esp-idf/examples/bluetooth/esp_hid_device
2024-08-21 19:27:36 +08:00
..
main fix(ble/bluedroid): Fixed memory out-of-bounds issue when parsing adv data 2024-08-21 19:27:36 +08:00
CMakeLists.txt tools: Increase the minimal supported CMake version to 3.16 2022-06-01 06:35:02 +00:00
README.md feat(ble): support ble on esp32c5 2024-07-23 20:12:43 +08:00
sdkconfig.defaults fix(example/bluetooth): fix app partition is to small for binary esp_hid_device.bin and esp_hid_host.bin 2024-03-30 11:51:52 +08:00
sdkconfig.defaults.esp32c3 1. update esp_hid component to use esp HID API 2021-09-08 14:08:34 +08:00
sdkconfig.defaults.esp32s3 1. update esp_hid component to use esp HID API 2021-09-08 14:08:34 +08:00

Supported Targets ESP32 ESP32-C2 ESP32-C3 ESP32-C5 ESP32-C6 ESP32-H2 ESP32-S3

ESP-IDF BT/BLE HID Device Demo

This demo use APIs which esp_hid component provided to create a BT, BLE or Bluetooth dual mode hid device. Users can choose mode by setting HID_DEV_MODE.

This example works in companion with the BLE HID Host Example

How to Use Example

Before project configuration and build, be sure to set the correct chip target using:

idf.py set-target <chip_name>

The BT hid device plays as a mouse. When the connection is successfully established, users can follow the usage below to operate the 'mouse'.

########################################################################
BT hid mouse demo usage:
You can input these value to simulate mouse: 'q', 'w', 'e', 'a', 's', 'd', 'h'
q -- click the left key
w -- move up
e -- click the right key
a -- move left
s -- move down
d -- move right
h -- show the help
########################################################################

The BLE hid device plays as a remote control. When the connection is successfully established, the remote control will set volume up and down periodically. This example implements a BLE HID device.

Hardware Required

  • A development board with ESP32 SoC (e.g., ESP32-DevKitC, ESP-WROVER-KIT, etc.)
  • A USB cable for Power supply and programming

See Development Boards for more information about it.

Configure the Project

Build and Flash

Build the project and flash it to the board, then run monitor tool to view serial output.

idf.py -p PORT flash monitor

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

I (0) cpu_start: Starting scheduler on APP CPU.
I (607) BTDM_INIT: BT controller compile version [d03a5d3]
I (607) system_api: Base MAC address is not set
I (607) system_api: read default base MAC address from EFUSE
I (617) phy_init: phy_version 4670,719f9f6,Feb 18 2021,17:07:07
W (1337) BT_BTM: BTM_BleWriteAdvData, Partial data write into ADV
I (1357) HID_DEV_DEMO: START
I (25067) HID_DEV_DEMO: CONNECT
I (25357) HID_DEV_DEMO: Send the volume
E (25437) BT_SMP: Value for numeric comparison = 125657
I (25437) ESP_HID_GAP: BLE GAP NC_REQ passkey:125657
W (25517) BT_SMP: FOR LE SC LTK IS USED INSTEAD OF STK
I (25587) ESP_HID_GAP: BLE GAP KEY type = ESP_LE_KEY_LENC
I (25587) ESP_HID_GAP: BLE GAP KEY type = ESP_LE_KEY_PENC
I (25587) ESP_HID_GAP: BLE GAP KEY type = ESP_LE_KEY_LID
I (25647) ESP_HID_GAP: BLE GAP KEY type = ESP_LE_KEY_PID
I (25757) ESP_HID_GAP: BLE GAP AUTH SUCCESS
I (27457) HID_DEV_DEMO: Send the volume
I (29557) HID_DEV_DEMO: Send the volume
I (31657) HID_DEV_DEMO: Send the volume
I (33757) HID_DEV_DEMO: Send the volume
I (35857) HID_DEV_DEMO: Send the volume
I (37957) HID_DEV_DEMO: Send the volume
I (40057) HID_DEV_DEMO: Send the volume
I (42157) HID_DEV_DEMO: Send the volume
I (44257) HID_DEV_DEMO: Send the volume
I (46357) HID_DEV_DEMO: Send the volume
I (48457) HID_DEV_DEMO: Send the volume
I (50557) HID_DEV_DEMO: Send the volume
...

Troubleshooting

For any technical queries, please open an issue on GitHub. We will get back to you soon.