0].size = len * 2;
dmaDesc[0].owner = 1;
dmaDesc[0].sosf = 0;
dmaDesc[0].buf = (uint8_t *)sbuf;
dmaDesc[0].offset = 0; //unused in hw
dmaDesc[0].empty = 0;
dmaDesc[0].eof = 1;
dmaDesc[1].length = len * 2;
dmaDesc[1].size = len * 2;
dmaDesc[1].owner = 1;
dmaDesc[1].sosf = 0;
dmaDesc[1].buf = (uint8_t *)rbuf;
dmaDesc[1].offset = 0; //unused in hw
dmaDesc[1].empty = 0;
dmaDesc[1].eof = 1;
//Reset DMA
SET_PERI_REG_MASK(I2S_LC_CONF_REG(0), I2S_IN_RST | I2S_OUT_RST | I2S_AHBM_RST | I2S_AHBM_FIFO_RST);
CLEAR_PERI_REG_MASK(I2S_LC_CONF_REG(0), I2S_IN_RST | I2S_OUT_RST | I2S_AHBM_RST | I2S_AHBM_FIFO_RST);
//Reset I2S FIFO
SET_PERI_REG_MASK(I2S_CONF_REG(0), I2S_RX_RESET | I2S_TX_RESET | I2S_TX_FIFO_RESET | I2S_RX_FIFO_RESET);
CLEAR_PERI_REG_MASK(I2S_CONF_REG(0), I2S_RX_RESET | I2S_TX_RESET | I2S_TX_FIFO_RESET | I2S_RX_FIFO_RESET);
//Set desc addr
CLEAR_PERI_REG_MASK(I2S_OUT_LINK_REG(0), I2S_OUTLINK_ADDR);
SET_PERI_REG_MASK(I2S_OUT_LINK_REG(0), ((uint32_t)(&dmaDesc[0]))&I2S_OUTLINK_ADDR);
CLEAR_PERI_REG_MASK(I2S_IN_LINK_REG(0), I2S_INLINK_ADDR);
SET_PERI_REG_MASK(I2S_IN_LINK_REG(0), ((uint32_t)(&dmaDesc[1]))&I2S_INLINK_ADDR);
SET_PERI_REG_MASK(I2S_FIFO_CONF_REG(0), I2S_DSCR_EN); //Enable DMA mode
WRITE_PERI_REG(I2S_RXEOF_NUM_REG(0), len);
//Enable and configure DMA
WRITE_PERI_REG(I2S_LC_CONF_REG(0), I2S_OUT_DATA_BURST_EN |
I2S_OUT_EOF_MODE | I2S_OUTDSCR_BURST_EN | I2S_OUT_DATA_BURST_EN |
I2S_INDSCR_BURST_EN | I2S_MEM_TRANS_EN);
//Start transmission
SET_PERI_REG_MASK(I2S_OUT_LINK_REG(0), I2S_OUTLINK_START);
SET_PERI_REG_MASK(I2S_IN_LINK_REG(0), I2S_INLINK_START);
SET_PERI_REG_MASK(I2S_CONF_REG(0), I2S_TX_START | I2S_RX_START);
//Clear int flags
WRITE_PERI_REG(I2S_INT_CLR_REG(0), 0xFFFFFFFF);
}
#define DMALEN (2048-2)
static void tskLcd(void *pvParameters)
{
uint16_t *sbuf = malloc(DMALEN * 2);
uint16_t *rbuf = malloc(DMALEN * 2);
uint16_t xorval = 0;
int x;
lcdIfaceInit();
// lcdFlush();
while (1) {
for (x = 0; x < DMALEN; x++) {
sbuf[x] = x ^ xorval;
}
for (x = 0; x < DMALEN; x++) {
rbuf[x] = 0; //clear rbuf
}
sendRecvBufDma(sbuf, rbuf, DMALEN);
vTaskDelay(20 / portTICK_PERIOD_MS);
finishDma();
for (x = 0; x < DMALEN; x++) if (rbuf[x] != (x ^ xorval)) {
printf("Rxbuf err! pos %d val %x xor %x", x, (int)rbuf[x], (int)xorval);
}
printf(".");
fflush(stdout);
xorval++;
}
}
void test_s32c1i_lock(volatile int *lockvar, int lockval, int unlockval, volatile int *ctr);
static volatile int ctr = 0, state = 0;
static volatile int lock = 0;
static void tskOne(void *pvParameters)
{
int x;
int err = 0, run = 0;
while (1) {
ctr = 0; lock = 0;
state = 1;
for (x = 0; x < 16 * 1024; x++) {
test_s32c1i_lock(&lock, 1, 0, &ctr);
}
vTaskDelay(60 / portTICK_PERIOD_MS);
state = 2;
if (ctr != 16 * 1024 * 2) {
printf("Lock malfunction detected! Ctr=0x%x instead of %x\n", ctr, 16 * 1024 * 2);
err++;
}
run++;
printf("Run %d err %d\n", run, err);
vTaskDelay(20 / portTICK_PERIOD_MS);
}
}
#define FB2ADDR 0x40098000
static void tskTwo(void *pvParameters)
{
int x;
int *p = (int *)FB2ADDR;
int *s = (int *)test_s32c1i_lock;
void (*test_s32c1i_lock2)(volatile int * lockvar, int lockval, int unlockval, volatile int * ctr) = (void *)FB2ADDR;
volatile int w;
int delay;
for (x = 0; x < 100; x++) {
*p++ = *s++; //copy routine to different pool
}
while (1) {
while (state != 1) ;
for (x = 0; x < 16 * 1024; x++) {
test_s32c1i_lock2(&lock, 2, 0, &ctr);
//Some random delay to increase chance of weirdness
if ((x & 0x1f) == 0) {
delay = rand() & 0x1f;
for (w = 0; w < delay; w++);
}
}
while (state != 2);
}
}
TEST_CASE("S32C1I vs AHB test (needs I2S)", "[hw][ignore]")
{
int i;
TaskHandle_t th[3];
state = 0;
printf("Creating tasks\n");
xTaskCreatePinnedToCore(tskTwo , "tsktwo" , 2048, NULL, 3, &th[1], 1);
xTaskCreatePinnedToCore(tskOne , "tskone" , 2048, NULL, 3, &th[0], 0);
xTaskCreatePinnedToCore(tskLcd , "tsklcd" , 2048, NULL, 3, &th[2], 0);
// Let stuff run for 20s
while (1) {
vTaskDelay(20000 / portTICK_PERIOD_MS);
}
//Shut down all the tasks
for (i = 0; i < 3; i++) {
vTaskDelete(th[i]);
}
}