esp-idf/components/soc/esp32s2beta/include/hal/ledc_ll.h
chenjianqiang 857dec108d feat(ledc): refactor ledc driver
1. add hal and low-level layer for ledc driver
2. support esp32s2beta ledc
2019-11-21 16:25:22 +08:00

480 lines
18 KiB
C

// Copyright 2019 Espressif Systems (Shanghai) PTE LTD
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// The LL layer for LEDC register operations.
// Note that most of the register operations in this layer are non-atomic operations.
#pragma once
#include "hal/ledc_types.h"
#include "soc/ledc_periph.h"
#define LEDC_LL_GET_HW() &LEDC
/**
* @brief Set LEDC low speed timer clock
*
* @param hw Beginning address of the peripheral registers
* @param slow_clk_sel LEDC low speed timer clock source
*
* @return None
*/
static inline void ledc_ll_set_slow_clk_sel(ledc_dev_t *hw, ledc_slow_clk_sel_t slow_clk_sel){
uint32_t clk_sel_val = 0;
if (slow_clk_sel == LEDC_SLOW_CLK_APB) {
clk_sel_val = 1;
} else if (slow_clk_sel == LEDC_SLOW_CLK_RTC8M) {
clk_sel_val = 2;
} else if (slow_clk_sel == LEDC_SLOW_CLK_XTAL) {
clk_sel_val = 3;
}
hw->conf.apb_clk_sel = clk_sel_val;
}
/**
* @brief Get LEDC low speed timer clock
*
* @param hw Beginning address of the peripheral registers
* @param slow_clk_sel LEDC low speed timer clock source
*
* @return None
*/
static inline void ledc_ll_get_slow_clk_sel(ledc_dev_t *hw, ledc_slow_clk_sel_t *slow_clk_sel){
uint32_t clk_sel_val = hw->conf.apb_clk_sel;
if (clk_sel_val == 1) {
*slow_clk_sel = LEDC_SLOW_CLK_APB;
} else if (clk_sel_val == 2) {
*slow_clk_sel = LEDC_SLOW_CLK_RTC8M;
} else if (clk_sel_val == 3) {
*slow_clk_sel = LEDC_SLOW_CLK_XTAL;
}
}
/**
* @brief Update LEDC low speed timer
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param timer_sel LEDC timer index (0-3), select from ledc_timer_t
*
* @return None
*/
static inline void ledc_ll_ls_timer_update(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_timer_t timer_sel){
hw->timer_group[speed_mode].timer[timer_sel].conf.low_speed_update = 1;
}
/**
* @brief Reset LEDC timer
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param timer_sel LEDC timer index (0-3), select from ledc_timer_t
*
* @return None
*/
static inline void ledc_ll_timer_rst(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_timer_t timer_sel){
hw->timer_group[speed_mode].timer[timer_sel].conf.rst = 1;
hw->timer_group[speed_mode].timer[timer_sel].conf.rst = 0;
}
/**
* @brief Pause LEDC timer
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param timer_sel LEDC timer index (0-3), select from ledc_timer_t
*
* @return None
*/
static inline void ledc_ll_timer_pause(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_timer_t timer_sel){
hw->timer_group[speed_mode].timer[timer_sel].conf.pause = 1;
}
/**
* @brief Resume LEDC timer
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param timer_sel LEDC timer index (0-3), select from ledc_timer_t
*
* @return None
*/
static inline void ledc_ll_timer_resume(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_timer_t timer_sel){
hw->timer_group[speed_mode].timer[timer_sel].conf.pause = 0;
}
/**
* @brief Set LEDC timer clock divider
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param timer_sel LEDC timer index (0-3), select from ledc_timer_t
* @param clock_divider Timer clock divide value, the timer clock is divided from the selected clock source
*
* @return None
*/
static inline void ledc_ll_set_clock_divider(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_timer_t timer_sel, uint32_t clock_divider){
hw->timer_group[speed_mode].timer[timer_sel].conf.clock_divider = clock_divider;
}
/**
* @brief Get LEDC timer clock divider
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param timer_sel LEDC timer index (0-3), select from ledc_timer_t
* @param clock_divider Timer clock divide value, the timer clock is divided from the selected clock source
*
* @return None
*/
static inline void ledc_ll_get_clock_divider(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_timer_t timer_sel, uint32_t *clock_divider){
*clock_divider = hw->timer_group[speed_mode].timer[timer_sel].conf.clock_divider;
}
/**
* @brief Set LEDC timer clock source
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param timer_sel LEDC timer index (0-3), select from ledc_timer_t
* @param clk_src Timer clock source
*
* @return None
*/
static inline void ledc_ll_set_clock_source(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_timer_t timer_sel, ledc_clk_src_t clk_src){
if (clk_src == LEDC_REF_TICK) {
//REF_TICK can only be used when APB is selected.
hw->timer_group[speed_mode].timer[timer_sel].conf.tick_sel = 1;
hw->conf.apb_clk_sel = 1;
} else {
hw->timer_group[speed_mode].timer[timer_sel].conf.tick_sel = 0;
}
}
/**
* @brief Get LEDC timer clock source
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param timer_sel LEDC timer index (0-3), select from ledc_timer_t
* @param clk_src Pointer to accept the timer clock source
*
* @return None
*/
static inline void ledc_ll_get_clock_source(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_timer_t timer_sel, ledc_clk_src_t *clk_src){
if (hw->timer_group[speed_mode].timer[timer_sel].conf.tick_sel == 1) {
*clk_src = LEDC_REF_TICK;
} else {
*clk_src = LEDC_APB_CLK;
}
}
/**
* @brief Set LEDC duty resolution
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param timer_sel LEDC timer index (0-3), select from ledc_timer_t
* @param duty_resolution Resolution of duty setting in number of bits. The range of duty values is [0, (2**duty_resolution)]
*
* @return None
*/
static inline void ledc_ll_set_duty_resolution(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_timer_t timer_sel, uint32_t duty_resolution){
hw->timer_group[speed_mode].timer[timer_sel].conf.duty_resolution = duty_resolution;
}
/**
* @brief Get LEDC duty resolution
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param timer_sel LEDC timer index (0-3), select from ledc_timer_t
* @param duty_resolution Pointer to accept the resolution of duty setting in number of bits.
*
* @return None
*/
static inline void ledc_ll_get_duty_resolution(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_timer_t timer_sel, uint32_t *duty_resolution){
*duty_resolution = hw->timer_group[speed_mode].timer[timer_sel].conf.duty_resolution;
}
/**
* @brief Update channel configure when select low speed mode
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
*
* @return None
*/
static inline void ledc_ll_ls_channel_update(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num){
hw->channel_group[speed_mode].channel[channel_num].conf0.low_speed_update = 1;
}
/**
* @brief Get LEDC max duty
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param max_duty Pointer to accept the max duty
*
* @return None
*/
static inline void ledc_ll_get_max_duty(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, uint32_t *max_duty){
uint32_t timer_sel = hw->channel_group[speed_mode].channel[channel_num].conf0.timer_sel;
*max_duty = (1 << (LEDC.timer_group[speed_mode].timer[timer_sel].conf.duty_resolution));
}
/**
* @brief Set LEDC hpoint value
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param hpoint_val LEDC hpoint value(max: 0xfffff)
*
* @return None
*/
static inline void ledc_ll_set_hpoint(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, uint32_t hpoint_val){
hw->channel_group[speed_mode].channel[channel_num].hpoint.hpoint = hpoint_val;
}
/**
* @brief Get LEDC hpoint value
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param hpoint_val Pointer to accept the LEDC hpoint value(max: 0xfffff)
*
* @return None
*/
static inline void ledc_ll_get_hpoint(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, uint32_t *hpoint_val){
*hpoint_val = hw->channel_group[speed_mode].channel[channel_num].hpoint.hpoint;
}
/**
* @brief Set LEDC the integer part of duty value
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param duty_val LEDC duty value, the range of duty setting is [0, (2**duty_resolution)]
*
* @return None
*/
static inline void ledc_ll_set_duty_int_part(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, uint32_t duty_val){
hw->channel_group[speed_mode].channel[channel_num].duty.duty = duty_val << 4;
}
/**
* @brief Get LEDC duty value
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param duty_val Pointer to accept the LEDC duty value
*
* @return None
*/
static inline void ledc_ll_get_duty(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, uint32_t *duty_val){
*duty_val = (hw->channel_group[speed_mode].channel[channel_num].duty_rd.duty_read >> 4);
}
/**
* @brief Set LEDC duty change direction
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param duty_direction LEDC duty change direction, increase or decrease
*
* @return None
*/
static inline void ledc_ll_set_duty_direction(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, ledc_duty_direction_t duty_direction){
hw->channel_group[speed_mode].channel[channel_num].conf1.duty_inc = duty_direction;
}
/**
* @brief Get LEDC duty change direction
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param duty_direction Pointer to accept the LEDC duty change direction, increase or decrease
*
* @return None
*/
static inline void ledc_ll_get_duty_direction(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, ledc_duty_direction_t *duty_direction){
*duty_direction = hw->channel_group[speed_mode].channel[channel_num].conf1.duty_inc;
}
/**
* @brief Set the number of increased or decreased times
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param duty_num The number of increased or decreased times
*
* @return None
*/
static inline void ledc_ll_set_duty_num(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, uint32_t duty_num){
hw->channel_group[speed_mode].channel[channel_num].conf1.duty_num = duty_num;
}
/**
* @brief Set the duty cycles of increase or decrease
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param duty_cycle The duty cycles
*
* @return None
*/
static inline void ledc_ll_set_duty_cycle(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, uint32_t duty_cycle){
hw->channel_group[speed_mode].channel[channel_num].conf1.duty_cycle = duty_cycle;
}
/**
* @brief Set the step scale of increase or decrease
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param duty_scale The step scale
*
* @return None
*/
static inline void ledc_ll_set_duty_scale(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, uint32_t duty_scale){
hw->channel_group[speed_mode].channel[channel_num].conf1.duty_scale = duty_scale;
}
/**
* @brief Set the output enable
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param sig_out_en The output enable status
*
* @return None
*/
static inline void ledc_ll_set_sig_out_en(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, bool sig_out_en){
hw->channel_group[speed_mode].channel[channel_num].conf0.sig_out_en = sig_out_en;
}
/**
* @brief Set the duty start
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param duty_start The duty start
*
* @return None
*/
static inline void ledc_ll_set_duty_start(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, bool duty_start){
hw->channel_group[speed_mode].channel[channel_num].conf1.duty_start = duty_start;
}
/**
* @brief Set output idle level
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param idle_level The output idle level
*
* @return None
*/
static inline void ledc_ll_set_idle_level(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, uint32_t idle_level){
hw->channel_group[speed_mode].channel[channel_num].conf0.idle_lv = idle_level & 0x1;
}
/**
* @brief Set fade end interrupt enable
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param fade_end_intr_en The fade end interrupt enable status
*
* @return None
*/
static inline void ledc_ll_set_fade_end_intr(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, bool fade_end_intr_en){
uint32_t value = hw->int_ena.val;
uint32_t int_en_base = LEDC_DUTY_CHNG_END_LSCH0_INT_ENA_S;
hw->int_ena.val = fade_end_intr_en ? (value | BIT(int_en_base + channel_num)) : (value & (~(BIT(int_en_base + channel_num))));
}
/**
* @brief Get fade end interrupt status
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param intr_status The fade end interrupt status
*
* @return None
*/
static inline void ledc_ll_get_fade_end_intr_status(ledc_dev_t *hw, ledc_mode_t speed_mode, uint32_t *intr_status){
uint32_t value = hw->int_st.val;
uint32_t int_en_base = LEDC_DUTY_CHNG_END_LSCH0_INT_ENA_S;
*intr_status = (value >> int_en_base) & 0xff;
}
/**
* @brief Clear fade end interrupt status
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
*
* @return None
*/
static inline void ledc_ll_clear_fade_end_intr_status(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num){
uint32_t int_en_base = LEDC_DUTY_CHNG_END_LSCH0_INT_ENA_S;
hw->int_clr.val = BIT(int_en_base + channel_num);
}
/**
* @brief Set timer index of the specified channel
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param timer_sel LEDC timer index (0-3), select from ledc_timer_t
*
* @return None
*/
static inline void ledc_ll_bind_channel_timer(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, ledc_timer_t timer_sel){
hw->channel_group[speed_mode].channel[channel_num].conf0.timer_sel = timer_sel;
}
/**
* @brief Get timer index of the specified channel
*
* @param hw Beginning address of the peripheral registers
* @param speed_mode LEDC speed_mode, high-speed mode or low-speed mode
* @param channel_num LEDC channel index (0-7), select from ledc_channel_t
* @param timer_sel Pointer to accept the LEDC timer index
*
* @return None
*/
static inline void ledc_ll_get_channel_timer(ledc_dev_t *hw, ledc_mode_t speed_mode, ledc_channel_t channel_num, ledc_timer_t *timer_sel){
*timer_sel = hw->channel_group[speed_mode].channel[channel_num].conf0.timer_sel;
}