esp-idf/examples/security/flash_encryption
Cao Sen Miao 44e16a6401 fix(spi_flash): Fix issue that flash encryption failed while rom_impl config is enabled
The issue is `esp_flash_write_encryped` function in ROM on ESP32C3, ESP32S3
calls legacy implementation, which uses old configuration. And this causes
write fails.
The solution in this commit is to compile and link this function(and related)
in IRAM instead of the ROM one.
The IRAM cost increases around 1.2KB after the fix
2024-02-28 10:07:53 +08:00
..
main protocols/security: Remove -Wno-format compile option for examples 2022-12-07 13:02:00 +05:30
CMakeLists.txt tools: Increase the minimal supported CMake version to 3.16 2022-06-01 06:35:02 +00:00
partitions_example.csv examples/security: add support for initializing custom NVS partition with encryption 2022-06-02 18:13:43 +05:30
pytest_flash_encryption.py fix(spi_flash): Fix issue that flash encryption failed while rom_impl config is enabled 2024-02-28 10:07:53 +08:00
README.md feat(ci): Enable p4 example, test_apps and unit tests CI build 2023-08-24 12:51:19 +08:00
sample_encryption_keys.bin nvs_flash: Modify the default NVS initialization API with internal nvs encryption 2021-01-20 11:12:14 +00:00
sdkconfig.ci example_tests: Deletes usage esp32c3 ECO0 in CI (by default ECO3) 2021-09-24 13:55:07 +08:00
sdkconfig.ci.rom_impl fix(spi_flash): Fix issue that flash encryption failed while rom_impl config is enabled 2024-02-28 10:07:53 +08:00
sdkconfig.defaults fix: fixed build issue in flash encryption example with certain config 2023-11-28 12:41:35 +05:30

Supported Targets ESP32 ESP32-C2 ESP32-C3 ESP32-C6 ESP32-H2 ESP32-P4 ESP32-S2 ESP32-S3

Flash Encryption

The example checks if the flash encryption feature is enabled/disabled and if enabled prints the flash encryption mode (DEVELOPMENT / RELEASE) and FLASH_CRYPT_CNT (for ESP32) or SPI_BOOT_CRYPT_CNT (for ESP32-S2 and newer targets) eFuse value.

The example also demonstrates writing and reading encrypted partitions in flash.

How to use example

Hardware Required

Configure the project

idf.py menuconfig

Configuration for flash encryption

  • Enable the flash encryption mode (Development or Release) under Security Features. Default usage mode is Development (recommended during test and development phase).

Note: After enabling flash encryption, the bootloader size increases, which means that the offset of the partition table must be changed to 0x9000 from 0x8000 to prevent the bootloader from overlapping with the partition table. In this example, the default offset of the partition table is 0x9000.

For better security, the NVS encryption is enabled by default when the flash encryption is enabled. If you choose to disable the NVS encryption, you can skip the NVS configuration step given below.

Configuration for NVS encryption

For using NVS encryption, the partition table must contain the NVS key partition. Two partition tables containing the NVS keys partition are provided for NVS encryption under the partition table option . They can be selected with the project configuration menu (menuconfig -> Partition Table). This particular example uses a custom partition table as it requires a storage partition along with the nvs_keys partition.

The configuration for NVS encryption involves generating the XTS encryption keys in the NVS key partition partition. It can be done with one of the following method.

  1. Generate the XTS encryption keys on the ESP chip:

    When NVS encryption is enabled the nvs_flash_init API function can internally generate the XTS encryption keys on the ESP chip. The API function finds the first NVS key partition i.e. a partition of type data and subtype nvs_keys. Then the API function automatically generates and stores the nvs keys in that partition. New keys are generated and stored only when the respective key partiton is empty. (Consult the nvs_flash_init API documentation in the ESP-IDF programming guide for more details).

    Please note that nvs_keys partition must be completely erased before starting the application. Otherwise the application may generate ESP_ERR_NVS_CORRUPT_KEY_PART error code assuming that nvs_keys partition was not empty and contains malformatted data.

  2. Use pre-generated XTS encryption keys: This method will be required by the user when the XTS encryption keys in NVS key partition are not generated by the application. The pre generated Sample XTS encryption keys can be stored on the flash with help of the following two commands

    i) Build and flash the partition table:

    idf.py partition-table partition-table-flash
    

    ii) Store the sample_encryption_keys.bin in the nvs_keypartition (on the flash) with the help of parttool.py:

    parttool.py --port /dev/ttyUSB0 --partition-table-offset 0x9000 write_partition --partition-name="nvs_key" --input sample_encryption_keys.bin
    

    The sample NVS key partition partition used in this example is generated with the help of NVS Partition Generator Utility .

Build and Flash

When building the project and flashing it to the board FOR THE FIRST TIME after enabling flash encryption feature in menuconfig, run following command to program the target and monitor the output:

idf.py -p PORT flash monitor

(To exit the serial monitor, type Ctrl-].)

See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.

When reprogramming the device subsequently use following command for encrypted write of new plaintext application:

idf.py -p PORT encrypted-app-flash monitor

Please note above command programs only the app partition. In order to reprogram all partitions (bootloader, partition table and application) in encrypted form use:

idf.py -p PORT encrypted-flash monitor

Example Output

When running the example without enabling flash encryption, the output would be as follows (on ESP32):

Example to check Flash Encryption status
This is ESP32 chip with 2 CPU cores, WiFi/BT/BLE, silicon revision 0, 2MB external flash
FLASH_CRYPT_CNT eFuse value is 0
Flash encryption feature is disabled
Erasing partition "storage" (0x1000 bytes)
Writing data with esp_partition_write:
I (378) example: 0x3ffb4dc0   00 01 02 03 04 05 06 07  08 09 0a 0b 0c 0d 0e 0f  |................|
I (378) example: 0x3ffb4dd0   10 11 12 13 14 15 16 17  18 19 1a 1b 1c 1d 1e 1f  |................|
Reading with esp_partition_read:
I (388) example: 0x3ffb4da0   00 01 02 03 04 05 06 07  08 09 0a 0b 0c 0d 0e 0f  |................|
I (398) example: 0x3ffb4db0   10 11 12 13 14 15 16 17  18 19 1a 1b 1c 1d 1e 1f  |................|
Reading with spi_flash_read:
I (408) example: 0x3ffb4da0   00 01 02 03 04 05 06 07  08 09 0a 0b 0c 0d 0e 0f  |................|
I (418) example: 0x3ffb4db0   10 11 12 13 14 15 16 17  18 19 1a 1b 1c 1d 1e 1f  |................|

After enabling flash encryption in Development mode, the output shows the process of enabling the flash encryption:

I (168) boot: Checking flash encryption...
I (168) flash_encrypt: Generating new flash encryption key...
I (187) flash_encrypt: Read & write protecting new key...
I (187) flash_encrypt: Setting CRYPT_CONFIG efuse to 0xF
W (188) flash_encrypt: Not disabling UART bootloader encryption
I (195) flash_encrypt: Disable UART bootloader decryption...
I (201) flash_encrypt: Disable UART bootloader MMU cache...
I (208) flash_encrypt: Disable JTAG...
I (212) flash_encrypt: Disable ROM BASIC interpreter fallback...
....
....
....
I (13229) flash_encrypt: Flash encryption completed
I (13229) boot: Resetting with flash encryption enabled...

Once the flash encryption is enabled the device will reset itself. At this stage the flash contents are in encrypted form. The output would be similar to:

Example to check Flash Encryption status
This is ESP32 chip with 2 CPU cores, WiFi/BT/BLE, silicon revision 0, 4MB external flash
FLASH_CRYPT_CNT eFuse value is 1
Flash encryption feature is enabled in DEVELOPMENT mode
Erasing partition "storage" (0x1000 bytes)
Writing data with esp_partition_write:
I (451) example: 0x3ffb4dc0   00 01 02 03 04 05 06 07  08 09 0a 0b 0c 0d 0e 0f  |................|
I (451) example: 0x3ffb4dd0   10 11 12 13 14 15 16 17  18 19 1a 1b 1c 1d 1e 1f  |................|
Reading with esp_partition_read:
I (461) example: 0x3ffb4da0   00 01 02 03 04 05 06 07  08 09 0a 0b 0c 0d 0e 0f  |................|
I (471) example: 0x3ffb4db0   10 11 12 13 14 15 16 17  18 19 1a 1b 1c 1d 1e 1f  |................|
Reading with spi_flash_read:
I (491) example: 0x3ffb4b30   35 9b f2 07 b4 6d 40 89  28 b4 1e 22 98 7b 4a 36  |5....m@.(..".{J6|
I (491) example: 0x3ffb4b40   ba 89 81 67 77 a3 60 5e  0a e7 51 01 b3 58 c2 f6  |...gw.`^..Q..X..|

If the NVS encryption is enabled, then the output will show the status of the encrypted partition as follows

I (667) example_nvs: NVS partition "nvs" is encrypted.

Troubleshooting

It is also possible to use esptool.py utility to read the eFuse values and check if flash encryption is enabled or not

python $IDF_PATH/components/esptool_py/esptool/espefuse.py --port PORT summary

If FLASH_CRYPT_CNT (for ESP32) or SPI_BOOT_CRYPT_CNT (for ESP32-S2 and newer targets) eFuse value is non-zero flash encryption is enabled