mirror of https://github.com/espressif/esp-idf.git synced 2024-10-05 20:47:46 -04:00

History

Tomas Rezucha 62091b4fa0 fix(usb/uvc): Add negotiation retry for some cameras Some cameras would refuse first stream format and would only accept on second retry.		2023-11-29 11:34:47 +08:00
..
main	change(usb/examples): Trim the USB example builds	2023-10-10 10:28:47 +02:00
CMakeLists.txt	change(usb/examples): Trim the USB example builds	2023-10-10 10:28:47 +02:00
partitions.csv	usbd: add usb composite device example	2023-04-19 14:02:33 +05:30
pytest_usb_device_composite.py	usbd: add usb composite device example	2023-04-19 14:02:33 +05:30
README.md	usbd: add usb composite device example	2023-04-19 14:02:33 +05:30
sdkconfig.defaults	fix(usb/uvc): Add negotiation retry for some cameras	2023-11-29 11:34:47 +08:00

README.md

Supported Targets	ESP32-S2	ESP32-S3

TinyUSB Composite Device (MSC + Serial) Example

(See the README.md file in the upper level 'examples' directory for more information about examples.)

A USB device can provide multiple functions that are active simultaneously. Such multi-function devices are also known as composite devices. This example shows how to set up ESP chip to work as a USB Serial Device as well as MSC device (Storage media as SPI-Flash).

As a USB stack, a TinyUSB component is used.

How to use example

Hardware Required

Any ESP board that supports the USB-OTG peripheral.

Pin Assignment

Note: In case your board doesn't have micro-USB connector connected to USB-OTG peripheral, you may have to DIY a cable and connect D+ and D- to the pins listed below.

See common pin assignments for USB Device examples from upper level.

Next, for Self-Powered Devices with VBUS monitoring, user must set self_powered to true and vbus_monitor_io to GPIO number (VBUS_MONITORING_GPIO_NUM) that will be used for VBUS monitoring.

Build and Flash

Build the project and flash it to the board, then run monitor tool to view serial output:

idf.py -p PORT flash monitor

(Replace PORT with the name of the serial port to use.)

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

Example Output

After the flashing you should see the output at idf monitor:

I (344) main_task: Calling app_main()
I (344) example_main: USB Composite initialization
W (354) TinyUSB: The device's configuration descriptor is not provided by user, using default.
W (364) TinyUSB: The device's string descriptor is not provided by user, using default.
W (374) TinyUSB: The device's device descriptor is not provided by user, using default.
I (384) tusb_desc:
┌─────────────────────────────────┐
│  USB Device Descriptor Summary  │
├───────────────────┬─────────────┤
│bDeviceClass       │ 239         │
├───────────────────┼─────────────┤
│bDeviceSubClass    │ 2           │
├───────────────────┼─────────────┤
│bDeviceProtocol    │ 1           │
├───────────────────┼─────────────┤
│bMaxPacketSize0    │ 64          │
├───────────────────┼─────────────┤
│idVendor           │ 0x303a      │
├───────────────────┼─────────────┤
│idProduct          │ 0x4001      │
├───────────────────┼─────────────┤
│bcdDevice          │ 0x100       │
├───────────────────┼─────────────┤
│iManufacturer      │ 0x1         │
├───────────────────┼─────────────┤
│iProduct           │ 0x2         │
├───────────────────┼─────────────┤
│iSerialNumber      │ 0x3         │
├───────────────────┼─────────────┤
│bNumConfigurations │ 0x1         │
└───────────────────┴─────────────┘
I (544) TinyUSB: TinyUSB Driver installed
I (554) example_main: Initializing storage...
I (554) example_main: Initializing wear levelling
I (584) example_main: USB Composite initialization DONE
I (584) main_task: Returned from app_main()