mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
20b7f0ec87
1. fix infinite loop problem when init phy device 2. fix infinite loop problem when reset mac 3. fix little bugs in ethernetif_init 4. fix incompatible return value between lwip and esp-idf Closes https://github.com/espressif/esp-idf/issues/2331 Closes https://github.com/espressif/esp-idf/issues/2141
67 lines
1.9 KiB
C
67 lines
1.9 KiB
C
// Copyright 2015-2017 Espressif Systems (Shanghai) PTE LTD
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
#pragma once
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
#include "phy.h"
|
|
|
|
/** @brief Dump all TLK110 PHY SMI configuration registers
|
|
*
|
|
* @note These registers are dumped at 'debug' level, so output
|
|
* may not be visible depending on default log levels.
|
|
*/
|
|
void phy_tlk110_dump_registers();
|
|
|
|
/** @brief Default TLK110 phy_check_init function.
|
|
*/
|
|
void phy_tlk110_check_phy_init(void);
|
|
|
|
/** @brief Default TLK110 phy_get_speed_mode function.
|
|
*/
|
|
eth_speed_mode_t phy_tlk110_get_speed_mode(void);
|
|
|
|
/** @brief Default TLK110 phy_get_duplex_mode function.
|
|
*/
|
|
eth_duplex_mode_t phy_tlk110_get_duplex_mode(void);
|
|
|
|
/** @brief Default TLK110 phy_power_enable function.
|
|
*
|
|
* @note This function may need to be replaced with a custom function
|
|
* if the PHY has a GPIO to enable power or start a clock.
|
|
*
|
|
* Consult the ethernet example to see how this is done.
|
|
*/
|
|
void phy_tlk110_power_enable(bool);
|
|
|
|
/** @brief Default TLK110 phy_init function.
|
|
*/
|
|
esp_err_t phy_tlk110_init(void);
|
|
|
|
/** @brief Default TLK110 PHY configuration
|
|
*
|
|
* This configuration is not suitable for use as-is, it will need
|
|
* to be modified for your particular PHY hardware setup.
|
|
*
|
|
* Consult the Ethernet example to see how this is done.
|
|
*/
|
|
extern const eth_config_t phy_tlk110_default_ethernet_config;
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|