mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
b8e62ce4b2
In previous transmission(s), the TX_DONE interrupt raw bit may be raised, but never been cleared. TX_DONE interrrupt status bit should be cleared before enabling it to check the new transmission.
1782 lines
79 KiB
C
1782 lines
79 KiB
C
// Copyright 2015-2019 Espressif Systems (Shanghai) PTE LTD
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
#include <string.h>
|
|
#include <sys/param.h>
|
|
#include "esp_types.h"
|
|
#include "esp_attr.h"
|
|
#include "esp_intr_alloc.h"
|
|
#include "esp_log.h"
|
|
#include "esp_err.h"
|
|
#include "malloc.h"
|
|
#include "freertos/FreeRTOS.h"
|
|
#include "freertos/semphr.h"
|
|
#include "freertos/ringbuf.h"
|
|
#include "hal/uart_hal.h"
|
|
#include "hal/gpio_hal.h"
|
|
#include "soc/uart_periph.h"
|
|
#include "soc/rtc_cntl_reg.h"
|
|
#include "driver/uart.h"
|
|
#include "driver/gpio.h"
|
|
#include "driver/uart_select.h"
|
|
#include "driver/periph_ctrl.h"
|
|
#include "sdkconfig.h"
|
|
#include "esp_rom_gpio.h"
|
|
|
|
#if CONFIG_IDF_TARGET_ESP32
|
|
#include "esp32/clk.h"
|
|
#elif CONFIG_IDF_TARGET_ESP32S2
|
|
#include "esp32s2/clk.h"
|
|
#elif CONFIG_IDF_TARGET_ESP32S3
|
|
#include "esp32s3/clk.h"
|
|
#elif CONFIG_IDF_TARGET_ESP32C3
|
|
#include "esp32c3/clk.h"
|
|
#endif
|
|
|
|
#ifdef CONFIG_UART_ISR_IN_IRAM
|
|
#define UART_ISR_ATTR IRAM_ATTR
|
|
#define UART_MALLOC_CAPS (MALLOC_CAP_INTERNAL | MALLOC_CAP_8BIT)
|
|
#else
|
|
#define UART_ISR_ATTR
|
|
#define UART_MALLOC_CAPS MALLOC_CAP_DEFAULT
|
|
#endif
|
|
|
|
#define XOFF (0x13)
|
|
#define XON (0x11)
|
|
|
|
static const char *UART_TAG = "uart";
|
|
#define UART_CHECK(a, str, ret_val) \
|
|
if (!(a)) { \
|
|
ESP_LOGE(UART_TAG,"%s(%d): %s", __FUNCTION__, __LINE__, str); \
|
|
return (ret_val); \
|
|
}
|
|
|
|
#define UART_EMPTY_THRESH_DEFAULT (10)
|
|
#define UART_FULL_THRESH_DEFAULT (120)
|
|
#define UART_TOUT_THRESH_DEFAULT (10)
|
|
#define UART_CLKDIV_FRAG_BIT_WIDTH (3)
|
|
#define UART_TX_IDLE_NUM_DEFAULT (0)
|
|
#define UART_PATTERN_DET_QLEN_DEFAULT (10)
|
|
#define UART_MIN_WAKEUP_THRESH (UART_LL_MIN_WAKEUP_THRESH)
|
|
|
|
#define UART_INTR_CONFIG_FLAG ((UART_INTR_RXFIFO_FULL) \
|
|
| (UART_INTR_RXFIFO_TOUT) \
|
|
| (UART_INTR_RXFIFO_OVF) \
|
|
| (UART_INTR_BRK_DET) \
|
|
| (UART_INTR_PARITY_ERR))
|
|
|
|
|
|
#define UART_ENTER_CRITICAL_SAFE(mux) portENTER_CRITICAL_SAFE(mux)
|
|
#define UART_EXIT_CRITICAL_SAFE(mux) portEXIT_CRITICAL_SAFE(mux)
|
|
#define UART_ENTER_CRITICAL_ISR(mux) portENTER_CRITICAL_ISR(mux)
|
|
#define UART_EXIT_CRITICAL_ISR(mux) portEXIT_CRITICAL_ISR(mux)
|
|
#define UART_ENTER_CRITICAL(mux) portENTER_CRITICAL(mux)
|
|
#define UART_EXIT_CRITICAL(mux) portEXIT_CRITICAL(mux)
|
|
|
|
|
|
// Check actual UART mode set
|
|
#define UART_IS_MODE_SET(uart_number, mode) ((p_uart_obj[uart_number]->uart_mode == mode))
|
|
|
|
#define UART_CONTEX_INIT_DEF(uart_num) {\
|
|
.hal.dev = UART_LL_GET_HW(uart_num),\
|
|
.spinlock = portMUX_INITIALIZER_UNLOCKED,\
|
|
.hw_enabled = false,\
|
|
}
|
|
|
|
#if SOC_UART_SUPPORT_RTC_CLK
|
|
#define RTC_ENABLED(uart_num) (BIT(uart_num))
|
|
#endif
|
|
|
|
typedef struct {
|
|
uart_event_type_t type; /*!< UART TX data type */
|
|
struct {
|
|
int brk_len;
|
|
size_t size;
|
|
uint8_t data[0];
|
|
} tx_data;
|
|
} uart_tx_data_t;
|
|
|
|
typedef struct {
|
|
int wr;
|
|
int rd;
|
|
int len;
|
|
int *data;
|
|
} uart_pat_rb_t;
|
|
|
|
typedef struct {
|
|
uart_port_t uart_num; /*!< UART port number*/
|
|
int event_queue_size; /*!< UART event queue size*/
|
|
intr_handle_t intr_handle; /*!< UART interrupt handle*/
|
|
uart_mode_t uart_mode; /*!< UART controller actual mode set by uart_set_mode() */
|
|
bool coll_det_flg; /*!< UART collision detection flag */
|
|
bool rx_always_timeout_flg; /*!< UART always detect rx timeout flag */
|
|
int rx_buffered_len; /*!< UART cached data length */
|
|
int rx_buf_size; /*!< RX ring buffer size */
|
|
bool rx_buffer_full_flg; /*!< RX ring buffer full flag. */
|
|
uint32_t rx_cur_remain; /*!< Data number that waiting to be read out in ring buffer item*/
|
|
uint8_t *rx_ptr; /*!< pointer to the current data in ring buffer*/
|
|
uint8_t *rx_head_ptr; /*!< pointer to the head of RX item*/
|
|
uint8_t rx_data_buf[SOC_UART_FIFO_LEN]; /*!< Data buffer to stash FIFO data*/
|
|
uint8_t rx_stash_len; /*!< stashed data length.(When using flow control, after reading out FIFO data, if we fail to push to buffer, we can just stash them.) */
|
|
uint32_t rx_int_usr_mask; /*!< RX interrupt status. Valid at any time, regardless of RX buffer status. */
|
|
uart_pat_rb_t rx_pattern_pos;
|
|
int tx_buf_size; /*!< TX ring buffer size */
|
|
bool tx_waiting_fifo; /*!< this flag indicates that some task is waiting for FIFO empty interrupt, used to send all data without any data buffer*/
|
|
uint8_t *tx_ptr; /*!< TX data pointer to push to FIFO in TX buffer mode*/
|
|
uart_tx_data_t *tx_head; /*!< TX data pointer to head of the current buffer in TX ring buffer*/
|
|
uint32_t tx_len_tot; /*!< Total length of current item in ring buffer*/
|
|
uint32_t tx_len_cur;
|
|
uint8_t tx_brk_flg; /*!< Flag to indicate to send a break signal in the end of the item sending procedure */
|
|
uint8_t tx_brk_len; /*!< TX break signal cycle length/number */
|
|
uint8_t tx_waiting_brk; /*!< Flag to indicate that TX FIFO is ready to send break signal after FIFO is empty, do not push data into TX FIFO right now.*/
|
|
uart_select_notif_callback_t uart_select_notif_callback; /*!< Notification about select() events */
|
|
QueueHandle_t event_queue; /*!< UART event queue handler*/
|
|
RingbufHandle_t rx_ring_buf; /*!< RX ring buffer handler*/
|
|
RingbufHandle_t tx_ring_buf; /*!< TX ring buffer handler*/
|
|
SemaphoreHandle_t rx_mux; /*!< UART RX data mutex*/
|
|
SemaphoreHandle_t tx_mux; /*!< UART TX mutex*/
|
|
SemaphoreHandle_t tx_fifo_sem; /*!< UART TX FIFO semaphore*/
|
|
SemaphoreHandle_t tx_done_sem; /*!< UART TX done semaphore*/
|
|
SemaphoreHandle_t tx_brk_sem; /*!< UART TX send break done semaphore*/
|
|
#if CONFIG_UART_ISR_IN_IRAM
|
|
void *event_queue_storage;
|
|
void *event_queue_struct;
|
|
void *rx_ring_buf_storage;
|
|
void *rx_ring_buf_struct;
|
|
void *tx_ring_buf_storage;
|
|
void *tx_ring_buf_struct;
|
|
void *rx_mux_struct;
|
|
void *tx_mux_struct;
|
|
void *tx_fifo_sem_struct;
|
|
void *tx_done_sem_struct;
|
|
void *tx_brk_sem_struct;
|
|
#endif
|
|
} uart_obj_t;
|
|
|
|
typedef struct {
|
|
uart_hal_context_t hal; /*!< UART hal context*/
|
|
portMUX_TYPE spinlock;
|
|
bool hw_enabled;
|
|
} uart_context_t;
|
|
|
|
static uart_obj_t *p_uart_obj[UART_NUM_MAX] = {0};
|
|
|
|
static uart_context_t uart_context[UART_NUM_MAX] = {
|
|
UART_CONTEX_INIT_DEF(UART_NUM_0),
|
|
UART_CONTEX_INIT_DEF(UART_NUM_1),
|
|
#if UART_NUM_MAX > 2
|
|
UART_CONTEX_INIT_DEF(UART_NUM_2),
|
|
#endif
|
|
};
|
|
|
|
static portMUX_TYPE uart_selectlock = portMUX_INITIALIZER_UNLOCKED;
|
|
|
|
#if SOC_UART_SUPPORT_RTC_CLK
|
|
|
|
static uint8_t rtc_enabled = 0;
|
|
static portMUX_TYPE rtc_num_spinlock = portMUX_INITIALIZER_UNLOCKED;
|
|
|
|
static void rtc_clk_enable(uart_port_t uart_num)
|
|
{
|
|
portENTER_CRITICAL(&rtc_num_spinlock);
|
|
if (!(rtc_enabled & RTC_ENABLED(uart_num))) {
|
|
rtc_enabled |= RTC_ENABLED(uart_num);
|
|
}
|
|
SET_PERI_REG_MASK(RTC_CNTL_CLK_CONF_REG, RTC_CNTL_DIG_CLK8M_EN_M);
|
|
portEXIT_CRITICAL(&rtc_num_spinlock);
|
|
}
|
|
|
|
static void rtc_clk_disable(uart_port_t uart_num)
|
|
{
|
|
assert(rtc_enabled & RTC_ENABLED(uart_num));
|
|
|
|
portENTER_CRITICAL(&rtc_num_spinlock);
|
|
rtc_enabled &= ~RTC_ENABLED(uart_num);
|
|
if (rtc_enabled == 0) {
|
|
CLEAR_PERI_REG_MASK(RTC_CNTL_CLK_CONF_REG, RTC_CNTL_DIG_CLK8M_EN_M);
|
|
}
|
|
portEXIT_CRITICAL(&rtc_num_spinlock);
|
|
}
|
|
#endif
|
|
|
|
static void uart_module_enable(uart_port_t uart_num)
|
|
{
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
if (uart_context[uart_num].hw_enabled != true) {
|
|
periph_module_enable(uart_periph_signal[uart_num].module);
|
|
if (uart_num != CONFIG_ESP_CONSOLE_UART_NUM) {
|
|
// Workaround for ESP32C3: enable core reset
|
|
// before enabling uart module clock
|
|
// to prevent uart output garbage value.
|
|
#if SOC_UART_REQUIRE_CORE_RESET
|
|
uart_hal_set_reset_core(&(uart_context[uart_num].hal), true);
|
|
periph_module_reset(uart_periph_signal[uart_num].module);
|
|
uart_hal_set_reset_core(&(uart_context[uart_num].hal), false);
|
|
#else
|
|
periph_module_reset(uart_periph_signal[uart_num].module);
|
|
#endif
|
|
}
|
|
uart_context[uart_num].hw_enabled = true;
|
|
}
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
}
|
|
|
|
static void uart_module_disable(uart_port_t uart_num)
|
|
{
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
if (uart_context[uart_num].hw_enabled != false) {
|
|
if (uart_num != CONFIG_ESP_CONSOLE_UART_NUM ) {
|
|
periph_module_disable(uart_periph_signal[uart_num].module);
|
|
}
|
|
uart_context[uart_num].hw_enabled = false;
|
|
}
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
}
|
|
|
|
esp_err_t uart_set_word_length(uart_port_t uart_num, uart_word_length_t data_bit)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((data_bit < UART_DATA_BITS_MAX), "data bit error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_data_bit_num(&(uart_context[uart_num].hal), data_bit);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_get_word_length(uart_port_t uart_num, uart_word_length_t *data_bit)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
uart_hal_get_data_bit_num(&(uart_context[uart_num].hal), data_bit);
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_stop_bits(uart_port_t uart_num, uart_stop_bits_t stop_bit)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((stop_bit < UART_STOP_BITS_MAX), "stop bit error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_stop_bits(&(uart_context[uart_num].hal), stop_bit);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_get_stop_bits(uart_port_t uart_num, uart_stop_bits_t *stop_bit)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_get_stop_bits(&(uart_context[uart_num].hal), stop_bit);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_parity(uart_port_t uart_num, uart_parity_t parity_mode)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_parity(&(uart_context[uart_num].hal), parity_mode);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_get_parity(uart_port_t uart_num, uart_parity_t *parity_mode)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_get_parity(&(uart_context[uart_num].hal), parity_mode);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_baudrate(uart_port_t uart_num, uint32_t baud_rate)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_baudrate(&(uart_context[uart_num].hal), baud_rate);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_get_baudrate(uart_port_t uart_num, uint32_t *baudrate)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_get_baudrate(&(uart_context[uart_num].hal), baudrate);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_line_inverse(uart_port_t uart_num, uint32_t inverse_mask)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_inverse_signal(&(uart_context[uart_num].hal), inverse_mask);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_sw_flow_ctrl(uart_port_t uart_num, bool enable, uint8_t rx_thresh_xon, uint8_t rx_thresh_xoff)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((rx_thresh_xon < SOC_UART_FIFO_LEN), "rx flow xon thresh error", ESP_FAIL);
|
|
UART_CHECK((rx_thresh_xoff < SOC_UART_FIFO_LEN), "rx flow xoff thresh error", ESP_FAIL);
|
|
uart_sw_flowctrl_t sw_flow_ctl = {
|
|
.xon_char = XON,
|
|
.xoff_char = XOFF,
|
|
.xon_thrd = rx_thresh_xon,
|
|
.xoff_thrd = rx_thresh_xoff,
|
|
};
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_sw_flow_ctrl(&(uart_context[uart_num].hal), &sw_flow_ctl, enable);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_hw_flow_ctrl(uart_port_t uart_num, uart_hw_flowcontrol_t flow_ctrl, uint8_t rx_thresh)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((rx_thresh < SOC_UART_FIFO_LEN), "rx flow thresh error", ESP_FAIL);
|
|
UART_CHECK((flow_ctrl < UART_HW_FLOWCTRL_MAX), "hw_flowctrl mode error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_hw_flow_ctrl(&(uart_context[uart_num].hal), flow_ctrl, rx_thresh);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_get_hw_flow_ctrl(uart_port_t uart_num, uart_hw_flowcontrol_t *flow_ctrl)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL)
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_get_hw_flow_ctrl(&(uart_context[uart_num].hal), flow_ctrl);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t UART_ISR_ATTR uart_clear_intr_status(uart_port_t uart_num, uint32_t clr_mask)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), clr_mask);
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_enable_intr_mask(uart_port_t uart_num, uint32_t enable_mask)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
/* Keep track of the interrupt toggling. In fact, without such variable,
|
|
* once the RX buffer is full and the RX interrupts disabled, it is
|
|
* impossible what was the previous state (enabled/disabled) of these
|
|
* interrupt masks. Thus, this will be very particularly handy when
|
|
* emptying a filled RX buffer. */
|
|
p_uart_obj[uart_num]->rx_int_usr_mask |= enable_mask;
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), enable_mask);
|
|
uart_hal_ena_intr_mask(&(uart_context[uart_num].hal), enable_mask);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
/**
|
|
* @brief Function re-enabling the given interrupts (mask) if and only if
|
|
* they have not been disabled by the user.
|
|
*
|
|
* @param uart_num UART number to perform the operation on
|
|
* @param enable_mask Interrupts (flags) to be re-enabled
|
|
*
|
|
* @return ESP_OK in success, ESP_FAIL if uart_num is incorrect
|
|
*/
|
|
static esp_err_t uart_reenable_intr_mask(uart_port_t uart_num, uint32_t enable_mask)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
/* Mask will only contain the interrupt flags that needs to be re-enabled
|
|
* AND which have NOT been explicitly disabled by the user. */
|
|
uint32_t mask = p_uart_obj[uart_num]->rx_int_usr_mask & enable_mask;
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), mask);
|
|
uart_hal_ena_intr_mask(&(uart_context[uart_num].hal), mask);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_disable_intr_mask(uart_port_t uart_num, uint32_t disable_mask)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
p_uart_obj[uart_num]->rx_int_usr_mask &= ~disable_mask;
|
|
uart_hal_disable_intr_mask(&(uart_context[uart_num].hal), disable_mask);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
static esp_err_t uart_pattern_link_free(uart_port_t uart_num)
|
|
{
|
|
int *pdata = NULL;
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
if (p_uart_obj[uart_num]->rx_pattern_pos.data != NULL) {
|
|
pdata = p_uart_obj[uart_num]->rx_pattern_pos.data;
|
|
p_uart_obj[uart_num]->rx_pattern_pos.data = NULL;
|
|
p_uart_obj[uart_num]->rx_pattern_pos.wr = 0;
|
|
p_uart_obj[uart_num]->rx_pattern_pos.rd = 0;
|
|
}
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
free(pdata);
|
|
return ESP_OK;
|
|
}
|
|
|
|
static esp_err_t UART_ISR_ATTR uart_pattern_enqueue(uart_port_t uart_num, int pos)
|
|
{
|
|
esp_err_t ret = ESP_OK;
|
|
uart_pat_rb_t *p_pos = &p_uart_obj[uart_num]->rx_pattern_pos;
|
|
int next = p_pos->wr + 1;
|
|
if (next >= p_pos->len) {
|
|
next = 0;
|
|
}
|
|
if (next == p_pos->rd) {
|
|
#ifndef CONFIG_UART_ISR_IN_IRAM //Only log if ISR is not in IRAM
|
|
ESP_EARLY_LOGW(UART_TAG, "Fail to enqueue pattern position, pattern queue is full.");
|
|
#endif
|
|
ret = ESP_FAIL;
|
|
} else {
|
|
p_pos->data[p_pos->wr] = pos;
|
|
p_pos->wr = next;
|
|
ret = ESP_OK;
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
static esp_err_t uart_pattern_dequeue(uart_port_t uart_num)
|
|
{
|
|
if (p_uart_obj[uart_num]->rx_pattern_pos.data == NULL) {
|
|
return ESP_ERR_INVALID_STATE;
|
|
} else {
|
|
esp_err_t ret = ESP_OK;
|
|
uart_pat_rb_t *p_pos = &p_uart_obj[uart_num]->rx_pattern_pos;
|
|
if (p_pos->rd == p_pos->wr) {
|
|
ret = ESP_FAIL;
|
|
} else {
|
|
p_pos->rd++;
|
|
}
|
|
if (p_pos->rd >= p_pos->len) {
|
|
p_pos->rd = 0;
|
|
}
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
static esp_err_t uart_pattern_queue_update(uart_port_t uart_num, int diff_len)
|
|
{
|
|
uart_pat_rb_t *p_pos = &p_uart_obj[uart_num]->rx_pattern_pos;
|
|
int rd = p_pos->rd;
|
|
while (rd != p_pos->wr) {
|
|
p_pos->data[rd] -= diff_len;
|
|
int rd_rec = rd;
|
|
rd ++;
|
|
if (rd >= p_pos->len) {
|
|
rd = 0;
|
|
}
|
|
if (p_pos->data[rd_rec] < 0) {
|
|
p_pos->rd = rd;
|
|
}
|
|
}
|
|
return ESP_OK;
|
|
}
|
|
|
|
int uart_pattern_pop_pos(uart_port_t uart_num)
|
|
{
|
|
UART_CHECK((p_uart_obj[uart_num]), "uart driver error", (-1));
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_pat_rb_t *pat_pos = &p_uart_obj[uart_num]->rx_pattern_pos;
|
|
int pos = -1;
|
|
if (pat_pos != NULL && pat_pos->rd != pat_pos->wr) {
|
|
pos = pat_pos->data[pat_pos->rd];
|
|
uart_pattern_dequeue(uart_num);
|
|
}
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return pos;
|
|
}
|
|
|
|
int uart_pattern_get_pos(uart_port_t uart_num)
|
|
{
|
|
UART_CHECK((p_uart_obj[uart_num]), "uart driver error", (-1));
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_pat_rb_t *pat_pos = &p_uart_obj[uart_num]->rx_pattern_pos;
|
|
int pos = -1;
|
|
if (pat_pos != NULL && pat_pos->rd != pat_pos->wr) {
|
|
pos = pat_pos->data[pat_pos->rd];
|
|
}
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return pos;
|
|
}
|
|
|
|
esp_err_t uart_pattern_queue_reset(uart_port_t uart_num, int queue_length)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((p_uart_obj[uart_num]), "uart driver error", ESP_ERR_INVALID_STATE);
|
|
|
|
int *pdata = (int *) malloc(queue_length * sizeof(int));
|
|
if (pdata == NULL) {
|
|
return ESP_ERR_NO_MEM;
|
|
}
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
int *ptmp = p_uart_obj[uart_num]->rx_pattern_pos.data;
|
|
p_uart_obj[uart_num]->rx_pattern_pos.data = pdata;
|
|
p_uart_obj[uart_num]->rx_pattern_pos.len = queue_length;
|
|
p_uart_obj[uart_num]->rx_pattern_pos.rd = 0;
|
|
p_uart_obj[uart_num]->rx_pattern_pos.wr = 0;
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
free(ptmp);
|
|
return ESP_OK;
|
|
}
|
|
|
|
#if CONFIG_IDF_TARGET_ESP32
|
|
esp_err_t uart_enable_pattern_det_intr(uart_port_t uart_num, char pattern_chr, uint8_t chr_num, int chr_tout, int post_idle, int pre_idle)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK(chr_tout >= 0 && chr_tout <= UART_RX_GAP_TOUT_V, "uart pattern set error\n", ESP_FAIL);
|
|
UART_CHECK(post_idle >= 0 && post_idle <= UART_POST_IDLE_NUM_V, "uart pattern set error\n", ESP_FAIL);
|
|
UART_CHECK(pre_idle >= 0 && pre_idle <= UART_PRE_IDLE_NUM_V, "uart pattern set error\n", ESP_FAIL);
|
|
uart_at_cmd_t at_cmd = {0};
|
|
at_cmd.cmd_char = pattern_chr;
|
|
at_cmd.char_num = chr_num;
|
|
at_cmd.gap_tout = chr_tout;
|
|
at_cmd.pre_idle = pre_idle;
|
|
at_cmd.post_idle = post_idle;
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_CMD_CHAR_DET);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_at_cmd_char(&(uart_context[uart_num].hal), &at_cmd);
|
|
uart_hal_ena_intr_mask(&(uart_context[uart_num].hal), UART_INTR_CMD_CHAR_DET);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
#endif
|
|
|
|
esp_err_t uart_enable_pattern_det_baud_intr(uart_port_t uart_num, char pattern_chr, uint8_t chr_num, int chr_tout, int post_idle, int pre_idle)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK(chr_tout >= 0 && chr_tout <= UART_RX_GAP_TOUT_V, "uart pattern set error\n", ESP_FAIL);
|
|
UART_CHECK(post_idle >= 0 && post_idle <= UART_POST_IDLE_NUM_V, "uart pattern set error\n", ESP_FAIL);
|
|
UART_CHECK(pre_idle >= 0 && pre_idle <= UART_PRE_IDLE_NUM_V, "uart pattern set error\n", ESP_FAIL);
|
|
uart_at_cmd_t at_cmd = {0};
|
|
at_cmd.cmd_char = pattern_chr;
|
|
at_cmd.char_num = chr_num;
|
|
|
|
#if CONFIG_IDF_TARGET_ESP32
|
|
int apb_clk_freq = 0;
|
|
uint32_t uart_baud = 0;
|
|
uint32_t uart_div = 0;
|
|
uart_get_baudrate(uart_num, &uart_baud);
|
|
apb_clk_freq = esp_clk_apb_freq();
|
|
uart_div = apb_clk_freq / uart_baud;
|
|
|
|
at_cmd.gap_tout = chr_tout * uart_div;
|
|
at_cmd.pre_idle = pre_idle * uart_div;
|
|
at_cmd.post_idle = post_idle * uart_div;
|
|
#elif CONFIG_IDF_TARGET_ESP32S2
|
|
at_cmd.gap_tout = chr_tout;
|
|
at_cmd.pre_idle = pre_idle;
|
|
at_cmd.post_idle = post_idle;
|
|
#endif
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_CMD_CHAR_DET);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_at_cmd_char(&(uart_context[uart_num].hal), &at_cmd);
|
|
uart_hal_ena_intr_mask(&(uart_context[uart_num].hal), UART_INTR_CMD_CHAR_DET);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
|
|
esp_err_t uart_disable_pattern_det_intr(uart_port_t uart_num)
|
|
{
|
|
return uart_disable_intr_mask(uart_num, UART_INTR_CMD_CHAR_DET);
|
|
}
|
|
|
|
esp_err_t uart_enable_rx_intr(uart_port_t uart_num)
|
|
{
|
|
return uart_enable_intr_mask(uart_num, UART_INTR_RXFIFO_FULL | UART_INTR_RXFIFO_TOUT);
|
|
}
|
|
|
|
esp_err_t uart_disable_rx_intr(uart_port_t uart_num)
|
|
{
|
|
return uart_disable_intr_mask(uart_num, UART_INTR_RXFIFO_FULL | UART_INTR_RXFIFO_TOUT);
|
|
}
|
|
|
|
esp_err_t uart_disable_tx_intr(uart_port_t uart_num)
|
|
{
|
|
return uart_disable_intr_mask(uart_num, UART_INTR_TXFIFO_EMPTY);
|
|
}
|
|
|
|
esp_err_t uart_enable_tx_intr(uart_port_t uart_num, int enable, int thresh)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((thresh < SOC_UART_FIFO_LEN), "empty intr threshold error", ESP_FAIL);
|
|
if (enable == 0) {
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_disable_intr_mask(&(uart_context[uart_num].hal), UART_INTR_TXFIFO_EMPTY);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
} else {
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_TXFIFO_EMPTY);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_txfifo_empty_thr(&(uart_context[uart_num].hal), thresh);
|
|
uart_hal_ena_intr_mask(&(uart_context[uart_num].hal), UART_INTR_TXFIFO_EMPTY);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
}
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_isr_register(uart_port_t uart_num, void (*fn)(void *), void *arg, int intr_alloc_flags, uart_isr_handle_t *handle)
|
|
{
|
|
int ret;
|
|
uart_isr_handle_t rethandle;
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
ret = esp_intr_alloc(uart_periph_signal[uart_num].irq, intr_alloc_flags, fn, arg, &rethandle);
|
|
if (ret == ESP_OK) {
|
|
p_uart_obj[uart_num]->intr_handle = rethandle;
|
|
|
|
if (handle != NULL) {
|
|
*handle = rethandle;
|
|
}
|
|
}
|
|
return ret;
|
|
}
|
|
|
|
esp_err_t uart_isr_free(uart_port_t uart_num)
|
|
{
|
|
esp_err_t ret;
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((p_uart_obj[uart_num]), "uart driver error", ESP_FAIL);
|
|
UART_CHECK((p_uart_obj[uart_num]->intr_handle != NULL), "uart driver error", ESP_ERR_INVALID_ARG);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
ret = esp_intr_free(p_uart_obj[uart_num]->intr_handle);
|
|
p_uart_obj[uart_num]->intr_handle = NULL;
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ret;
|
|
}
|
|
|
|
//internal signal can be output to multiple GPIO pads
|
|
//only one GPIO pad can connect with input signal
|
|
esp_err_t uart_set_pin(uart_port_t uart_num, int tx_io_num, int rx_io_num, int rts_io_num, int cts_io_num)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((tx_io_num < 0 || (GPIO_IS_VALID_OUTPUT_GPIO(tx_io_num))), "tx_io_num error", ESP_FAIL);
|
|
UART_CHECK((rx_io_num < 0 || (GPIO_IS_VALID_GPIO(rx_io_num))), "rx_io_num error", ESP_FAIL);
|
|
UART_CHECK((rts_io_num < 0 || (GPIO_IS_VALID_OUTPUT_GPIO(rts_io_num))), "rts_io_num error", ESP_FAIL);
|
|
UART_CHECK((cts_io_num < 0 || (GPIO_IS_VALID_GPIO(cts_io_num))), "cts_io_num error", ESP_FAIL);
|
|
|
|
if(tx_io_num >= 0) {
|
|
gpio_hal_iomux_func_sel(GPIO_PIN_MUX_REG[tx_io_num], PIN_FUNC_GPIO);
|
|
gpio_set_level(tx_io_num, 1);
|
|
esp_rom_gpio_connect_out_signal(tx_io_num, uart_periph_signal[uart_num].tx_sig, 0, 0);
|
|
}
|
|
if(rx_io_num >= 0) {
|
|
gpio_hal_iomux_func_sel(GPIO_PIN_MUX_REG[rx_io_num], PIN_FUNC_GPIO);
|
|
gpio_set_pull_mode(rx_io_num, GPIO_PULLUP_ONLY);
|
|
gpio_set_direction(rx_io_num, GPIO_MODE_INPUT);
|
|
esp_rom_gpio_connect_in_signal(rx_io_num, uart_periph_signal[uart_num].rx_sig, 0);
|
|
}
|
|
if(rts_io_num >= 0) {
|
|
gpio_hal_iomux_func_sel(GPIO_PIN_MUX_REG[rts_io_num], PIN_FUNC_GPIO);
|
|
gpio_set_direction(rts_io_num, GPIO_MODE_OUTPUT);
|
|
esp_rom_gpio_connect_out_signal(rts_io_num, uart_periph_signal[uart_num].rts_sig, 0, 0);
|
|
}
|
|
if(cts_io_num >= 0) {
|
|
gpio_hal_iomux_func_sel(GPIO_PIN_MUX_REG[cts_io_num], PIN_FUNC_GPIO);
|
|
gpio_set_pull_mode(cts_io_num, GPIO_PULLUP_ONLY);
|
|
gpio_set_direction(cts_io_num, GPIO_MODE_INPUT);
|
|
esp_rom_gpio_connect_in_signal(cts_io_num, uart_periph_signal[uart_num].cts_sig, 0);
|
|
}
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_rts(uart_port_t uart_num, int level)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((!uart_hal_is_hw_rts_en(&(uart_context[uart_num].hal))), "disable hw flowctrl before using sw control", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_rts(&(uart_context[uart_num].hal), level);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_dtr(uart_port_t uart_num, int level)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_dtr(&(uart_context[uart_num].hal), level);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_tx_idle_num(uart_port_t uart_num, uint16_t idle_num)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((idle_num <= UART_TX_IDLE_NUM_V), "uart idle num error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_tx_idle_num(&(uart_context[uart_num].hal), idle_num);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_param_config(uart_port_t uart_num, const uart_config_t *uart_config)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((uart_config), "param null", ESP_FAIL);
|
|
UART_CHECK((uart_config->rx_flow_ctrl_thresh < SOC_UART_FIFO_LEN), "rx flow thresh error", ESP_FAIL);
|
|
UART_CHECK((uart_config->flow_ctrl < UART_HW_FLOWCTRL_MAX), "hw_flowctrl mode error", ESP_FAIL);
|
|
UART_CHECK((uart_config->data_bits < UART_DATA_BITS_MAX), "data bit error", ESP_FAIL);
|
|
uart_module_enable(uart_num);
|
|
#if SOC_UART_SUPPORT_RTC_CLK
|
|
if (uart_config->source_clk == UART_SCLK_RTC) {
|
|
rtc_clk_enable(uart_num);
|
|
}
|
|
#endif
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_init(&(uart_context[uart_num].hal), uart_num);
|
|
uart_hal_set_sclk(&(uart_context[uart_num].hal), uart_config->source_clk);
|
|
uart_hal_set_baudrate(&(uart_context[uart_num].hal), uart_config->baud_rate);
|
|
uart_hal_set_parity(&(uart_context[uart_num].hal), uart_config->parity);
|
|
uart_hal_set_data_bit_num(&(uart_context[uart_num].hal), uart_config->data_bits);
|
|
uart_hal_set_stop_bits(&(uart_context[uart_num].hal), uart_config->stop_bits);
|
|
uart_hal_set_tx_idle_num(&(uart_context[uart_num].hal), UART_TX_IDLE_NUM_DEFAULT);
|
|
uart_hal_set_hw_flow_ctrl(&(uart_context[uart_num].hal), uart_config->flow_ctrl, uart_config->rx_flow_ctrl_thresh);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_rxfifo_rst(&(uart_context[uart_num].hal));
|
|
uart_hal_txfifo_rst(&(uart_context[uart_num].hal));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_intr_config(uart_port_t uart_num, const uart_intr_config_t *intr_conf)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((intr_conf), "param null", ESP_FAIL);
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_LL_INTR_MASK);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
if (intr_conf->intr_enable_mask & UART_INTR_RXFIFO_TOUT) {
|
|
uart_hal_set_rx_timeout(&(uart_context[uart_num].hal), intr_conf->rx_timeout_thresh);
|
|
} else {
|
|
//Disable rx_tout intr
|
|
uart_hal_set_rx_timeout(&(uart_context[uart_num].hal), 0);
|
|
}
|
|
if (intr_conf->intr_enable_mask & UART_INTR_RXFIFO_FULL) {
|
|
uart_hal_set_rxfifo_full_thr(&(uart_context[uart_num].hal), intr_conf->rxfifo_full_thresh);
|
|
}
|
|
if (intr_conf->intr_enable_mask & UART_INTR_TXFIFO_EMPTY) {
|
|
uart_hal_set_txfifo_empty_thr(&(uart_context[uart_num].hal), intr_conf->txfifo_empty_intr_thresh);
|
|
}
|
|
uart_hal_ena_intr_mask(&(uart_context[uart_num].hal), intr_conf->intr_enable_mask);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
static int UART_ISR_ATTR uart_find_pattern_from_last(uint8_t *buf, int length, uint8_t pat_chr, uint8_t pat_num)
|
|
{
|
|
int cnt = 0;
|
|
int len = length;
|
|
while (len >= 0) {
|
|
if (buf[len] == pat_chr) {
|
|
cnt++;
|
|
} else {
|
|
cnt = 0;
|
|
}
|
|
if (cnt >= pat_num) {
|
|
break;
|
|
}
|
|
len --;
|
|
}
|
|
return len;
|
|
}
|
|
|
|
static uint32_t UART_ISR_ATTR uart_enable_tx_write_fifo(uart_port_t uart_num, const uint8_t *pbuf, uint32_t len)
|
|
{
|
|
uint32_t sent_len = 0;
|
|
UART_ENTER_CRITICAL_SAFE(&(uart_context[uart_num].spinlock));
|
|
if (UART_IS_MODE_SET(uart_num, UART_MODE_RS485_HALF_DUPLEX)) {
|
|
uart_hal_set_rts(&(uart_context[uart_num].hal), 0);
|
|
uart_hal_ena_intr_mask(&(uart_context[uart_num].hal), UART_INTR_TX_DONE);
|
|
}
|
|
uart_hal_write_txfifo(&(uart_context[uart_num].hal), pbuf, len, &sent_len);
|
|
UART_EXIT_CRITICAL_SAFE(&(uart_context[uart_num].spinlock));
|
|
return sent_len;
|
|
}
|
|
|
|
//internal isr handler for default driver code.
|
|
static void UART_ISR_ATTR uart_rx_intr_handler_default(void *param)
|
|
{
|
|
uart_obj_t *p_uart = (uart_obj_t *) param;
|
|
uint8_t uart_num = p_uart->uart_num;
|
|
int rx_fifo_len = 0;
|
|
uint32_t uart_intr_status = 0;
|
|
uart_event_t uart_event;
|
|
portBASE_TYPE HPTaskAwoken = 0;
|
|
static uint8_t pat_flg = 0;
|
|
while (1) {
|
|
// The `continue statement` may cause the interrupt to loop infinitely
|
|
// we exit the interrupt here
|
|
uart_intr_status = uart_hal_get_intsts_mask(&(uart_context[uart_num].hal));
|
|
//Exit form while loop
|
|
if (uart_intr_status == 0) {
|
|
break;
|
|
}
|
|
uart_event.type = UART_EVENT_MAX;
|
|
if (uart_intr_status & UART_INTR_TXFIFO_EMPTY) {
|
|
UART_ENTER_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_disable_intr_mask(&(uart_context[uart_num].hal), UART_INTR_TXFIFO_EMPTY);
|
|
UART_EXIT_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_TXFIFO_EMPTY);
|
|
if (p_uart->tx_waiting_brk) {
|
|
continue;
|
|
}
|
|
//TX semaphore will only be used when tx_buf_size is zero.
|
|
if (p_uart->tx_waiting_fifo == true && p_uart->tx_buf_size == 0) {
|
|
p_uart->tx_waiting_fifo = false;
|
|
xSemaphoreGiveFromISR(p_uart->tx_fifo_sem, &HPTaskAwoken);
|
|
} else {
|
|
//We don't use TX ring buffer, because the size is zero.
|
|
if (p_uart->tx_buf_size == 0) {
|
|
continue;
|
|
}
|
|
bool en_tx_flg = false;
|
|
uint32_t tx_fifo_rem = uart_hal_get_txfifo_len(&(uart_context[uart_num].hal));
|
|
//We need to put a loop here, in case all the buffer items are very short.
|
|
//That would cause a watch_dog reset because empty interrupt happens so often.
|
|
//Although this is a loop in ISR, this loop will execute at most 128 turns.
|
|
while (tx_fifo_rem) {
|
|
if (p_uart->tx_len_tot == 0 || p_uart->tx_ptr == NULL || p_uart->tx_len_cur == 0) {
|
|
size_t size;
|
|
p_uart->tx_head = (uart_tx_data_t *) xRingbufferReceiveFromISR(p_uart->tx_ring_buf, &size);
|
|
if (p_uart->tx_head) {
|
|
//The first item is the data description
|
|
//Get the first item to get the data information
|
|
if (p_uart->tx_len_tot == 0) {
|
|
p_uart->tx_ptr = NULL;
|
|
p_uart->tx_len_tot = p_uart->tx_head->tx_data.size;
|
|
if (p_uart->tx_head->type == UART_DATA_BREAK) {
|
|
p_uart->tx_brk_flg = 1;
|
|
p_uart->tx_brk_len = p_uart->tx_head->tx_data.brk_len;
|
|
}
|
|
//We have saved the data description from the 1st item, return buffer.
|
|
vRingbufferReturnItemFromISR(p_uart->tx_ring_buf, p_uart->tx_head, &HPTaskAwoken);
|
|
} else if (p_uart->tx_ptr == NULL) {
|
|
//Update the TX item pointer, we will need this to return item to buffer.
|
|
p_uart->tx_ptr = (uint8_t *)p_uart->tx_head;
|
|
en_tx_flg = true;
|
|
p_uart->tx_len_cur = size;
|
|
}
|
|
} else {
|
|
//Can not get data from ring buffer, return;
|
|
break;
|
|
}
|
|
}
|
|
if (p_uart->tx_len_tot > 0 && p_uart->tx_ptr && p_uart->tx_len_cur > 0) {
|
|
// To fill the TX FIFO.
|
|
uint32_t send_len = uart_enable_tx_write_fifo(uart_num, (const uint8_t *) p_uart->tx_ptr,
|
|
MIN(p_uart->tx_len_cur, tx_fifo_rem));
|
|
p_uart->tx_ptr += send_len;
|
|
p_uart->tx_len_tot -= send_len;
|
|
p_uart->tx_len_cur -= send_len;
|
|
tx_fifo_rem -= send_len;
|
|
if (p_uart->tx_len_cur == 0) {
|
|
//Return item to ring buffer.
|
|
vRingbufferReturnItemFromISR(p_uart->tx_ring_buf, p_uart->tx_head, &HPTaskAwoken);
|
|
p_uart->tx_head = NULL;
|
|
p_uart->tx_ptr = NULL;
|
|
//Sending item done, now we need to send break if there is a record.
|
|
//Set TX break signal after FIFO is empty
|
|
if (p_uart->tx_len_tot == 0 && p_uart->tx_brk_flg == 1) {
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_TX_BRK_DONE);
|
|
UART_ENTER_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_tx_break(&(uart_context[uart_num].hal), p_uart->tx_brk_len);
|
|
uart_hal_ena_intr_mask(&(uart_context[uart_num].hal), UART_INTR_TX_BRK_DONE);
|
|
UART_EXIT_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
p_uart->tx_waiting_brk = 1;
|
|
//do not enable TX empty interrupt
|
|
en_tx_flg = false;
|
|
} else {
|
|
//enable TX empty interrupt
|
|
en_tx_flg = true;
|
|
}
|
|
} else {
|
|
//enable TX empty interrupt
|
|
en_tx_flg = true;
|
|
}
|
|
}
|
|
}
|
|
if (en_tx_flg) {
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_TXFIFO_EMPTY);
|
|
UART_ENTER_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_ena_intr_mask(&(uart_context[uart_num].hal), UART_INTR_TXFIFO_EMPTY);
|
|
UART_EXIT_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
}
|
|
}
|
|
} else if ((uart_intr_status & UART_INTR_RXFIFO_TOUT)
|
|
|| (uart_intr_status & UART_INTR_RXFIFO_FULL)
|
|
|| (uart_intr_status & UART_INTR_CMD_CHAR_DET)
|
|
) {
|
|
if (pat_flg == 1) {
|
|
uart_intr_status |= UART_INTR_CMD_CHAR_DET;
|
|
pat_flg = 0;
|
|
}
|
|
if (p_uart->rx_buffer_full_flg == false) {
|
|
rx_fifo_len = uart_hal_get_rxfifo_len(&(uart_context[uart_num].hal));
|
|
if ((p_uart_obj[uart_num]->rx_always_timeout_flg) && !(uart_intr_status & UART_INTR_RXFIFO_TOUT)) {
|
|
rx_fifo_len--; // leave one byte in the fifo in order to trigger uart_intr_rxfifo_tout
|
|
}
|
|
uart_hal_read_rxfifo(&(uart_context[uart_num].hal), p_uart->rx_data_buf, &rx_fifo_len);
|
|
uint8_t pat_chr = 0;
|
|
uint8_t pat_num = 0;
|
|
int pat_idx = -1;
|
|
uart_hal_get_at_cmd_char(&(uart_context[uart_num].hal), &pat_chr, &pat_num);
|
|
|
|
//Get the buffer from the FIFO
|
|
if (uart_intr_status & UART_INTR_CMD_CHAR_DET) {
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_CMD_CHAR_DET);
|
|
uart_event.type = UART_PATTERN_DET;
|
|
uart_event.size = rx_fifo_len;
|
|
pat_idx = uart_find_pattern_from_last(p_uart->rx_data_buf, rx_fifo_len - 1, pat_chr, pat_num);
|
|
} else {
|
|
//After Copying the Data From FIFO ,Clear intr_status
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_RXFIFO_TOUT | UART_INTR_RXFIFO_FULL);
|
|
uart_event.type = UART_DATA;
|
|
uart_event.size = rx_fifo_len;
|
|
uart_event.timeout_flag = (uart_intr_status & UART_INTR_RXFIFO_TOUT) ? true : false;
|
|
UART_ENTER_CRITICAL_ISR(&uart_selectlock);
|
|
if (p_uart->uart_select_notif_callback) {
|
|
p_uart->uart_select_notif_callback(uart_num, UART_SELECT_READ_NOTIF, &HPTaskAwoken);
|
|
}
|
|
UART_EXIT_CRITICAL_ISR(&uart_selectlock);
|
|
}
|
|
p_uart->rx_stash_len = rx_fifo_len;
|
|
//If we fail to push data to ring buffer, we will have to stash the data, and send next time.
|
|
//Mainly for applications that uses flow control or small ring buffer.
|
|
if (pdFALSE == xRingbufferSendFromISR(p_uart->rx_ring_buf, p_uart->rx_data_buf, p_uart->rx_stash_len, &HPTaskAwoken)) {
|
|
p_uart->rx_buffer_full_flg = true;
|
|
UART_ENTER_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_disable_intr_mask(&(uart_context[uart_num].hal), UART_INTR_RXFIFO_TOUT | UART_INTR_RXFIFO_FULL);
|
|
UART_EXIT_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
if (uart_event.type == UART_PATTERN_DET) {
|
|
UART_ENTER_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
if (rx_fifo_len < pat_num) {
|
|
//some of the characters are read out in last interrupt
|
|
uart_pattern_enqueue(uart_num, p_uart->rx_buffered_len - (pat_num - rx_fifo_len));
|
|
} else {
|
|
uart_pattern_enqueue(uart_num,
|
|
pat_idx <= -1 ?
|
|
//can not find the pattern in buffer,
|
|
p_uart->rx_buffered_len + p_uart->rx_stash_len :
|
|
// find the pattern in buffer
|
|
p_uart->rx_buffered_len + pat_idx);
|
|
}
|
|
UART_EXIT_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
if ((p_uart->event_queue != NULL) && (pdFALSE == xQueueSendFromISR(p_uart->event_queue, (void * )&uart_event, &HPTaskAwoken))) {
|
|
#ifndef CONFIG_UART_ISR_IN_IRAM //Only log if ISR is not in IRAM
|
|
ESP_EARLY_LOGV(UART_TAG, "UART event queue full");
|
|
#endif
|
|
}
|
|
}
|
|
uart_event.type = UART_BUFFER_FULL;
|
|
} else {
|
|
UART_ENTER_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
if (uart_intr_status & UART_INTR_CMD_CHAR_DET) {
|
|
if (rx_fifo_len < pat_num) {
|
|
//some of the characters are read out in last interrupt
|
|
uart_pattern_enqueue(uart_num, p_uart->rx_buffered_len - (pat_num - rx_fifo_len));
|
|
} else if (pat_idx >= 0) {
|
|
// find the pattern in stash buffer.
|
|
uart_pattern_enqueue(uart_num, p_uart->rx_buffered_len + pat_idx);
|
|
}
|
|
}
|
|
p_uart->rx_buffered_len += p_uart->rx_stash_len;
|
|
UART_EXIT_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
}
|
|
} else {
|
|
UART_ENTER_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_disable_intr_mask(&(uart_context[uart_num].hal), UART_INTR_RXFIFO_FULL | UART_INTR_RXFIFO_TOUT);
|
|
UART_EXIT_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_RXFIFO_FULL | UART_INTR_RXFIFO_TOUT);
|
|
if (uart_intr_status & UART_INTR_CMD_CHAR_DET) {
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_CMD_CHAR_DET);
|
|
uart_event.type = UART_PATTERN_DET;
|
|
uart_event.size = rx_fifo_len;
|
|
pat_flg = 1;
|
|
}
|
|
}
|
|
} else if (uart_intr_status & UART_INTR_RXFIFO_OVF) {
|
|
// When fifo overflows, we reset the fifo.
|
|
UART_ENTER_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_rxfifo_rst(&(uart_context[uart_num].hal));
|
|
UART_EXIT_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
UART_ENTER_CRITICAL_ISR(&uart_selectlock);
|
|
if (p_uart->uart_select_notif_callback) {
|
|
p_uart->uart_select_notif_callback(uart_num, UART_SELECT_ERROR_NOTIF, &HPTaskAwoken);
|
|
}
|
|
UART_EXIT_CRITICAL_ISR(&uart_selectlock);
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_RXFIFO_OVF);
|
|
uart_event.type = UART_FIFO_OVF;
|
|
} else if (uart_intr_status & UART_INTR_BRK_DET) {
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_BRK_DET);
|
|
uart_event.type = UART_BREAK;
|
|
} else if (uart_intr_status & UART_INTR_FRAM_ERR) {
|
|
UART_ENTER_CRITICAL_ISR(&uart_selectlock);
|
|
if (p_uart->uart_select_notif_callback) {
|
|
p_uart->uart_select_notif_callback(uart_num, UART_SELECT_ERROR_NOTIF, &HPTaskAwoken);
|
|
}
|
|
UART_EXIT_CRITICAL_ISR(&uart_selectlock);
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_FRAM_ERR);
|
|
uart_event.type = UART_FRAME_ERR;
|
|
} else if (uart_intr_status & UART_INTR_PARITY_ERR) {
|
|
UART_ENTER_CRITICAL_ISR(&uart_selectlock);
|
|
if (p_uart->uart_select_notif_callback) {
|
|
p_uart->uart_select_notif_callback(uart_num, UART_SELECT_ERROR_NOTIF, &HPTaskAwoken);
|
|
}
|
|
UART_EXIT_CRITICAL_ISR(&uart_selectlock);
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_PARITY_ERR);
|
|
uart_event.type = UART_PARITY_ERR;
|
|
} else if (uart_intr_status & UART_INTR_TX_BRK_DONE) {
|
|
UART_ENTER_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_tx_break(&(uart_context[uart_num].hal), 0);
|
|
uart_hal_disable_intr_mask(&(uart_context[uart_num].hal), UART_INTR_TX_BRK_DONE);
|
|
if (p_uart->tx_brk_flg == 1) {
|
|
uart_hal_ena_intr_mask(&(uart_context[uart_num].hal), UART_INTR_TXFIFO_EMPTY);
|
|
}
|
|
UART_EXIT_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_TX_BRK_DONE);
|
|
if (p_uart->tx_brk_flg == 1) {
|
|
p_uart->tx_brk_flg = 0;
|
|
p_uart->tx_waiting_brk = 0;
|
|
} else {
|
|
xSemaphoreGiveFromISR(p_uart->tx_brk_sem, &HPTaskAwoken);
|
|
}
|
|
} else if (uart_intr_status & UART_INTR_TX_BRK_IDLE) {
|
|
UART_ENTER_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_disable_intr_mask(&(uart_context[uart_num].hal), UART_INTR_TX_BRK_IDLE);
|
|
UART_EXIT_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_TX_BRK_IDLE);
|
|
} else if (uart_intr_status & UART_INTR_CMD_CHAR_DET) {
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_CMD_CHAR_DET);
|
|
uart_event.type = UART_PATTERN_DET;
|
|
} else if ((uart_intr_status & UART_INTR_RS485_PARITY_ERR)
|
|
|| (uart_intr_status & UART_INTR_RS485_FRM_ERR)
|
|
|| (uart_intr_status & UART_INTR_RS485_CLASH)) {
|
|
// RS485 collision or frame error interrupt triggered
|
|
UART_ENTER_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_rxfifo_rst(&(uart_context[uart_num].hal));
|
|
// Set collision detection flag
|
|
p_uart_obj[uart_num]->coll_det_flg = true;
|
|
UART_EXIT_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_RS485_CLASH | UART_INTR_RS485_FRM_ERR | UART_INTR_RS485_PARITY_ERR);
|
|
uart_event.type = UART_EVENT_MAX;
|
|
} else if (uart_intr_status & UART_INTR_TX_DONE) {
|
|
if (UART_IS_MODE_SET(uart_num, UART_MODE_RS485_HALF_DUPLEX) && uart_hal_is_tx_idle(&(uart_context[uart_num].hal)) != true) {
|
|
// The TX_DONE interrupt is triggered but transmit is active
|
|
// then postpone interrupt processing for next interrupt
|
|
uart_event.type = UART_EVENT_MAX;
|
|
} else {
|
|
// Workaround for RS485: If the RS485 half duplex mode is active
|
|
// and transmitter is in idle state then reset received buffer and reset RTS pin
|
|
// skip this behavior for other UART modes
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_TX_DONE);
|
|
UART_ENTER_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
uart_hal_disable_intr_mask(&(uart_context[uart_num].hal), UART_INTR_TX_DONE);
|
|
if (UART_IS_MODE_SET(uart_num, UART_MODE_RS485_HALF_DUPLEX)) {
|
|
uart_hal_rxfifo_rst(&(uart_context[uart_num].hal));
|
|
uart_hal_set_rts(&(uart_context[uart_num].hal), 1);
|
|
}
|
|
UART_EXIT_CRITICAL_ISR(&(uart_context[uart_num].spinlock));
|
|
xSemaphoreGiveFromISR(p_uart_obj[uart_num]->tx_done_sem, &HPTaskAwoken);
|
|
}
|
|
} else {
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), uart_intr_status); /*simply clear all other intr status*/
|
|
uart_event.type = UART_EVENT_MAX;
|
|
}
|
|
|
|
if (uart_event.type != UART_EVENT_MAX && p_uart->event_queue) {
|
|
if (pdFALSE == xQueueSendFromISR(p_uart->event_queue, (void * )&uart_event, &HPTaskAwoken)) {
|
|
#ifndef CONFIG_UART_ISR_IN_IRAM //Only log if ISR is not in IRAM
|
|
ESP_EARLY_LOGV(UART_TAG, "UART event queue full");
|
|
#endif
|
|
}
|
|
}
|
|
}
|
|
if (HPTaskAwoken == pdTRUE) {
|
|
portYIELD_FROM_ISR();
|
|
}
|
|
}
|
|
|
|
/**************************************************************/
|
|
esp_err_t uart_wait_tx_done(uart_port_t uart_num, TickType_t ticks_to_wait)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((p_uart_obj[uart_num]), "uart driver error", ESP_FAIL);
|
|
BaseType_t res;
|
|
portTickType ticks_start = xTaskGetTickCount();
|
|
//Take tx_mux
|
|
res = xSemaphoreTake(p_uart_obj[uart_num]->tx_mux, (portTickType)ticks_to_wait);
|
|
if (res == pdFALSE) {
|
|
return ESP_ERR_TIMEOUT;
|
|
}
|
|
xSemaphoreTake(p_uart_obj[uart_num]->tx_done_sem, 0);
|
|
if (uart_hal_is_tx_idle(&(uart_context[uart_num].hal))) {
|
|
xSemaphoreGive(p_uart_obj[uart_num]->tx_mux);
|
|
return ESP_OK;
|
|
}
|
|
if (!UART_IS_MODE_SET(uart_num, UART_MODE_RS485_HALF_DUPLEX)) {
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_TX_DONE);
|
|
}
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_ena_intr_mask(&(uart_context[uart_num].hal), UART_INTR_TX_DONE);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
|
|
TickType_t ticks_end = xTaskGetTickCount();
|
|
if (ticks_end - ticks_start > ticks_to_wait) {
|
|
ticks_to_wait = 0;
|
|
} else {
|
|
ticks_to_wait = ticks_to_wait - (ticks_end - ticks_start);
|
|
}
|
|
//take 2nd tx_done_sem, wait given from ISR
|
|
res = xSemaphoreTake(p_uart_obj[uart_num]->tx_done_sem, (portTickType)ticks_to_wait);
|
|
if (res == pdFALSE) {
|
|
// The TX_DONE interrupt will be disabled in ISR
|
|
xSemaphoreGive(p_uart_obj[uart_num]->tx_mux);
|
|
return ESP_ERR_TIMEOUT;
|
|
}
|
|
xSemaphoreGive(p_uart_obj[uart_num]->tx_mux);
|
|
return ESP_OK;
|
|
}
|
|
|
|
int uart_tx_chars(uart_port_t uart_num, const char *buffer, uint32_t len)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", (-1));
|
|
UART_CHECK((p_uart_obj[uart_num]), "uart driver error", (-1));
|
|
UART_CHECK(buffer, "buffer null", (-1));
|
|
if (len == 0) {
|
|
return 0;
|
|
}
|
|
int tx_len = 0;
|
|
xSemaphoreTake(p_uart_obj[uart_num]->tx_mux, (portTickType)portMAX_DELAY);
|
|
tx_len = (int)uart_enable_tx_write_fifo(uart_num, (const uint8_t *) buffer, len);
|
|
xSemaphoreGive(p_uart_obj[uart_num]->tx_mux);
|
|
return tx_len;
|
|
}
|
|
|
|
static int uart_tx_all(uart_port_t uart_num, const char *src, size_t size, bool brk_en, int brk_len)
|
|
{
|
|
if (size == 0) {
|
|
return 0;
|
|
}
|
|
size_t original_size = size;
|
|
|
|
//lock for uart_tx
|
|
xSemaphoreTake(p_uart_obj[uart_num]->tx_mux, (portTickType)portMAX_DELAY);
|
|
p_uart_obj[uart_num]->coll_det_flg = false;
|
|
if (p_uart_obj[uart_num]->tx_buf_size > 0) {
|
|
size_t max_size = xRingbufferGetMaxItemSize(p_uart_obj[uart_num]->tx_ring_buf);
|
|
int offset = 0;
|
|
uart_tx_data_t evt;
|
|
evt.tx_data.size = size;
|
|
evt.tx_data.brk_len = brk_len;
|
|
if (brk_en) {
|
|
evt.type = UART_DATA_BREAK;
|
|
} else {
|
|
evt.type = UART_DATA;
|
|
}
|
|
xRingbufferSend(p_uart_obj[uart_num]->tx_ring_buf, (void *) &evt, sizeof(uart_tx_data_t), portMAX_DELAY);
|
|
while (size > 0) {
|
|
size_t send_size = size > max_size / 2 ? max_size / 2 : size;
|
|
xRingbufferSend(p_uart_obj[uart_num]->tx_ring_buf, (void *) (src + offset), send_size, portMAX_DELAY);
|
|
size -= send_size;
|
|
offset += send_size;
|
|
uart_enable_tx_intr(uart_num, 1, UART_EMPTY_THRESH_DEFAULT);
|
|
}
|
|
} else {
|
|
while (size) {
|
|
//semaphore for tx_fifo available
|
|
if (pdTRUE == xSemaphoreTake(p_uart_obj[uart_num]->tx_fifo_sem, (portTickType)portMAX_DELAY)) {
|
|
uint32_t sent = uart_enable_tx_write_fifo(uart_num, (const uint8_t *) src, size);
|
|
if (sent < size) {
|
|
p_uart_obj[uart_num]->tx_waiting_fifo = true;
|
|
uart_enable_tx_intr(uart_num, 1, UART_EMPTY_THRESH_DEFAULT);
|
|
}
|
|
size -= sent;
|
|
src += sent;
|
|
}
|
|
}
|
|
if (brk_en) {
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_INTR_TX_BRK_DONE);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_tx_break(&(uart_context[uart_num].hal), brk_len);
|
|
uart_hal_ena_intr_mask(&(uart_context[uart_num].hal), UART_INTR_TX_BRK_DONE);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
xSemaphoreTake(p_uart_obj[uart_num]->tx_brk_sem, (portTickType)portMAX_DELAY);
|
|
}
|
|
xSemaphoreGive(p_uart_obj[uart_num]->tx_fifo_sem);
|
|
}
|
|
xSemaphoreGive(p_uart_obj[uart_num]->tx_mux);
|
|
return original_size;
|
|
}
|
|
|
|
int uart_write_bytes(uart_port_t uart_num, const void *src, size_t size)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", (-1));
|
|
UART_CHECK((p_uart_obj[uart_num] != NULL), "uart driver error", (-1));
|
|
UART_CHECK(src, "buffer null", (-1));
|
|
return uart_tx_all(uart_num, src, size, 0, 0);
|
|
}
|
|
|
|
int uart_write_bytes_with_break(uart_port_t uart_num, const void *src, size_t size, int brk_len)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", (-1));
|
|
UART_CHECK((p_uart_obj[uart_num]), "uart driver error", (-1));
|
|
UART_CHECK((size > 0), "uart size error", (-1));
|
|
UART_CHECK((src), "uart data null", (-1));
|
|
UART_CHECK((brk_len > 0 && brk_len < 256), "break_num error", (-1));
|
|
return uart_tx_all(uart_num, src, size, 1, brk_len);
|
|
}
|
|
|
|
static bool uart_check_buf_full(uart_port_t uart_num)
|
|
{
|
|
if (p_uart_obj[uart_num]->rx_buffer_full_flg) {
|
|
BaseType_t res = xRingbufferSend(p_uart_obj[uart_num]->rx_ring_buf, p_uart_obj[uart_num]->rx_data_buf, p_uart_obj[uart_num]->rx_stash_len, 1);
|
|
if (res == pdTRUE) {
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
p_uart_obj[uart_num]->rx_buffered_len += p_uart_obj[uart_num]->rx_stash_len;
|
|
p_uart_obj[uart_num]->rx_buffer_full_flg = false;
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
/* Only re-activate UART_INTR_RXFIFO_TOUT or UART_INTR_RXFIFO_FULL
|
|
* interrupts if they were NOT explicitly disabled by the user. */
|
|
uart_reenable_intr_mask(p_uart_obj[uart_num]->uart_num, UART_INTR_RXFIFO_TOUT | UART_INTR_RXFIFO_FULL);
|
|
return true;
|
|
}
|
|
}
|
|
return false;
|
|
}
|
|
|
|
int uart_read_bytes(uart_port_t uart_num, void *buf, uint32_t length, TickType_t ticks_to_wait)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", (-1));
|
|
UART_CHECK((buf), "uart data null", (-1));
|
|
UART_CHECK((p_uart_obj[uart_num]), "uart driver error", (-1));
|
|
uint8_t *data = NULL;
|
|
size_t size;
|
|
size_t copy_len = 0;
|
|
int len_tmp;
|
|
if (xSemaphoreTake(p_uart_obj[uart_num]->rx_mux, (portTickType)ticks_to_wait) != pdTRUE) {
|
|
return -1;
|
|
}
|
|
while (length) {
|
|
if (p_uart_obj[uart_num]->rx_cur_remain == 0) {
|
|
data = (uint8_t *) xRingbufferReceive(p_uart_obj[uart_num]->rx_ring_buf, &size, (portTickType) ticks_to_wait);
|
|
if (data) {
|
|
p_uart_obj[uart_num]->rx_head_ptr = data;
|
|
p_uart_obj[uart_num]->rx_ptr = data;
|
|
p_uart_obj[uart_num]->rx_cur_remain = size;
|
|
} else {
|
|
//When using dual cores, `rx_buffer_full_flg` may read and write on different cores at same time,
|
|
//which may lose synchronization. So we also need to call `uart_check_buf_full` once when ringbuffer is empty
|
|
//to solve the possible asynchronous issues.
|
|
if (uart_check_buf_full(uart_num)) {
|
|
//This condition will never be true if `uart_read_bytes`
|
|
//and `uart_rx_intr_handler_default` are scheduled on the same core.
|
|
continue;
|
|
} else {
|
|
xSemaphoreGive(p_uart_obj[uart_num]->rx_mux);
|
|
return copy_len;
|
|
}
|
|
}
|
|
}
|
|
if (p_uart_obj[uart_num]->rx_cur_remain > length) {
|
|
len_tmp = length;
|
|
} else {
|
|
len_tmp = p_uart_obj[uart_num]->rx_cur_remain;
|
|
}
|
|
memcpy((uint8_t *)buf + copy_len, p_uart_obj[uart_num]->rx_ptr, len_tmp);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
p_uart_obj[uart_num]->rx_buffered_len -= len_tmp;
|
|
uart_pattern_queue_update(uart_num, len_tmp);
|
|
p_uart_obj[uart_num]->rx_ptr += len_tmp;
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
p_uart_obj[uart_num]->rx_cur_remain -= len_tmp;
|
|
copy_len += len_tmp;
|
|
length -= len_tmp;
|
|
if (p_uart_obj[uart_num]->rx_cur_remain == 0) {
|
|
vRingbufferReturnItem(p_uart_obj[uart_num]->rx_ring_buf, p_uart_obj[uart_num]->rx_head_ptr);
|
|
p_uart_obj[uart_num]->rx_head_ptr = NULL;
|
|
p_uart_obj[uart_num]->rx_ptr = NULL;
|
|
uart_check_buf_full(uart_num);
|
|
}
|
|
}
|
|
|
|
xSemaphoreGive(p_uart_obj[uart_num]->rx_mux);
|
|
return copy_len;
|
|
}
|
|
|
|
esp_err_t uart_get_buffered_data_len(uart_port_t uart_num, size_t *size)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((p_uart_obj[uart_num]), "uart driver error", ESP_FAIL);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
*size = p_uart_obj[uart_num]->rx_buffered_len;
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_flush(uart_port_t uart_num) __attribute__((alias("uart_flush_input")));
|
|
|
|
esp_err_t uart_flush_input(uart_port_t uart_num)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((p_uart_obj[uart_num]), "uart driver error", ESP_FAIL);
|
|
uart_obj_t *p_uart = p_uart_obj[uart_num];
|
|
uint8_t *data;
|
|
size_t size;
|
|
|
|
//rx sem protect the ring buffer read related functions
|
|
xSemaphoreTake(p_uart->rx_mux, (portTickType)portMAX_DELAY);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_disable_intr_mask(&(uart_context[uart_num].hal), UART_INTR_RXFIFO_FULL | UART_INTR_RXFIFO_TOUT);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
while (true) {
|
|
if (p_uart->rx_head_ptr) {
|
|
vRingbufferReturnItem(p_uart->rx_ring_buf, p_uart->rx_head_ptr);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
p_uart_obj[uart_num]->rx_buffered_len -= p_uart->rx_cur_remain;
|
|
uart_pattern_queue_update(uart_num, p_uart->rx_cur_remain);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
p_uart->rx_ptr = NULL;
|
|
p_uart->rx_cur_remain = 0;
|
|
p_uart->rx_head_ptr = NULL;
|
|
}
|
|
data = (uint8_t*) xRingbufferReceive(p_uart->rx_ring_buf, &size, (portTickType) 0);
|
|
if (data == NULL) {
|
|
bool error = false;
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
if ( p_uart_obj[uart_num]->rx_buffered_len != 0 ) {
|
|
p_uart_obj[uart_num]->rx_buffered_len = 0;
|
|
error = true;
|
|
}
|
|
//We also need to clear the `rx_buffer_full_flg` here.
|
|
p_uart_obj[uart_num]->rx_buffer_full_flg = false;
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
if (error) {
|
|
// this must be called outside the critical section
|
|
ESP_LOGE(UART_TAG, "rx_buffered_len error");
|
|
}
|
|
break;
|
|
}
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
p_uart_obj[uart_num]->rx_buffered_len -= size;
|
|
uart_pattern_queue_update(uart_num, size);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
vRingbufferReturnItem(p_uart->rx_ring_buf, data);
|
|
if (p_uart_obj[uart_num]->rx_buffer_full_flg) {
|
|
BaseType_t res = xRingbufferSend(p_uart_obj[uart_num]->rx_ring_buf, p_uart_obj[uart_num]->rx_data_buf, p_uart_obj[uart_num]->rx_stash_len, 1);
|
|
if (res == pdTRUE) {
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
p_uart_obj[uart_num]->rx_buffered_len += p_uart_obj[uart_num]->rx_stash_len;
|
|
p_uart_obj[uart_num]->rx_buffer_full_flg = false;
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
}
|
|
}
|
|
}
|
|
p_uart->rx_ptr = NULL;
|
|
p_uart->rx_cur_remain = 0;
|
|
p_uart->rx_head_ptr = NULL;
|
|
uart_hal_rxfifo_rst(&(uart_context[uart_num].hal));
|
|
/* Only re-enable UART_INTR_RXFIFO_TOUT or UART_INTR_RXFIFO_FULL if they
|
|
* were explicitly enabled by the user. */
|
|
uart_reenable_intr_mask(uart_num, UART_INTR_RXFIFO_TOUT | UART_INTR_RXFIFO_FULL);
|
|
xSemaphoreGive(p_uart->rx_mux);
|
|
return ESP_OK;
|
|
}
|
|
|
|
static void uart_free_driver_obj(uart_obj_t *uart_obj)
|
|
{
|
|
if (uart_obj->tx_fifo_sem) {
|
|
vSemaphoreDelete(uart_obj->tx_fifo_sem);
|
|
}
|
|
if (uart_obj->tx_done_sem) {
|
|
vSemaphoreDelete(uart_obj->tx_done_sem);
|
|
}
|
|
if (uart_obj->tx_brk_sem) {
|
|
vSemaphoreDelete(uart_obj->tx_brk_sem);
|
|
}
|
|
if (uart_obj->tx_mux) {
|
|
vSemaphoreDelete(uart_obj->tx_mux);
|
|
}
|
|
if (uart_obj->rx_mux) {
|
|
vSemaphoreDelete(uart_obj->rx_mux);
|
|
}
|
|
if (uart_obj->event_queue) {
|
|
vQueueDelete(uart_obj->event_queue);
|
|
}
|
|
if (uart_obj->rx_ring_buf) {
|
|
vRingbufferDelete(uart_obj->rx_ring_buf);
|
|
}
|
|
if (uart_obj->tx_ring_buf) {
|
|
vRingbufferDelete(uart_obj->tx_ring_buf);
|
|
}
|
|
#if CONFIG_UART_ISR_IN_IRAM
|
|
free(uart_obj->event_queue_storage);
|
|
free(uart_obj->event_queue_struct);
|
|
free(uart_obj->tx_ring_buf_storage);
|
|
free(uart_obj->tx_ring_buf_struct);
|
|
free(uart_obj->rx_ring_buf_storage);
|
|
free(uart_obj->rx_ring_buf_struct);
|
|
free(uart_obj->rx_mux_struct);
|
|
free(uart_obj->tx_mux_struct);
|
|
free(uart_obj->tx_brk_sem_struct);
|
|
free(uart_obj->tx_done_sem_struct);
|
|
free(uart_obj->tx_fifo_sem_struct);
|
|
#endif
|
|
free(uart_obj);
|
|
}
|
|
|
|
static uart_obj_t *uart_alloc_driver_obj(int event_queue_size, int tx_buffer_size, int rx_buffer_size)
|
|
{
|
|
uart_obj_t *uart_obj = heap_caps_calloc(1, sizeof(uart_obj_t), UART_MALLOC_CAPS);
|
|
if (!uart_obj) {
|
|
return NULL;
|
|
}
|
|
#if CONFIG_UART_ISR_IN_IRAM
|
|
if (event_queue_size > 0) {
|
|
uart_obj->event_queue_storage = heap_caps_calloc(event_queue_size, sizeof(uart_event_t), UART_MALLOC_CAPS);
|
|
uart_obj->event_queue_struct = heap_caps_calloc(1, sizeof(StaticQueue_t), UART_MALLOC_CAPS);
|
|
if (!uart_obj->event_queue_storage || !uart_obj->event_queue_struct) {
|
|
goto err;
|
|
}
|
|
}
|
|
if (tx_buffer_size > 0) {
|
|
uart_obj->tx_ring_buf_storage = heap_caps_calloc(1, tx_buffer_size, UART_MALLOC_CAPS);
|
|
uart_obj->tx_ring_buf_struct = heap_caps_calloc(1, sizeof(StaticRingbuffer_t), UART_MALLOC_CAPS);
|
|
if (!uart_obj->tx_ring_buf_storage || !uart_obj->tx_ring_buf_struct) {
|
|
goto err;
|
|
}
|
|
}
|
|
uart_obj->rx_ring_buf_storage = heap_caps_calloc(1, rx_buffer_size, UART_MALLOC_CAPS);
|
|
uart_obj->rx_ring_buf_struct = heap_caps_calloc(1, sizeof(StaticRingbuffer_t), UART_MALLOC_CAPS);
|
|
uart_obj->rx_mux_struct = heap_caps_calloc(1, sizeof(StaticSemaphore_t), UART_MALLOC_CAPS);
|
|
uart_obj->tx_mux_struct = heap_caps_calloc(1, sizeof(StaticSemaphore_t), UART_MALLOC_CAPS);
|
|
uart_obj->tx_brk_sem_struct = heap_caps_calloc(1, sizeof(StaticSemaphore_t), UART_MALLOC_CAPS);
|
|
uart_obj->tx_done_sem_struct = heap_caps_calloc(1, sizeof(StaticSemaphore_t), UART_MALLOC_CAPS);
|
|
uart_obj->tx_fifo_sem_struct = heap_caps_calloc(1, sizeof(StaticSemaphore_t), UART_MALLOC_CAPS);
|
|
if (!uart_obj->rx_ring_buf_storage || !uart_obj->rx_ring_buf_struct || !uart_obj->rx_mux_struct ||
|
|
!uart_obj->tx_mux_struct || !uart_obj->tx_brk_sem_struct || !uart_obj->tx_done_sem_struct ||
|
|
!uart_obj->tx_fifo_sem_struct) {
|
|
goto err;
|
|
}
|
|
if (event_queue_size > 0) {
|
|
uart_obj->event_queue = xQueueCreateStatic(event_queue_size, sizeof(uart_event_t),
|
|
uart_obj->event_queue_storage, uart_obj->event_queue_struct);
|
|
if (!uart_obj->event_queue) {
|
|
goto err;
|
|
}
|
|
}
|
|
if (tx_buffer_size > 0) {
|
|
uart_obj->tx_ring_buf = xRingbufferCreateStatic(tx_buffer_size, RINGBUF_TYPE_NOSPLIT,
|
|
uart_obj->tx_ring_buf_storage, uart_obj->tx_ring_buf_struct);
|
|
if (!uart_obj->tx_ring_buf) {
|
|
goto err;
|
|
}
|
|
}
|
|
uart_obj->rx_ring_buf = xRingbufferCreateStatic(rx_buffer_size, RINGBUF_TYPE_BYTEBUF,
|
|
uart_obj->rx_ring_buf_storage, uart_obj->rx_ring_buf_struct);
|
|
uart_obj->rx_mux = xSemaphoreCreateMutexStatic(uart_obj->rx_mux_struct);
|
|
uart_obj->tx_mux = xSemaphoreCreateMutexStatic(uart_obj->tx_mux_struct);
|
|
uart_obj->tx_brk_sem = xSemaphoreCreateBinaryStatic(uart_obj->tx_brk_sem_struct);
|
|
uart_obj->tx_done_sem = xSemaphoreCreateBinaryStatic(uart_obj->tx_done_sem_struct);
|
|
uart_obj->tx_fifo_sem = xSemaphoreCreateBinaryStatic(uart_obj->tx_fifo_sem_struct);
|
|
if (!uart_obj->rx_ring_buf || !uart_obj->rx_mux || !uart_obj->tx_mux || !uart_obj->tx_brk_sem ||
|
|
!uart_obj->tx_done_sem || !uart_obj->tx_fifo_sem) {
|
|
goto err;
|
|
}
|
|
#else
|
|
if (event_queue_size > 0) {
|
|
uart_obj->event_queue = xQueueCreate(event_queue_size, sizeof(uart_event_t));
|
|
if (!uart_obj->event_queue) {
|
|
goto err;
|
|
}
|
|
}
|
|
if (tx_buffer_size > 0) {
|
|
uart_obj->tx_ring_buf = xRingbufferCreate(tx_buffer_size, RINGBUF_TYPE_NOSPLIT);
|
|
if (!uart_obj->tx_ring_buf) {
|
|
goto err;
|
|
}
|
|
}
|
|
uart_obj->rx_ring_buf = xRingbufferCreate(rx_buffer_size, RINGBUF_TYPE_BYTEBUF);
|
|
uart_obj->tx_mux = xSemaphoreCreateMutex();
|
|
uart_obj->rx_mux = xSemaphoreCreateMutex();
|
|
uart_obj->tx_brk_sem = xSemaphoreCreateBinary();
|
|
uart_obj->tx_done_sem = xSemaphoreCreateBinary();
|
|
uart_obj->tx_fifo_sem = xSemaphoreCreateBinary();
|
|
if (!uart_obj->rx_ring_buf || !uart_obj->rx_mux || !uart_obj->tx_mux || !uart_obj->tx_brk_sem ||
|
|
!uart_obj->tx_done_sem || !uart_obj->tx_fifo_sem) {
|
|
goto err;
|
|
}
|
|
#endif
|
|
return uart_obj;
|
|
|
|
err:
|
|
uart_free_driver_obj(uart_obj);
|
|
return NULL;
|
|
}
|
|
|
|
esp_err_t uart_driver_install(uart_port_t uart_num, int rx_buffer_size, int tx_buffer_size, int event_queue_size, QueueHandle_t *uart_queue, int intr_alloc_flags)
|
|
{
|
|
esp_err_t r;
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
UART_CHECK((rx_buffer_size > SOC_UART_FIFO_LEN), "uart rx buffer length error", ESP_FAIL);
|
|
UART_CHECK((tx_buffer_size > SOC_UART_FIFO_LEN) || (tx_buffer_size == 0), "uart tx buffer length error", ESP_FAIL);
|
|
#if CONFIG_UART_ISR_IN_IRAM
|
|
if ((intr_alloc_flags & ESP_INTR_FLAG_IRAM) == 0) {
|
|
ESP_LOGI(UART_TAG, "ESP_INTR_FLAG_IRAM flag not set while CONFIG_UART_ISR_IN_IRAM is enabled, flag updated");
|
|
intr_alloc_flags |= ESP_INTR_FLAG_IRAM;
|
|
}
|
|
#else
|
|
if ((intr_alloc_flags & ESP_INTR_FLAG_IRAM) != 0) {
|
|
ESP_LOGW(UART_TAG, "ESP_INTR_FLAG_IRAM flag is set while CONFIG_UART_ISR_IN_IRAM is not enabled, flag updated");
|
|
intr_alloc_flags &= ~ESP_INTR_FLAG_IRAM;
|
|
}
|
|
#endif
|
|
|
|
if (p_uart_obj[uart_num] == NULL) {
|
|
p_uart_obj[uart_num] = uart_alloc_driver_obj(event_queue_size, tx_buffer_size, rx_buffer_size);
|
|
if (p_uart_obj[uart_num] == NULL) {
|
|
ESP_LOGE(UART_TAG, "UART driver malloc error");
|
|
return ESP_FAIL;
|
|
}
|
|
p_uart_obj[uart_num]->uart_num = uart_num;
|
|
p_uart_obj[uart_num]->uart_mode = UART_MODE_UART;
|
|
p_uart_obj[uart_num]->coll_det_flg = false;
|
|
p_uart_obj[uart_num]->rx_always_timeout_flg = false;
|
|
p_uart_obj[uart_num]->event_queue_size = event_queue_size;
|
|
p_uart_obj[uart_num]->tx_ptr = NULL;
|
|
p_uart_obj[uart_num]->tx_head = NULL;
|
|
p_uart_obj[uart_num]->tx_len_tot = 0;
|
|
p_uart_obj[uart_num]->tx_brk_flg = 0;
|
|
p_uart_obj[uart_num]->tx_brk_len = 0;
|
|
p_uart_obj[uart_num]->tx_waiting_brk = 0;
|
|
p_uart_obj[uart_num]->rx_buffered_len = 0;
|
|
p_uart_obj[uart_num]->rx_buffer_full_flg = false;
|
|
p_uart_obj[uart_num]->tx_waiting_fifo = false;
|
|
p_uart_obj[uart_num]->rx_ptr = NULL;
|
|
p_uart_obj[uart_num]->rx_cur_remain = 0;
|
|
p_uart_obj[uart_num]->rx_int_usr_mask = UART_INTR_RXFIFO_FULL | UART_INTR_RXFIFO_TOUT;
|
|
p_uart_obj[uart_num]->rx_head_ptr = NULL;
|
|
p_uart_obj[uart_num]->tx_buf_size = tx_buffer_size;
|
|
p_uart_obj[uart_num]->uart_select_notif_callback = NULL;
|
|
xSemaphoreGive(p_uart_obj[uart_num]->tx_fifo_sem);
|
|
uart_pattern_queue_reset(uart_num, UART_PATTERN_DET_QLEN_DEFAULT);
|
|
if (uart_queue) {
|
|
*uart_queue = p_uart_obj[uart_num]->event_queue;
|
|
ESP_LOGI(UART_TAG, "queue free spaces: %d", uxQueueSpacesAvailable(p_uart_obj[uart_num]->event_queue));
|
|
}
|
|
} else {
|
|
ESP_LOGE(UART_TAG, "UART driver already installed");
|
|
return ESP_FAIL;
|
|
}
|
|
|
|
uart_intr_config_t uart_intr = {
|
|
.intr_enable_mask = UART_INTR_CONFIG_FLAG,
|
|
.rxfifo_full_thresh = UART_FULL_THRESH_DEFAULT,
|
|
.rx_timeout_thresh = UART_TOUT_THRESH_DEFAULT,
|
|
.txfifo_empty_intr_thresh = UART_EMPTY_THRESH_DEFAULT,
|
|
};
|
|
uart_module_enable(uart_num);
|
|
uart_hal_disable_intr_mask(&(uart_context[uart_num].hal), UART_LL_INTR_MASK);
|
|
uart_hal_clr_intsts_mask(&(uart_context[uart_num].hal), UART_LL_INTR_MASK);
|
|
r = uart_isr_register(uart_num, uart_rx_intr_handler_default, p_uart_obj[uart_num], intr_alloc_flags, &p_uart_obj[uart_num]->intr_handle);
|
|
if (r != ESP_OK) {
|
|
goto err;
|
|
}
|
|
r = uart_intr_config(uart_num, &uart_intr);
|
|
if (r != ESP_OK) {
|
|
goto err;
|
|
}
|
|
return r;
|
|
|
|
err:
|
|
uart_driver_delete(uart_num);
|
|
return r;
|
|
}
|
|
|
|
//Make sure no other tasks are still using UART before you call this function
|
|
esp_err_t uart_driver_delete(uart_port_t uart_num)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_FAIL);
|
|
if (p_uart_obj[uart_num] == NULL) {
|
|
ESP_LOGI(UART_TAG, "ALREADY NULL");
|
|
return ESP_OK;
|
|
}
|
|
esp_intr_free(p_uart_obj[uart_num]->intr_handle);
|
|
uart_disable_rx_intr(uart_num);
|
|
uart_disable_tx_intr(uart_num);
|
|
uart_pattern_link_free(uart_num);
|
|
uart_free_driver_obj(p_uart_obj[uart_num]);
|
|
p_uart_obj[uart_num] = NULL;
|
|
|
|
#if SOC_UART_SUPPORT_RTC_CLK
|
|
uart_sclk_t sclk = 0;
|
|
uart_hal_get_sclk(&(uart_context[uart_num].hal), &sclk);
|
|
if (sclk == UART_SCLK_RTC) {
|
|
rtc_clk_disable(uart_num);
|
|
}
|
|
#endif
|
|
uart_module_disable(uart_num);
|
|
return ESP_OK;
|
|
}
|
|
|
|
bool uart_is_driver_installed(uart_port_t uart_num)
|
|
{
|
|
return uart_num < UART_NUM_MAX && (p_uart_obj[uart_num] != NULL);
|
|
}
|
|
|
|
void uart_set_select_notif_callback(uart_port_t uart_num, uart_select_notif_callback_t uart_select_notif_callback)
|
|
{
|
|
if (uart_num < UART_NUM_MAX && p_uart_obj[uart_num]) {
|
|
p_uart_obj[uart_num]->uart_select_notif_callback = (uart_select_notif_callback_t) uart_select_notif_callback;
|
|
}
|
|
}
|
|
|
|
portMUX_TYPE *uart_get_selectlock(void)
|
|
{
|
|
return &uart_selectlock;
|
|
}
|
|
|
|
// Set UART mode
|
|
esp_err_t uart_set_mode(uart_port_t uart_num, uart_mode_t mode)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_ERR_INVALID_ARG);
|
|
UART_CHECK((p_uart_obj[uart_num]), "uart driver error", ESP_ERR_INVALID_STATE);
|
|
if ((mode == UART_MODE_RS485_COLLISION_DETECT) || (mode == UART_MODE_RS485_APP_CTRL)
|
|
|| (mode == UART_MODE_RS485_HALF_DUPLEX)) {
|
|
UART_CHECK((!uart_hal_is_hw_rts_en(&(uart_context[uart_num].hal))),
|
|
"disable hw flowctrl before using RS485 mode", ESP_ERR_INVALID_ARG);
|
|
}
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_mode(&(uart_context[uart_num].hal), mode);
|
|
if (mode == UART_MODE_RS485_COLLISION_DETECT) {
|
|
// This mode allows read while transmitting that allows collision detection
|
|
p_uart_obj[uart_num]->coll_det_flg = false;
|
|
// Enable collision detection interrupts
|
|
uart_hal_ena_intr_mask(&(uart_context[uart_num].hal), UART_INTR_RXFIFO_TOUT
|
|
| UART_INTR_RXFIFO_FULL
|
|
| UART_INTR_RS485_CLASH
|
|
| UART_INTR_RS485_FRM_ERR
|
|
| UART_INTR_RS485_PARITY_ERR);
|
|
}
|
|
p_uart_obj[uart_num]->uart_mode = mode;
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_rx_full_threshold(uart_port_t uart_num, int threshold)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_ERR_INVALID_ARG);
|
|
UART_CHECK((threshold < UART_RXFIFO_FULL_THRHD_V) && (threshold > 0),
|
|
"rx fifo full threshold value error", ESP_ERR_INVALID_ARG);
|
|
if (p_uart_obj[uart_num] == NULL) {
|
|
ESP_LOGE(UART_TAG, "call uart_driver_install API first");
|
|
return ESP_ERR_INVALID_STATE;
|
|
}
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
if (uart_hal_get_intr_ena_status(&(uart_context[uart_num].hal)) & UART_INTR_RXFIFO_FULL) {
|
|
uart_hal_set_rxfifo_full_thr(&(uart_context[uart_num].hal), threshold);
|
|
}
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_tx_empty_threshold(uart_port_t uart_num, int threshold)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_ERR_INVALID_ARG);
|
|
UART_CHECK((threshold < UART_TXFIFO_EMPTY_THRHD_V) && (threshold > 0),
|
|
"tx fifo empty threshold value error", ESP_ERR_INVALID_ARG);
|
|
if (p_uart_obj[uart_num] == NULL) {
|
|
ESP_LOGE(UART_TAG, "call uart_driver_install API first");
|
|
return ESP_ERR_INVALID_STATE;
|
|
}
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
if (uart_hal_get_intr_ena_status(&(uart_context[uart_num].hal)) & UART_INTR_TXFIFO_EMPTY) {
|
|
uart_hal_set_txfifo_empty_thr(&(uart_context[uart_num].hal), threshold);
|
|
}
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_rx_timeout(uart_port_t uart_num, const uint8_t tout_thresh)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_ERR_INVALID_ARG);
|
|
// get maximum timeout threshold
|
|
uint16_t tout_max_thresh = uart_hal_get_max_rx_timeout_thrd(&(uart_context[uart_num].hal));
|
|
if (tout_thresh > tout_max_thresh) {
|
|
ESP_LOGE(UART_TAG, "tout_thresh = %d > maximum value = %d", tout_thresh, tout_max_thresh);
|
|
return ESP_ERR_INVALID_ARG;
|
|
}
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_rx_timeout(&(uart_context[uart_num].hal), tout_thresh);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_get_collision_flag(uart_port_t uart_num, bool *collision_flag)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_ERR_INVALID_ARG);
|
|
UART_CHECK((p_uart_obj[uart_num]), "uart driver error", ESP_FAIL);
|
|
UART_CHECK((collision_flag != NULL), "wrong parameter pointer", ESP_ERR_INVALID_ARG);
|
|
UART_CHECK((UART_IS_MODE_SET(uart_num, UART_MODE_RS485_HALF_DUPLEX)
|
|
|| UART_IS_MODE_SET(uart_num, UART_MODE_RS485_COLLISION_DETECT)),
|
|
"wrong mode", ESP_ERR_INVALID_ARG);
|
|
*collision_flag = p_uart_obj[uart_num]->coll_det_flg;
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_wakeup_threshold(uart_port_t uart_num, int wakeup_threshold)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_ERR_INVALID_ARG);
|
|
UART_CHECK((wakeup_threshold <= UART_ACTIVE_THRESHOLD_V &&
|
|
wakeup_threshold > UART_MIN_WAKEUP_THRESH),
|
|
"wakeup_threshold out of bounds", ESP_ERR_INVALID_ARG);
|
|
UART_ENTER_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
uart_hal_set_wakeup_thrd(&(uart_context[uart_num].hal), wakeup_threshold);
|
|
UART_EXIT_CRITICAL(&(uart_context[uart_num].spinlock));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_get_wakeup_threshold(uart_port_t uart_num, int *out_wakeup_threshold)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_ERR_INVALID_ARG);
|
|
UART_CHECK((out_wakeup_threshold != NULL), "argument is NULL", ESP_ERR_INVALID_ARG);
|
|
uart_hal_get_wakeup_thrd(&(uart_context[uart_num].hal), (uint32_t *)out_wakeup_threshold);
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_wait_tx_idle_polling(uart_port_t uart_num)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_ERR_INVALID_ARG);
|
|
while (!uart_hal_is_tx_idle(&(uart_context[uart_num].hal)));
|
|
return ESP_OK;
|
|
}
|
|
|
|
esp_err_t uart_set_loop_back(uart_port_t uart_num, bool loop_back_en)
|
|
{
|
|
UART_CHECK((uart_num < UART_NUM_MAX), "uart_num error", ESP_ERR_INVALID_ARG);
|
|
uart_hal_set_loop_back(&(uart_context[uart_num].hal), loop_back_en);
|
|
return ESP_OK;
|
|
}
|
|
|
|
void uart_set_always_rx_timeout(uart_port_t uart_num, bool always_rx_timeout)
|
|
{
|
|
uint16_t rx_tout = uart_hal_get_rx_tout_thr(&(uart_context[uart_num].hal));
|
|
if (rx_tout) {
|
|
p_uart_obj[uart_num]->rx_always_timeout_flg = always_rx_timeout;
|
|
} else {
|
|
p_uart_obj[uart_num]->rx_always_timeout_flg = false;
|
|
}
|
|
}
|