mirror of
https://github.com/espressif/esp-idf.git
synced 2024-10-05 20:47:46 -04:00
1347 lines
60 KiB
C
1347 lines
60 KiB
C
/**
|
|
* SPDX-FileCopyrightText: 2023 Espressif Systems (Shanghai) CO LTD
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
#pragma once
|
|
|
|
#include <stdint.h>
|
|
#include "soc/soc.h"
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
/** PCNT_U0_CONF0_REG register
|
|
* Configuration register 0 for unit 0
|
|
*/
|
|
#define PCNT_U0_CONF0_REG (DR_REG_PCNT_BASE + 0x0)
|
|
/** PCNT_FILTER_THRES_U0 : R/W; bitpos: [9:0]; default: 16;
|
|
* This sets the maximum threshold, in APB_CLK cycles, for the filter.
|
|
*
|
|
* Any pulses with width less than this will be ignored when the filter is enabled.
|
|
*/
|
|
#define PCNT_FILTER_THRES_U0 0x000003FFU
|
|
#define PCNT_FILTER_THRES_U0_M (PCNT_FILTER_THRES_U0_V << PCNT_FILTER_THRES_U0_S)
|
|
#define PCNT_FILTER_THRES_U0_V 0x000003FFU
|
|
#define PCNT_FILTER_THRES_U0_S 0
|
|
/** PCNT_FILTER_EN_U0 : R/W; bitpos: [10]; default: 1;
|
|
* This is the enable bit for unit 0's input filter.
|
|
*/
|
|
#define PCNT_FILTER_EN_U0 (BIT(10))
|
|
#define PCNT_FILTER_EN_U0_M (PCNT_FILTER_EN_U0_V << PCNT_FILTER_EN_U0_S)
|
|
#define PCNT_FILTER_EN_U0_V 0x00000001U
|
|
#define PCNT_FILTER_EN_U0_S 10
|
|
/** PCNT_THR_ZERO_EN_U0 : R/W; bitpos: [11]; default: 1;
|
|
* This is the enable bit for unit 0's zero comparator.
|
|
*/
|
|
#define PCNT_THR_ZERO_EN_U0 (BIT(11))
|
|
#define PCNT_THR_ZERO_EN_U0_M (PCNT_THR_ZERO_EN_U0_V << PCNT_THR_ZERO_EN_U0_S)
|
|
#define PCNT_THR_ZERO_EN_U0_V 0x00000001U
|
|
#define PCNT_THR_ZERO_EN_U0_S 11
|
|
/** PCNT_THR_H_LIM_EN_U0 : R/W; bitpos: [12]; default: 1;
|
|
* This is the enable bit for unit 0's thr_h_lim comparator. Configures it to enable
|
|
* the high limit interrupt.
|
|
*/
|
|
#define PCNT_THR_H_LIM_EN_U0 (BIT(12))
|
|
#define PCNT_THR_H_LIM_EN_U0_M (PCNT_THR_H_LIM_EN_U0_V << PCNT_THR_H_LIM_EN_U0_S)
|
|
#define PCNT_THR_H_LIM_EN_U0_V 0x00000001U
|
|
#define PCNT_THR_H_LIM_EN_U0_S 12
|
|
/** PCNT_THR_L_LIM_EN_U0 : R/W; bitpos: [13]; default: 1;
|
|
* This is the enable bit for unit 0's thr_l_lim comparator. Configures it to enable
|
|
* the low limit interrupt.
|
|
*/
|
|
#define PCNT_THR_L_LIM_EN_U0 (BIT(13))
|
|
#define PCNT_THR_L_LIM_EN_U0_M (PCNT_THR_L_LIM_EN_U0_V << PCNT_THR_L_LIM_EN_U0_S)
|
|
#define PCNT_THR_L_LIM_EN_U0_V 0x00000001U
|
|
#define PCNT_THR_L_LIM_EN_U0_S 13
|
|
/** PCNT_THR_THRES0_EN_U0 : R/W; bitpos: [14]; default: 0;
|
|
* This is the enable bit for unit 0's thres0 comparator.
|
|
*/
|
|
#define PCNT_THR_THRES0_EN_U0 (BIT(14))
|
|
#define PCNT_THR_THRES0_EN_U0_M (PCNT_THR_THRES0_EN_U0_V << PCNT_THR_THRES0_EN_U0_S)
|
|
#define PCNT_THR_THRES0_EN_U0_V 0x00000001U
|
|
#define PCNT_THR_THRES0_EN_U0_S 14
|
|
/** PCNT_THR_THRES1_EN_U0 : R/W; bitpos: [15]; default: 0;
|
|
* This is the enable bit for unit 0's thres1 comparator.
|
|
*/
|
|
#define PCNT_THR_THRES1_EN_U0 (BIT(15))
|
|
#define PCNT_THR_THRES1_EN_U0_M (PCNT_THR_THRES1_EN_U0_V << PCNT_THR_THRES1_EN_U0_S)
|
|
#define PCNT_THR_THRES1_EN_U0_V 0x00000001U
|
|
#define PCNT_THR_THRES1_EN_U0_S 15
|
|
/** PCNT_CH0_NEG_MODE_U0 : R/W; bitpos: [17:16]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 0 detects a
|
|
* negative edge.
|
|
*
|
|
* 1: Increase the counter.2: Decrease the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH0_NEG_MODE_U0 0x00000003U
|
|
#define PCNT_CH0_NEG_MODE_U0_M (PCNT_CH0_NEG_MODE_U0_V << PCNT_CH0_NEG_MODE_U0_S)
|
|
#define PCNT_CH0_NEG_MODE_U0_V 0x00000003U
|
|
#define PCNT_CH0_NEG_MODE_U0_S 16
|
|
/** PCNT_CH0_POS_MODE_U0 : R/W; bitpos: [19:18]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 0 detects a
|
|
* positive edge.
|
|
*
|
|
* 1: Increase the counter.2: Decrease the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH0_POS_MODE_U0 0x00000003U
|
|
#define PCNT_CH0_POS_MODE_U0_M (PCNT_CH0_POS_MODE_U0_V << PCNT_CH0_POS_MODE_U0_S)
|
|
#define PCNT_CH0_POS_MODE_U0_V 0x00000003U
|
|
#define PCNT_CH0_POS_MODE_U0_S 18
|
|
/** PCNT_CH0_HCTRL_MODE_U0 : R/W; bitpos: [21:20]; default: 0;
|
|
* This register configures how the CH0_POS_MODE/CH0_NEG_MODE settings will be
|
|
* modified when the control signal is high.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH0_HCTRL_MODE_U0 0x00000003U
|
|
#define PCNT_CH0_HCTRL_MODE_U0_M (PCNT_CH0_HCTRL_MODE_U0_V << PCNT_CH0_HCTRL_MODE_U0_S)
|
|
#define PCNT_CH0_HCTRL_MODE_U0_V 0x00000003U
|
|
#define PCNT_CH0_HCTRL_MODE_U0_S 20
|
|
/** PCNT_CH0_LCTRL_MODE_U0 : R/W; bitpos: [23:22]; default: 0;
|
|
* This register configures how the CH0_POS_MODE/CH0_NEG_MODE settings will be
|
|
* modified when the control signal is low.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH0_LCTRL_MODE_U0 0x00000003U
|
|
#define PCNT_CH0_LCTRL_MODE_U0_M (PCNT_CH0_LCTRL_MODE_U0_V << PCNT_CH0_LCTRL_MODE_U0_S)
|
|
#define PCNT_CH0_LCTRL_MODE_U0_V 0x00000003U
|
|
#define PCNT_CH0_LCTRL_MODE_U0_S 22
|
|
/** PCNT_CH1_NEG_MODE_U0 : R/W; bitpos: [25:24]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 1 detects a
|
|
* negative edge.
|
|
*
|
|
* 1: Increment the counter.2: Decrement the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH1_NEG_MODE_U0 0x00000003U
|
|
#define PCNT_CH1_NEG_MODE_U0_M (PCNT_CH1_NEG_MODE_U0_V << PCNT_CH1_NEG_MODE_U0_S)
|
|
#define PCNT_CH1_NEG_MODE_U0_V 0x00000003U
|
|
#define PCNT_CH1_NEG_MODE_U0_S 24
|
|
/** PCNT_CH1_POS_MODE_U0 : R/W; bitpos: [27:26]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 1 detects a
|
|
* positive edge.
|
|
*
|
|
* 1: Increment the counter.2: Decrement the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH1_POS_MODE_U0 0x00000003U
|
|
#define PCNT_CH1_POS_MODE_U0_M (PCNT_CH1_POS_MODE_U0_V << PCNT_CH1_POS_MODE_U0_S)
|
|
#define PCNT_CH1_POS_MODE_U0_V 0x00000003U
|
|
#define PCNT_CH1_POS_MODE_U0_S 26
|
|
/** PCNT_CH1_HCTRL_MODE_U0 : R/W; bitpos: [29:28]; default: 0;
|
|
* This register configures how the CH0_POS_MODE/CH0_NEG_MODE settings will be
|
|
* modified when the control signal is high.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH1_HCTRL_MODE_U0 0x00000003U
|
|
#define PCNT_CH1_HCTRL_MODE_U0_M (PCNT_CH1_HCTRL_MODE_U0_V << PCNT_CH1_HCTRL_MODE_U0_S)
|
|
#define PCNT_CH1_HCTRL_MODE_U0_V 0x00000003U
|
|
#define PCNT_CH1_HCTRL_MODE_U0_S 28
|
|
/** PCNT_CH1_LCTRL_MODE_U0 : R/W; bitpos: [31:30]; default: 0;
|
|
* This register configures how the CH0_POS_MODE/CH0_NEG_MODE settings will be
|
|
* modified when the control signal is low.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH1_LCTRL_MODE_U0 0x00000003U
|
|
#define PCNT_CH1_LCTRL_MODE_U0_M (PCNT_CH1_LCTRL_MODE_U0_V << PCNT_CH1_LCTRL_MODE_U0_S)
|
|
#define PCNT_CH1_LCTRL_MODE_U0_V 0x00000003U
|
|
#define PCNT_CH1_LCTRL_MODE_U0_S 30
|
|
|
|
/** PCNT_U0_CONF1_REG register
|
|
* Configuration register 1 for unit 0
|
|
*/
|
|
#define PCNT_U0_CONF1_REG (DR_REG_PCNT_BASE + 0x4)
|
|
/** PCNT_CNT_THRES0_U0 : R/W; bitpos: [15:0]; default: 0;
|
|
* This register is used to configure the thres0 value for unit 0.
|
|
*/
|
|
#define PCNT_CNT_THRES0_U0 0x0000FFFFU
|
|
#define PCNT_CNT_THRES0_U0_M (PCNT_CNT_THRES0_U0_V << PCNT_CNT_THRES0_U0_S)
|
|
#define PCNT_CNT_THRES0_U0_V 0x0000FFFFU
|
|
#define PCNT_CNT_THRES0_U0_S 0
|
|
/** PCNT_CNT_THRES1_U0 : R/W; bitpos: [31:16]; default: 0;
|
|
* This register is used to configure the thres1 value for unit 0.
|
|
*/
|
|
#define PCNT_CNT_THRES1_U0 0x0000FFFFU
|
|
#define PCNT_CNT_THRES1_U0_M (PCNT_CNT_THRES1_U0_V << PCNT_CNT_THRES1_U0_S)
|
|
#define PCNT_CNT_THRES1_U0_V 0x0000FFFFU
|
|
#define PCNT_CNT_THRES1_U0_S 16
|
|
|
|
/** PCNT_U0_CONF2_REG register
|
|
* Configuration register 2 for unit 0
|
|
*/
|
|
#define PCNT_U0_CONF2_REG (DR_REG_PCNT_BASE + 0x8)
|
|
/** PCNT_CNT_H_LIM_U0 : R/W; bitpos: [15:0]; default: 0;
|
|
* This register is used to configure the thr_h_lim value for unit 0. When pcnt
|
|
* reaches this value, the counter will be cleared to 0.
|
|
*/
|
|
#define PCNT_CNT_H_LIM_U0 0x0000FFFFU
|
|
#define PCNT_CNT_H_LIM_U0_M (PCNT_CNT_H_LIM_U0_V << PCNT_CNT_H_LIM_U0_S)
|
|
#define PCNT_CNT_H_LIM_U0_V 0x0000FFFFU
|
|
#define PCNT_CNT_H_LIM_U0_S 0
|
|
/** PCNT_CNT_L_LIM_U0 : R/W; bitpos: [31:16]; default: 0;
|
|
* This register is used to configure the thr_l_lim value for unit 0. When pcnt
|
|
* reaches this value, the counter will be cleared to 0.
|
|
*/
|
|
#define PCNT_CNT_L_LIM_U0 0x0000FFFFU
|
|
#define PCNT_CNT_L_LIM_U0_M (PCNT_CNT_L_LIM_U0_V << PCNT_CNT_L_LIM_U0_S)
|
|
#define PCNT_CNT_L_LIM_U0_V 0x0000FFFFU
|
|
#define PCNT_CNT_L_LIM_U0_S 16
|
|
|
|
/** PCNT_U1_CONF0_REG register
|
|
* Configuration register 0 for unit 1
|
|
*/
|
|
#define PCNT_U1_CONF0_REG (DR_REG_PCNT_BASE + 0xc)
|
|
/** PCNT_FILTER_THRES_U1 : R/W; bitpos: [9:0]; default: 16;
|
|
* This sets the maximum threshold, in APB_CLK cycles, for the filter.
|
|
*
|
|
* Any pulses with width less than this will be ignored when the filter is enabled.
|
|
*/
|
|
#define PCNT_FILTER_THRES_U1 0x000003FFU
|
|
#define PCNT_FILTER_THRES_U1_M (PCNT_FILTER_THRES_U1_V << PCNT_FILTER_THRES_U1_S)
|
|
#define PCNT_FILTER_THRES_U1_V 0x000003FFU
|
|
#define PCNT_FILTER_THRES_U1_S 0
|
|
/** PCNT_FILTER_EN_U1 : R/W; bitpos: [10]; default: 1;
|
|
* This is the enable bit for unit 1's input filter.
|
|
*/
|
|
#define PCNT_FILTER_EN_U1 (BIT(10))
|
|
#define PCNT_FILTER_EN_U1_M (PCNT_FILTER_EN_U1_V << PCNT_FILTER_EN_U1_S)
|
|
#define PCNT_FILTER_EN_U1_V 0x00000001U
|
|
#define PCNT_FILTER_EN_U1_S 10
|
|
/** PCNT_THR_ZERO_EN_U1 : R/W; bitpos: [11]; default: 1;
|
|
* This is the enable bit for unit 1's zero comparator.
|
|
*/
|
|
#define PCNT_THR_ZERO_EN_U1 (BIT(11))
|
|
#define PCNT_THR_ZERO_EN_U1_M (PCNT_THR_ZERO_EN_U1_V << PCNT_THR_ZERO_EN_U1_S)
|
|
#define PCNT_THR_ZERO_EN_U1_V 0x00000001U
|
|
#define PCNT_THR_ZERO_EN_U1_S 11
|
|
/** PCNT_THR_H_LIM_EN_U1 : R/W; bitpos: [12]; default: 1;
|
|
* This is the enable bit for unit 1's thr_h_lim comparator. Configures it to enable
|
|
* the high limit interrupt.
|
|
*/
|
|
#define PCNT_THR_H_LIM_EN_U1 (BIT(12))
|
|
#define PCNT_THR_H_LIM_EN_U1_M (PCNT_THR_H_LIM_EN_U1_V << PCNT_THR_H_LIM_EN_U1_S)
|
|
#define PCNT_THR_H_LIM_EN_U1_V 0x00000001U
|
|
#define PCNT_THR_H_LIM_EN_U1_S 12
|
|
/** PCNT_THR_L_LIM_EN_U1 : R/W; bitpos: [13]; default: 1;
|
|
* This is the enable bit for unit 1's thr_l_lim comparator. Configures it to enable
|
|
* the low limit interrupt.
|
|
*/
|
|
#define PCNT_THR_L_LIM_EN_U1 (BIT(13))
|
|
#define PCNT_THR_L_LIM_EN_U1_M (PCNT_THR_L_LIM_EN_U1_V << PCNT_THR_L_LIM_EN_U1_S)
|
|
#define PCNT_THR_L_LIM_EN_U1_V 0x00000001U
|
|
#define PCNT_THR_L_LIM_EN_U1_S 13
|
|
/** PCNT_THR_THRES0_EN_U1 : R/W; bitpos: [14]; default: 0;
|
|
* This is the enable bit for unit 1's thres0 comparator.
|
|
*/
|
|
#define PCNT_THR_THRES0_EN_U1 (BIT(14))
|
|
#define PCNT_THR_THRES0_EN_U1_M (PCNT_THR_THRES0_EN_U1_V << PCNT_THR_THRES0_EN_U1_S)
|
|
#define PCNT_THR_THRES0_EN_U1_V 0x00000001U
|
|
#define PCNT_THR_THRES0_EN_U1_S 14
|
|
/** PCNT_THR_THRES1_EN_U1 : R/W; bitpos: [15]; default: 0;
|
|
* This is the enable bit for unit 1's thres1 comparator.
|
|
*/
|
|
#define PCNT_THR_THRES1_EN_U1 (BIT(15))
|
|
#define PCNT_THR_THRES1_EN_U1_M (PCNT_THR_THRES1_EN_U1_V << PCNT_THR_THRES1_EN_U1_S)
|
|
#define PCNT_THR_THRES1_EN_U1_V 0x00000001U
|
|
#define PCNT_THR_THRES1_EN_U1_S 15
|
|
/** PCNT_CH0_NEG_MODE_U1 : R/W; bitpos: [17:16]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 0 detects a
|
|
* negative edge.
|
|
*
|
|
* 1: Increase the counter.2: Decrease the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH0_NEG_MODE_U1 0x00000003U
|
|
#define PCNT_CH0_NEG_MODE_U1_M (PCNT_CH0_NEG_MODE_U1_V << PCNT_CH0_NEG_MODE_U1_S)
|
|
#define PCNT_CH0_NEG_MODE_U1_V 0x00000003U
|
|
#define PCNT_CH0_NEG_MODE_U1_S 16
|
|
/** PCNT_CH0_POS_MODE_U1 : R/W; bitpos: [19:18]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 0 detects a
|
|
* positive edge.
|
|
*
|
|
* 1: Increase the counter.2: Decrease the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH0_POS_MODE_U1 0x00000003U
|
|
#define PCNT_CH0_POS_MODE_U1_M (PCNT_CH0_POS_MODE_U1_V << PCNT_CH0_POS_MODE_U1_S)
|
|
#define PCNT_CH0_POS_MODE_U1_V 0x00000003U
|
|
#define PCNT_CH0_POS_MODE_U1_S 18
|
|
/** PCNT_CH0_HCTRL_MODE_U1 : R/W; bitpos: [21:20]; default: 0;
|
|
* This register configures how the CH1_POS_MODE/CH1_NEG_MODE settings will be
|
|
* modified when the control signal is high.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH0_HCTRL_MODE_U1 0x00000003U
|
|
#define PCNT_CH0_HCTRL_MODE_U1_M (PCNT_CH0_HCTRL_MODE_U1_V << PCNT_CH0_HCTRL_MODE_U1_S)
|
|
#define PCNT_CH0_HCTRL_MODE_U1_V 0x00000003U
|
|
#define PCNT_CH0_HCTRL_MODE_U1_S 20
|
|
/** PCNT_CH0_LCTRL_MODE_U1 : R/W; bitpos: [23:22]; default: 0;
|
|
* This register configures how the CH1_POS_MODE/CH1_NEG_MODE settings will be
|
|
* modified when the control signal is low.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH0_LCTRL_MODE_U1 0x00000003U
|
|
#define PCNT_CH0_LCTRL_MODE_U1_M (PCNT_CH0_LCTRL_MODE_U1_V << PCNT_CH0_LCTRL_MODE_U1_S)
|
|
#define PCNT_CH0_LCTRL_MODE_U1_V 0x00000003U
|
|
#define PCNT_CH0_LCTRL_MODE_U1_S 22
|
|
/** PCNT_CH1_NEG_MODE_U1 : R/W; bitpos: [25:24]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 1 detects a
|
|
* negative edge.
|
|
*
|
|
* 1: Increment the counter.2: Decrement the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH1_NEG_MODE_U1 0x00000003U
|
|
#define PCNT_CH1_NEG_MODE_U1_M (PCNT_CH1_NEG_MODE_U1_V << PCNT_CH1_NEG_MODE_U1_S)
|
|
#define PCNT_CH1_NEG_MODE_U1_V 0x00000003U
|
|
#define PCNT_CH1_NEG_MODE_U1_S 24
|
|
/** PCNT_CH1_POS_MODE_U1 : R/W; bitpos: [27:26]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 1 detects a
|
|
* positive edge.
|
|
*
|
|
* 1: Increment the counter.2: Decrement the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH1_POS_MODE_U1 0x00000003U
|
|
#define PCNT_CH1_POS_MODE_U1_M (PCNT_CH1_POS_MODE_U1_V << PCNT_CH1_POS_MODE_U1_S)
|
|
#define PCNT_CH1_POS_MODE_U1_V 0x00000003U
|
|
#define PCNT_CH1_POS_MODE_U1_S 26
|
|
/** PCNT_CH1_HCTRL_MODE_U1 : R/W; bitpos: [29:28]; default: 0;
|
|
* This register configures how the CH1_POS_MODE/CH1_NEG_MODE settings will be
|
|
* modified when the control signal is high.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH1_HCTRL_MODE_U1 0x00000003U
|
|
#define PCNT_CH1_HCTRL_MODE_U1_M (PCNT_CH1_HCTRL_MODE_U1_V << PCNT_CH1_HCTRL_MODE_U1_S)
|
|
#define PCNT_CH1_HCTRL_MODE_U1_V 0x00000003U
|
|
#define PCNT_CH1_HCTRL_MODE_U1_S 28
|
|
/** PCNT_CH1_LCTRL_MODE_U1 : R/W; bitpos: [31:30]; default: 0;
|
|
* This register configures how the CH1_POS_MODE/CH1_NEG_MODE settings will be
|
|
* modified when the control signal is low.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH1_LCTRL_MODE_U1 0x00000003U
|
|
#define PCNT_CH1_LCTRL_MODE_U1_M (PCNT_CH1_LCTRL_MODE_U1_V << PCNT_CH1_LCTRL_MODE_U1_S)
|
|
#define PCNT_CH1_LCTRL_MODE_U1_V 0x00000003U
|
|
#define PCNT_CH1_LCTRL_MODE_U1_S 30
|
|
|
|
/** PCNT_U1_CONF1_REG register
|
|
* Configuration register 1 for unit 1
|
|
*/
|
|
#define PCNT_U1_CONF1_REG (DR_REG_PCNT_BASE + 0x10)
|
|
/** PCNT_CNT_THRES0_U1 : R/W; bitpos: [15:0]; default: 0;
|
|
* This register is used to configure the thres0 value for unit 1.
|
|
*/
|
|
#define PCNT_CNT_THRES0_U1 0x0000FFFFU
|
|
#define PCNT_CNT_THRES0_U1_M (PCNT_CNT_THRES0_U1_V << PCNT_CNT_THRES0_U1_S)
|
|
#define PCNT_CNT_THRES0_U1_V 0x0000FFFFU
|
|
#define PCNT_CNT_THRES0_U1_S 0
|
|
/** PCNT_CNT_THRES1_U1 : R/W; bitpos: [31:16]; default: 0;
|
|
* This register is used to configure the thres1 value for unit 1.
|
|
*/
|
|
#define PCNT_CNT_THRES1_U1 0x0000FFFFU
|
|
#define PCNT_CNT_THRES1_U1_M (PCNT_CNT_THRES1_U1_V << PCNT_CNT_THRES1_U1_S)
|
|
#define PCNT_CNT_THRES1_U1_V 0x0000FFFFU
|
|
#define PCNT_CNT_THRES1_U1_S 16
|
|
|
|
/** PCNT_U1_CONF2_REG register
|
|
* Configuration register 2 for unit 1
|
|
*/
|
|
#define PCNT_U1_CONF2_REG (DR_REG_PCNT_BASE + 0x14)
|
|
/** PCNT_CNT_H_LIM_U1 : R/W; bitpos: [15:0]; default: 0;
|
|
* This register is used to configure the thr_h_lim value for unit 1. When pcnt
|
|
* reaches this value, the counter will be cleared to 0.
|
|
*/
|
|
#define PCNT_CNT_H_LIM_U1 0x0000FFFFU
|
|
#define PCNT_CNT_H_LIM_U1_M (PCNT_CNT_H_LIM_U1_V << PCNT_CNT_H_LIM_U1_S)
|
|
#define PCNT_CNT_H_LIM_U1_V 0x0000FFFFU
|
|
#define PCNT_CNT_H_LIM_U1_S 0
|
|
/** PCNT_CNT_L_LIM_U1 : R/W; bitpos: [31:16]; default: 0;
|
|
* This register is used to configure the thr_l_lim value for unit 1. When pcnt
|
|
* reaches this value, the counter will be cleared to 0.
|
|
*/
|
|
#define PCNT_CNT_L_LIM_U1 0x0000FFFFU
|
|
#define PCNT_CNT_L_LIM_U1_M (PCNT_CNT_L_LIM_U1_V << PCNT_CNT_L_LIM_U1_S)
|
|
#define PCNT_CNT_L_LIM_U1_V 0x0000FFFFU
|
|
#define PCNT_CNT_L_LIM_U1_S 16
|
|
|
|
/** PCNT_U2_CONF0_REG register
|
|
* Configuration register 0 for unit 2
|
|
*/
|
|
#define PCNT_U2_CONF0_REG (DR_REG_PCNT_BASE + 0x18)
|
|
/** PCNT_FILTER_THRES_U2 : R/W; bitpos: [9:0]; default: 16;
|
|
* This sets the maximum threshold, in APB_CLK cycles, for the filter.
|
|
*
|
|
* Any pulses with width less than this will be ignored when the filter is enabled.
|
|
*/
|
|
#define PCNT_FILTER_THRES_U2 0x000003FFU
|
|
#define PCNT_FILTER_THRES_U2_M (PCNT_FILTER_THRES_U2_V << PCNT_FILTER_THRES_U2_S)
|
|
#define PCNT_FILTER_THRES_U2_V 0x000003FFU
|
|
#define PCNT_FILTER_THRES_U2_S 0
|
|
/** PCNT_FILTER_EN_U2 : R/W; bitpos: [10]; default: 1;
|
|
* This is the enable bit for unit 2's input filter.
|
|
*/
|
|
#define PCNT_FILTER_EN_U2 (BIT(10))
|
|
#define PCNT_FILTER_EN_U2_M (PCNT_FILTER_EN_U2_V << PCNT_FILTER_EN_U2_S)
|
|
#define PCNT_FILTER_EN_U2_V 0x00000001U
|
|
#define PCNT_FILTER_EN_U2_S 10
|
|
/** PCNT_THR_ZERO_EN_U2 : R/W; bitpos: [11]; default: 1;
|
|
* This is the enable bit for unit 2's zero comparator.
|
|
*/
|
|
#define PCNT_THR_ZERO_EN_U2 (BIT(11))
|
|
#define PCNT_THR_ZERO_EN_U2_M (PCNT_THR_ZERO_EN_U2_V << PCNT_THR_ZERO_EN_U2_S)
|
|
#define PCNT_THR_ZERO_EN_U2_V 0x00000001U
|
|
#define PCNT_THR_ZERO_EN_U2_S 11
|
|
/** PCNT_THR_H_LIM_EN_U2 : R/W; bitpos: [12]; default: 1;
|
|
* This is the enable bit for unit 2's thr_h_lim comparator. Configures it to enable
|
|
* the high limit interrupt.
|
|
*/
|
|
#define PCNT_THR_H_LIM_EN_U2 (BIT(12))
|
|
#define PCNT_THR_H_LIM_EN_U2_M (PCNT_THR_H_LIM_EN_U2_V << PCNT_THR_H_LIM_EN_U2_S)
|
|
#define PCNT_THR_H_LIM_EN_U2_V 0x00000001U
|
|
#define PCNT_THR_H_LIM_EN_U2_S 12
|
|
/** PCNT_THR_L_LIM_EN_U2 : R/W; bitpos: [13]; default: 1;
|
|
* This is the enable bit for unit 2's thr_l_lim comparator. Configures it to enable
|
|
* the low limit interrupt.
|
|
*/
|
|
#define PCNT_THR_L_LIM_EN_U2 (BIT(13))
|
|
#define PCNT_THR_L_LIM_EN_U2_M (PCNT_THR_L_LIM_EN_U2_V << PCNT_THR_L_LIM_EN_U2_S)
|
|
#define PCNT_THR_L_LIM_EN_U2_V 0x00000001U
|
|
#define PCNT_THR_L_LIM_EN_U2_S 13
|
|
/** PCNT_THR_THRES0_EN_U2 : R/W; bitpos: [14]; default: 0;
|
|
* This is the enable bit for unit 2's thres0 comparator.
|
|
*/
|
|
#define PCNT_THR_THRES0_EN_U2 (BIT(14))
|
|
#define PCNT_THR_THRES0_EN_U2_M (PCNT_THR_THRES0_EN_U2_V << PCNT_THR_THRES0_EN_U2_S)
|
|
#define PCNT_THR_THRES0_EN_U2_V 0x00000001U
|
|
#define PCNT_THR_THRES0_EN_U2_S 14
|
|
/** PCNT_THR_THRES1_EN_U2 : R/W; bitpos: [15]; default: 0;
|
|
* This is the enable bit for unit 2's thres1 comparator.
|
|
*/
|
|
#define PCNT_THR_THRES1_EN_U2 (BIT(15))
|
|
#define PCNT_THR_THRES1_EN_U2_M (PCNT_THR_THRES1_EN_U2_V << PCNT_THR_THRES1_EN_U2_S)
|
|
#define PCNT_THR_THRES1_EN_U2_V 0x00000001U
|
|
#define PCNT_THR_THRES1_EN_U2_S 15
|
|
/** PCNT_CH0_NEG_MODE_U2 : R/W; bitpos: [17:16]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 0 detects a
|
|
* negative edge.
|
|
*
|
|
* 1: Increase the counter.2: Decrease the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH0_NEG_MODE_U2 0x00000003U
|
|
#define PCNT_CH0_NEG_MODE_U2_M (PCNT_CH0_NEG_MODE_U2_V << PCNT_CH0_NEG_MODE_U2_S)
|
|
#define PCNT_CH0_NEG_MODE_U2_V 0x00000003U
|
|
#define PCNT_CH0_NEG_MODE_U2_S 16
|
|
/** PCNT_CH0_POS_MODE_U2 : R/W; bitpos: [19:18]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 0 detects a
|
|
* positive edge.
|
|
*
|
|
* 1: Increase the counter.2: Decrease the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH0_POS_MODE_U2 0x00000003U
|
|
#define PCNT_CH0_POS_MODE_U2_M (PCNT_CH0_POS_MODE_U2_V << PCNT_CH0_POS_MODE_U2_S)
|
|
#define PCNT_CH0_POS_MODE_U2_V 0x00000003U
|
|
#define PCNT_CH0_POS_MODE_U2_S 18
|
|
/** PCNT_CH0_HCTRL_MODE_U2 : R/W; bitpos: [21:20]; default: 0;
|
|
* This register configures how the CH2_POS_MODE/CH2_NEG_MODE settings will be
|
|
* modified when the control signal is high.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH0_HCTRL_MODE_U2 0x00000003U
|
|
#define PCNT_CH0_HCTRL_MODE_U2_M (PCNT_CH0_HCTRL_MODE_U2_V << PCNT_CH0_HCTRL_MODE_U2_S)
|
|
#define PCNT_CH0_HCTRL_MODE_U2_V 0x00000003U
|
|
#define PCNT_CH0_HCTRL_MODE_U2_S 20
|
|
/** PCNT_CH0_LCTRL_MODE_U2 : R/W; bitpos: [23:22]; default: 0;
|
|
* This register configures how the CH2_POS_MODE/CH2_NEG_MODE settings will be
|
|
* modified when the control signal is low.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH0_LCTRL_MODE_U2 0x00000003U
|
|
#define PCNT_CH0_LCTRL_MODE_U2_M (PCNT_CH0_LCTRL_MODE_U2_V << PCNT_CH0_LCTRL_MODE_U2_S)
|
|
#define PCNT_CH0_LCTRL_MODE_U2_V 0x00000003U
|
|
#define PCNT_CH0_LCTRL_MODE_U2_S 22
|
|
/** PCNT_CH1_NEG_MODE_U2 : R/W; bitpos: [25:24]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 1 detects a
|
|
* negative edge.
|
|
*
|
|
* 1: Increment the counter.2: Decrement the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH1_NEG_MODE_U2 0x00000003U
|
|
#define PCNT_CH1_NEG_MODE_U2_M (PCNT_CH1_NEG_MODE_U2_V << PCNT_CH1_NEG_MODE_U2_S)
|
|
#define PCNT_CH1_NEG_MODE_U2_V 0x00000003U
|
|
#define PCNT_CH1_NEG_MODE_U2_S 24
|
|
/** PCNT_CH1_POS_MODE_U2 : R/W; bitpos: [27:26]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 1 detects a
|
|
* positive edge.
|
|
*
|
|
* 1: Increment the counter.2: Decrement the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH1_POS_MODE_U2 0x00000003U
|
|
#define PCNT_CH1_POS_MODE_U2_M (PCNT_CH1_POS_MODE_U2_V << PCNT_CH1_POS_MODE_U2_S)
|
|
#define PCNT_CH1_POS_MODE_U2_V 0x00000003U
|
|
#define PCNT_CH1_POS_MODE_U2_S 26
|
|
/** PCNT_CH1_HCTRL_MODE_U2 : R/W; bitpos: [29:28]; default: 0;
|
|
* This register configures how the CH2_POS_MODE/CH2_NEG_MODE settings will be
|
|
* modified when the control signal is high.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH1_HCTRL_MODE_U2 0x00000003U
|
|
#define PCNT_CH1_HCTRL_MODE_U2_M (PCNT_CH1_HCTRL_MODE_U2_V << PCNT_CH1_HCTRL_MODE_U2_S)
|
|
#define PCNT_CH1_HCTRL_MODE_U2_V 0x00000003U
|
|
#define PCNT_CH1_HCTRL_MODE_U2_S 28
|
|
/** PCNT_CH1_LCTRL_MODE_U2 : R/W; bitpos: [31:30]; default: 0;
|
|
* This register configures how the CH2_POS_MODE/CH2_NEG_MODE settings will be
|
|
* modified when the control signal is low.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH1_LCTRL_MODE_U2 0x00000003U
|
|
#define PCNT_CH1_LCTRL_MODE_U2_M (PCNT_CH1_LCTRL_MODE_U2_V << PCNT_CH1_LCTRL_MODE_U2_S)
|
|
#define PCNT_CH1_LCTRL_MODE_U2_V 0x00000003U
|
|
#define PCNT_CH1_LCTRL_MODE_U2_S 30
|
|
|
|
/** PCNT_U2_CONF1_REG register
|
|
* Configuration register 1 for unit 2
|
|
*/
|
|
#define PCNT_U2_CONF1_REG (DR_REG_PCNT_BASE + 0x1c)
|
|
/** PCNT_CNT_THRES0_U2 : R/W; bitpos: [15:0]; default: 0;
|
|
* This register is used to configure the thres0 value for unit 2.
|
|
*/
|
|
#define PCNT_CNT_THRES0_U2 0x0000FFFFU
|
|
#define PCNT_CNT_THRES0_U2_M (PCNT_CNT_THRES0_U2_V << PCNT_CNT_THRES0_U2_S)
|
|
#define PCNT_CNT_THRES0_U2_V 0x0000FFFFU
|
|
#define PCNT_CNT_THRES0_U2_S 0
|
|
/** PCNT_CNT_THRES1_U2 : R/W; bitpos: [31:16]; default: 0;
|
|
* This register is used to configure the thres1 value for unit 2.
|
|
*/
|
|
#define PCNT_CNT_THRES1_U2 0x0000FFFFU
|
|
#define PCNT_CNT_THRES1_U2_M (PCNT_CNT_THRES1_U2_V << PCNT_CNT_THRES1_U2_S)
|
|
#define PCNT_CNT_THRES1_U2_V 0x0000FFFFU
|
|
#define PCNT_CNT_THRES1_U2_S 16
|
|
|
|
/** PCNT_U2_CONF2_REG register
|
|
* Configuration register 2 for unit 2
|
|
*/
|
|
#define PCNT_U2_CONF2_REG (DR_REG_PCNT_BASE + 0x20)
|
|
/** PCNT_CNT_H_LIM_U2 : R/W; bitpos: [15:0]; default: 0;
|
|
* This register is used to configure the thr_h_lim value for unit 2. When pcnt
|
|
* reaches this value, the counter will be cleared to 0.
|
|
*/
|
|
#define PCNT_CNT_H_LIM_U2 0x0000FFFFU
|
|
#define PCNT_CNT_H_LIM_U2_M (PCNT_CNT_H_LIM_U2_V << PCNT_CNT_H_LIM_U2_S)
|
|
#define PCNT_CNT_H_LIM_U2_V 0x0000FFFFU
|
|
#define PCNT_CNT_H_LIM_U2_S 0
|
|
/** PCNT_CNT_L_LIM_U2 : R/W; bitpos: [31:16]; default: 0;
|
|
* This register is used to configure the thr_l_lim value for unit 2. When pcnt
|
|
* reaches this value, the counter will be cleared to 0.
|
|
*/
|
|
#define PCNT_CNT_L_LIM_U2 0x0000FFFFU
|
|
#define PCNT_CNT_L_LIM_U2_M (PCNT_CNT_L_LIM_U2_V << PCNT_CNT_L_LIM_U2_S)
|
|
#define PCNT_CNT_L_LIM_U2_V 0x0000FFFFU
|
|
#define PCNT_CNT_L_LIM_U2_S 16
|
|
|
|
/** PCNT_U3_CONF0_REG register
|
|
* Configuration register 0 for unit 3
|
|
*/
|
|
#define PCNT_U3_CONF0_REG (DR_REG_PCNT_BASE + 0x24)
|
|
/** PCNT_FILTER_THRES_U3 : R/W; bitpos: [9:0]; default: 16;
|
|
* This sets the maximum threshold, in APB_CLK cycles, for the filter.
|
|
*
|
|
* Any pulses with width less than this will be ignored when the filter is enabled.
|
|
*/
|
|
#define PCNT_FILTER_THRES_U3 0x000003FFU
|
|
#define PCNT_FILTER_THRES_U3_M (PCNT_FILTER_THRES_U3_V << PCNT_FILTER_THRES_U3_S)
|
|
#define PCNT_FILTER_THRES_U3_V 0x000003FFU
|
|
#define PCNT_FILTER_THRES_U3_S 0
|
|
/** PCNT_FILTER_EN_U3 : R/W; bitpos: [10]; default: 1;
|
|
* This is the enable bit for unit 3's input filter.
|
|
*/
|
|
#define PCNT_FILTER_EN_U3 (BIT(10))
|
|
#define PCNT_FILTER_EN_U3_M (PCNT_FILTER_EN_U3_V << PCNT_FILTER_EN_U3_S)
|
|
#define PCNT_FILTER_EN_U3_V 0x00000001U
|
|
#define PCNT_FILTER_EN_U3_S 10
|
|
/** PCNT_THR_ZERO_EN_U3 : R/W; bitpos: [11]; default: 1;
|
|
* This is the enable bit for unit 3's zero comparator.
|
|
*/
|
|
#define PCNT_THR_ZERO_EN_U3 (BIT(11))
|
|
#define PCNT_THR_ZERO_EN_U3_M (PCNT_THR_ZERO_EN_U3_V << PCNT_THR_ZERO_EN_U3_S)
|
|
#define PCNT_THR_ZERO_EN_U3_V 0x00000001U
|
|
#define PCNT_THR_ZERO_EN_U3_S 11
|
|
/** PCNT_THR_H_LIM_EN_U3 : R/W; bitpos: [12]; default: 1;
|
|
* This is the enable bit for unit 3's thr_h_lim comparator. Configures it to enable
|
|
* the high limit interrupt.
|
|
*/
|
|
#define PCNT_THR_H_LIM_EN_U3 (BIT(12))
|
|
#define PCNT_THR_H_LIM_EN_U3_M (PCNT_THR_H_LIM_EN_U3_V << PCNT_THR_H_LIM_EN_U3_S)
|
|
#define PCNT_THR_H_LIM_EN_U3_V 0x00000001U
|
|
#define PCNT_THR_H_LIM_EN_U3_S 12
|
|
/** PCNT_THR_L_LIM_EN_U3 : R/W; bitpos: [13]; default: 1;
|
|
* This is the enable bit for unit 3's thr_l_lim comparator. Configures it to enable
|
|
* the low limit interrupt.
|
|
*/
|
|
#define PCNT_THR_L_LIM_EN_U3 (BIT(13))
|
|
#define PCNT_THR_L_LIM_EN_U3_M (PCNT_THR_L_LIM_EN_U3_V << PCNT_THR_L_LIM_EN_U3_S)
|
|
#define PCNT_THR_L_LIM_EN_U3_V 0x00000001U
|
|
#define PCNT_THR_L_LIM_EN_U3_S 13
|
|
/** PCNT_THR_THRES0_EN_U3 : R/W; bitpos: [14]; default: 0;
|
|
* This is the enable bit for unit 3's thres0 comparator.
|
|
*/
|
|
#define PCNT_THR_THRES0_EN_U3 (BIT(14))
|
|
#define PCNT_THR_THRES0_EN_U3_M (PCNT_THR_THRES0_EN_U3_V << PCNT_THR_THRES0_EN_U3_S)
|
|
#define PCNT_THR_THRES0_EN_U3_V 0x00000001U
|
|
#define PCNT_THR_THRES0_EN_U3_S 14
|
|
/** PCNT_THR_THRES1_EN_U3 : R/W; bitpos: [15]; default: 0;
|
|
* This is the enable bit for unit 3's thres1 comparator.
|
|
*/
|
|
#define PCNT_THR_THRES1_EN_U3 (BIT(15))
|
|
#define PCNT_THR_THRES1_EN_U3_M (PCNT_THR_THRES1_EN_U3_V << PCNT_THR_THRES1_EN_U3_S)
|
|
#define PCNT_THR_THRES1_EN_U3_V 0x00000001U
|
|
#define PCNT_THR_THRES1_EN_U3_S 15
|
|
/** PCNT_CH0_NEG_MODE_U3 : R/W; bitpos: [17:16]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 0 detects a
|
|
* negative edge.
|
|
*
|
|
* 1: Increase the counter.2: Decrease the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH0_NEG_MODE_U3 0x00000003U
|
|
#define PCNT_CH0_NEG_MODE_U3_M (PCNT_CH0_NEG_MODE_U3_V << PCNT_CH0_NEG_MODE_U3_S)
|
|
#define PCNT_CH0_NEG_MODE_U3_V 0x00000003U
|
|
#define PCNT_CH0_NEG_MODE_U3_S 16
|
|
/** PCNT_CH0_POS_MODE_U3 : R/W; bitpos: [19:18]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 0 detects a
|
|
* positive edge.
|
|
*
|
|
* 1: Increase the counter.2: Decrease the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH0_POS_MODE_U3 0x00000003U
|
|
#define PCNT_CH0_POS_MODE_U3_M (PCNT_CH0_POS_MODE_U3_V << PCNT_CH0_POS_MODE_U3_S)
|
|
#define PCNT_CH0_POS_MODE_U3_V 0x00000003U
|
|
#define PCNT_CH0_POS_MODE_U3_S 18
|
|
/** PCNT_CH0_HCTRL_MODE_U3 : R/W; bitpos: [21:20]; default: 0;
|
|
* This register configures how the CH3_POS_MODE/CH3_NEG_MODE settings will be
|
|
* modified when the control signal is high.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH0_HCTRL_MODE_U3 0x00000003U
|
|
#define PCNT_CH0_HCTRL_MODE_U3_M (PCNT_CH0_HCTRL_MODE_U3_V << PCNT_CH0_HCTRL_MODE_U3_S)
|
|
#define PCNT_CH0_HCTRL_MODE_U3_V 0x00000003U
|
|
#define PCNT_CH0_HCTRL_MODE_U3_S 20
|
|
/** PCNT_CH0_LCTRL_MODE_U3 : R/W; bitpos: [23:22]; default: 0;
|
|
* This register configures how the CH3_POS_MODE/CH3_NEG_MODE settings will be
|
|
* modified when the control signal is low.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH0_LCTRL_MODE_U3 0x00000003U
|
|
#define PCNT_CH0_LCTRL_MODE_U3_M (PCNT_CH0_LCTRL_MODE_U3_V << PCNT_CH0_LCTRL_MODE_U3_S)
|
|
#define PCNT_CH0_LCTRL_MODE_U3_V 0x00000003U
|
|
#define PCNT_CH0_LCTRL_MODE_U3_S 22
|
|
/** PCNT_CH1_NEG_MODE_U3 : R/W; bitpos: [25:24]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 1 detects a
|
|
* negative edge.
|
|
*
|
|
* 1: Increment the counter.2: Decrement the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH1_NEG_MODE_U3 0x00000003U
|
|
#define PCNT_CH1_NEG_MODE_U3_M (PCNT_CH1_NEG_MODE_U3_V << PCNT_CH1_NEG_MODE_U3_S)
|
|
#define PCNT_CH1_NEG_MODE_U3_V 0x00000003U
|
|
#define PCNT_CH1_NEG_MODE_U3_S 24
|
|
/** PCNT_CH1_POS_MODE_U3 : R/W; bitpos: [27:26]; default: 0;
|
|
* This register sets the behavior when the signal input of channel 1 detects a
|
|
* positive edge.
|
|
*
|
|
* 1: Increment the counter.2: Decrement the counter.0, 3: No effect on counter
|
|
*/
|
|
#define PCNT_CH1_POS_MODE_U3 0x00000003U
|
|
#define PCNT_CH1_POS_MODE_U3_M (PCNT_CH1_POS_MODE_U3_V << PCNT_CH1_POS_MODE_U3_S)
|
|
#define PCNT_CH1_POS_MODE_U3_V 0x00000003U
|
|
#define PCNT_CH1_POS_MODE_U3_S 26
|
|
/** PCNT_CH1_HCTRL_MODE_U3 : R/W; bitpos: [29:28]; default: 0;
|
|
* This register configures how the CH3_POS_MODE/CH3_NEG_MODE settings will be
|
|
* modified when the control signal is high.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH1_HCTRL_MODE_U3 0x00000003U
|
|
#define PCNT_CH1_HCTRL_MODE_U3_M (PCNT_CH1_HCTRL_MODE_U3_V << PCNT_CH1_HCTRL_MODE_U3_S)
|
|
#define PCNT_CH1_HCTRL_MODE_U3_V 0x00000003U
|
|
#define PCNT_CH1_HCTRL_MODE_U3_S 28
|
|
/** PCNT_CH1_LCTRL_MODE_U3 : R/W; bitpos: [31:30]; default: 0;
|
|
* This register configures how the CH3_POS_MODE/CH3_NEG_MODE settings will be
|
|
* modified when the control signal is low.
|
|
*
|
|
* 0: No modification.1: Invert behavior (increase -> decrease, decrease ->
|
|
* increase).2, 3: Inhibit counter modification
|
|
*/
|
|
#define PCNT_CH1_LCTRL_MODE_U3 0x00000003U
|
|
#define PCNT_CH1_LCTRL_MODE_U3_M (PCNT_CH1_LCTRL_MODE_U3_V << PCNT_CH1_LCTRL_MODE_U3_S)
|
|
#define PCNT_CH1_LCTRL_MODE_U3_V 0x00000003U
|
|
#define PCNT_CH1_LCTRL_MODE_U3_S 30
|
|
|
|
/** PCNT_U3_CONF1_REG register
|
|
* Configuration register 1 for unit 3
|
|
*/
|
|
#define PCNT_U3_CONF1_REG (DR_REG_PCNT_BASE + 0x28)
|
|
/** PCNT_CNT_THRES0_U3 : R/W; bitpos: [15:0]; default: 0;
|
|
* This register is used to configure the thres0 value for unit 3.
|
|
*/
|
|
#define PCNT_CNT_THRES0_U3 0x0000FFFFU
|
|
#define PCNT_CNT_THRES0_U3_M (PCNT_CNT_THRES0_U3_V << PCNT_CNT_THRES0_U3_S)
|
|
#define PCNT_CNT_THRES0_U3_V 0x0000FFFFU
|
|
#define PCNT_CNT_THRES0_U3_S 0
|
|
/** PCNT_CNT_THRES1_U3 : R/W; bitpos: [31:16]; default: 0;
|
|
* This register is used to configure the thres1 value for unit 3.
|
|
*/
|
|
#define PCNT_CNT_THRES1_U3 0x0000FFFFU
|
|
#define PCNT_CNT_THRES1_U3_M (PCNT_CNT_THRES1_U3_V << PCNT_CNT_THRES1_U3_S)
|
|
#define PCNT_CNT_THRES1_U3_V 0x0000FFFFU
|
|
#define PCNT_CNT_THRES1_U3_S 16
|
|
|
|
/** PCNT_U3_CONF2_REG register
|
|
* Configuration register 2 for unit 3
|
|
*/
|
|
#define PCNT_U3_CONF2_REG (DR_REG_PCNT_BASE + 0x2c)
|
|
/** PCNT_CNT_H_LIM_U3 : R/W; bitpos: [15:0]; default: 0;
|
|
* This register is used to configure the thr_h_lim value for unit 3. When pcnt
|
|
* reaches this value, the counter will be cleared to 0.
|
|
*/
|
|
#define PCNT_CNT_H_LIM_U3 0x0000FFFFU
|
|
#define PCNT_CNT_H_LIM_U3_M (PCNT_CNT_H_LIM_U3_V << PCNT_CNT_H_LIM_U3_S)
|
|
#define PCNT_CNT_H_LIM_U3_V 0x0000FFFFU
|
|
#define PCNT_CNT_H_LIM_U3_S 0
|
|
/** PCNT_CNT_L_LIM_U3 : R/W; bitpos: [31:16]; default: 0;
|
|
* This register is used to configure the thr_l_lim value for unit 3. When pcnt
|
|
* reaches this value, the counter will be cleared to 0.
|
|
*/
|
|
#define PCNT_CNT_L_LIM_U3 0x0000FFFFU
|
|
#define PCNT_CNT_L_LIM_U3_M (PCNT_CNT_L_LIM_U3_V << PCNT_CNT_L_LIM_U3_S)
|
|
#define PCNT_CNT_L_LIM_U3_V 0x0000FFFFU
|
|
#define PCNT_CNT_L_LIM_U3_S 16
|
|
|
|
/** PCNT_U0_CNT_REG register
|
|
* Counter value for unit 0
|
|
*/
|
|
#define PCNT_U0_CNT_REG (DR_REG_PCNT_BASE + 0x30)
|
|
/** PCNT_PULSE_CNT_U0 : RO; bitpos: [15:0]; default: 0;
|
|
* This register stores the current pulse count value for unit 0.
|
|
*/
|
|
#define PCNT_PULSE_CNT_U0 0x0000FFFFU
|
|
#define PCNT_PULSE_CNT_U0_M (PCNT_PULSE_CNT_U0_V << PCNT_PULSE_CNT_U0_S)
|
|
#define PCNT_PULSE_CNT_U0_V 0x0000FFFFU
|
|
#define PCNT_PULSE_CNT_U0_S 0
|
|
|
|
/** PCNT_U1_CNT_REG register
|
|
* Counter value for unit 1
|
|
*/
|
|
#define PCNT_U1_CNT_REG (DR_REG_PCNT_BASE + 0x34)
|
|
/** PCNT_PULSE_CNT_U1 : RO; bitpos: [15:0]; default: 0;
|
|
* This register stores the current pulse count value for unit 1.
|
|
*/
|
|
#define PCNT_PULSE_CNT_U1 0x0000FFFFU
|
|
#define PCNT_PULSE_CNT_U1_M (PCNT_PULSE_CNT_U1_V << PCNT_PULSE_CNT_U1_S)
|
|
#define PCNT_PULSE_CNT_U1_V 0x0000FFFFU
|
|
#define PCNT_PULSE_CNT_U1_S 0
|
|
|
|
/** PCNT_U2_CNT_REG register
|
|
* Counter value for unit 2
|
|
*/
|
|
#define PCNT_U2_CNT_REG (DR_REG_PCNT_BASE + 0x38)
|
|
/** PCNT_PULSE_CNT_U2 : RO; bitpos: [15:0]; default: 0;
|
|
* This register stores the current pulse count value for unit 2.
|
|
*/
|
|
#define PCNT_PULSE_CNT_U2 0x0000FFFFU
|
|
#define PCNT_PULSE_CNT_U2_M (PCNT_PULSE_CNT_U2_V << PCNT_PULSE_CNT_U2_S)
|
|
#define PCNT_PULSE_CNT_U2_V 0x0000FFFFU
|
|
#define PCNT_PULSE_CNT_U2_S 0
|
|
|
|
/** PCNT_U3_CNT_REG register
|
|
* Counter value for unit 3
|
|
*/
|
|
#define PCNT_U3_CNT_REG (DR_REG_PCNT_BASE + 0x3c)
|
|
/** PCNT_PULSE_CNT_U3 : RO; bitpos: [15:0]; default: 0;
|
|
* This register stores the current pulse count value for unit 3.
|
|
*/
|
|
#define PCNT_PULSE_CNT_U3 0x0000FFFFU
|
|
#define PCNT_PULSE_CNT_U3_M (PCNT_PULSE_CNT_U3_V << PCNT_PULSE_CNT_U3_S)
|
|
#define PCNT_PULSE_CNT_U3_V 0x0000FFFFU
|
|
#define PCNT_PULSE_CNT_U3_S 0
|
|
|
|
/** PCNT_INT_RAW_REG register
|
|
* Interrupt raw status register
|
|
*/
|
|
#define PCNT_INT_RAW_REG (DR_REG_PCNT_BASE + 0x40)
|
|
/** PCNT_CNT_THR_EVENT_U0_INT_RAW : R/WTC/SS; bitpos: [0]; default: 0;
|
|
* The raw interrupt status bit for the PCNT_CNT_THR_EVENT_U0_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_RAW (BIT(0))
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_RAW_M (PCNT_CNT_THR_EVENT_U0_INT_RAW_V << PCNT_CNT_THR_EVENT_U0_INT_RAW_S)
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_RAW_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_RAW_S 0
|
|
/** PCNT_CNT_THR_EVENT_U1_INT_RAW : R/WTC/SS; bitpos: [1]; default: 0;
|
|
* The raw interrupt status bit for the PCNT_CNT_THR_EVENT_U1_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_RAW (BIT(1))
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_RAW_M (PCNT_CNT_THR_EVENT_U1_INT_RAW_V << PCNT_CNT_THR_EVENT_U1_INT_RAW_S)
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_RAW_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_RAW_S 1
|
|
/** PCNT_CNT_THR_EVENT_U2_INT_RAW : R/WTC/SS; bitpos: [2]; default: 0;
|
|
* The raw interrupt status bit for the PCNT_CNT_THR_EVENT_U2_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_RAW (BIT(2))
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_RAW_M (PCNT_CNT_THR_EVENT_U2_INT_RAW_V << PCNT_CNT_THR_EVENT_U2_INT_RAW_S)
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_RAW_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_RAW_S 2
|
|
/** PCNT_CNT_THR_EVENT_U3_INT_RAW : R/WTC/SS; bitpos: [3]; default: 0;
|
|
* The raw interrupt status bit for the PCNT_CNT_THR_EVENT_U3_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_RAW (BIT(3))
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_RAW_M (PCNT_CNT_THR_EVENT_U3_INT_RAW_V << PCNT_CNT_THR_EVENT_U3_INT_RAW_S)
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_RAW_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_RAW_S 3
|
|
|
|
/** PCNT_INT_ST_REG register
|
|
* Interrupt status register
|
|
*/
|
|
#define PCNT_INT_ST_REG (DR_REG_PCNT_BASE + 0x44)
|
|
/** PCNT_CNT_THR_EVENT_U0_INT_ST : RO; bitpos: [0]; default: 0;
|
|
* The masked interrupt status bit for the PCNT_CNT_THR_EVENT_U0_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_ST (BIT(0))
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_ST_M (PCNT_CNT_THR_EVENT_U0_INT_ST_V << PCNT_CNT_THR_EVENT_U0_INT_ST_S)
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_ST_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_ST_S 0
|
|
/** PCNT_CNT_THR_EVENT_U1_INT_ST : RO; bitpos: [1]; default: 0;
|
|
* The masked interrupt status bit for the PCNT_CNT_THR_EVENT_U1_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_ST (BIT(1))
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_ST_M (PCNT_CNT_THR_EVENT_U1_INT_ST_V << PCNT_CNT_THR_EVENT_U1_INT_ST_S)
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_ST_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_ST_S 1
|
|
/** PCNT_CNT_THR_EVENT_U2_INT_ST : RO; bitpos: [2]; default: 0;
|
|
* The masked interrupt status bit for the PCNT_CNT_THR_EVENT_U2_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_ST (BIT(2))
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_ST_M (PCNT_CNT_THR_EVENT_U2_INT_ST_V << PCNT_CNT_THR_EVENT_U2_INT_ST_S)
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_ST_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_ST_S 2
|
|
/** PCNT_CNT_THR_EVENT_U3_INT_ST : RO; bitpos: [3]; default: 0;
|
|
* The masked interrupt status bit for the PCNT_CNT_THR_EVENT_U3_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_ST (BIT(3))
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_ST_M (PCNT_CNT_THR_EVENT_U3_INT_ST_V << PCNT_CNT_THR_EVENT_U3_INT_ST_S)
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_ST_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_ST_S 3
|
|
|
|
/** PCNT_INT_ENA_REG register
|
|
* Interrupt enable register
|
|
*/
|
|
#define PCNT_INT_ENA_REG (DR_REG_PCNT_BASE + 0x48)
|
|
/** PCNT_CNT_THR_EVENT_U0_INT_ENA : R/W; bitpos: [0]; default: 0;
|
|
* The interrupt enable bit for the PCNT_CNT_THR_EVENT_U0_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_ENA (BIT(0))
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_ENA_M (PCNT_CNT_THR_EVENT_U0_INT_ENA_V << PCNT_CNT_THR_EVENT_U0_INT_ENA_S)
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_ENA_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_ENA_S 0
|
|
/** PCNT_CNT_THR_EVENT_U1_INT_ENA : R/W; bitpos: [1]; default: 0;
|
|
* The interrupt enable bit for the PCNT_CNT_THR_EVENT_U1_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_ENA (BIT(1))
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_ENA_M (PCNT_CNT_THR_EVENT_U1_INT_ENA_V << PCNT_CNT_THR_EVENT_U1_INT_ENA_S)
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_ENA_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_ENA_S 1
|
|
/** PCNT_CNT_THR_EVENT_U2_INT_ENA : R/W; bitpos: [2]; default: 0;
|
|
* The interrupt enable bit for the PCNT_CNT_THR_EVENT_U2_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_ENA (BIT(2))
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_ENA_M (PCNT_CNT_THR_EVENT_U2_INT_ENA_V << PCNT_CNT_THR_EVENT_U2_INT_ENA_S)
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_ENA_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_ENA_S 2
|
|
/** PCNT_CNT_THR_EVENT_U3_INT_ENA : R/W; bitpos: [3]; default: 0;
|
|
* The interrupt enable bit for the PCNT_CNT_THR_EVENT_U3_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_ENA (BIT(3))
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_ENA_M (PCNT_CNT_THR_EVENT_U3_INT_ENA_V << PCNT_CNT_THR_EVENT_U3_INT_ENA_S)
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_ENA_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_ENA_S 3
|
|
|
|
/** PCNT_INT_CLR_REG register
|
|
* Interrupt clear register
|
|
*/
|
|
#define PCNT_INT_CLR_REG (DR_REG_PCNT_BASE + 0x4c)
|
|
/** PCNT_CNT_THR_EVENT_U0_INT_CLR : WT; bitpos: [0]; default: 0;
|
|
* Set this bit to clear the PCNT_CNT_THR_EVENT_U0_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_CLR (BIT(0))
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_CLR_M (PCNT_CNT_THR_EVENT_U0_INT_CLR_V << PCNT_CNT_THR_EVENT_U0_INT_CLR_S)
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_CLR_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U0_INT_CLR_S 0
|
|
/** PCNT_CNT_THR_EVENT_U1_INT_CLR : WT; bitpos: [1]; default: 0;
|
|
* Set this bit to clear the PCNT_CNT_THR_EVENT_U1_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_CLR (BIT(1))
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_CLR_M (PCNT_CNT_THR_EVENT_U1_INT_CLR_V << PCNT_CNT_THR_EVENT_U1_INT_CLR_S)
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_CLR_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U1_INT_CLR_S 1
|
|
/** PCNT_CNT_THR_EVENT_U2_INT_CLR : WT; bitpos: [2]; default: 0;
|
|
* Set this bit to clear the PCNT_CNT_THR_EVENT_U2_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_CLR (BIT(2))
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_CLR_M (PCNT_CNT_THR_EVENT_U2_INT_CLR_V << PCNT_CNT_THR_EVENT_U2_INT_CLR_S)
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_CLR_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U2_INT_CLR_S 2
|
|
/** PCNT_CNT_THR_EVENT_U3_INT_CLR : WT; bitpos: [3]; default: 0;
|
|
* Set this bit to clear the PCNT_CNT_THR_EVENT_U3_INT interrupt.
|
|
*/
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_CLR (BIT(3))
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_CLR_M (PCNT_CNT_THR_EVENT_U3_INT_CLR_V << PCNT_CNT_THR_EVENT_U3_INT_CLR_S)
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_CLR_V 0x00000001U
|
|
#define PCNT_CNT_THR_EVENT_U3_INT_CLR_S 3
|
|
|
|
/** PCNT_U0_STATUS_REG register
|
|
* PNCT UNIT0 status register
|
|
*/
|
|
#define PCNT_U0_STATUS_REG (DR_REG_PCNT_BASE + 0x50)
|
|
/** PCNT_CNT_THR_ZERO_MODE_U0 : RO; bitpos: [1:0]; default: 0;
|
|
* The pulse counter status of PCNT_U0 corresponding to 0. 0: pulse counter decreases
|
|
* from positive to 0. 1: pulse counter increases from negative to 0. 2: pulse counter
|
|
* is negative. 3: pulse counter is positive.
|
|
*/
|
|
#define PCNT_CNT_THR_ZERO_MODE_U0 0x00000003U
|
|
#define PCNT_CNT_THR_ZERO_MODE_U0_M (PCNT_CNT_THR_ZERO_MODE_U0_V << PCNT_CNT_THR_ZERO_MODE_U0_S)
|
|
#define PCNT_CNT_THR_ZERO_MODE_U0_V 0x00000003U
|
|
#define PCNT_CNT_THR_ZERO_MODE_U0_S 0
|
|
/** PCNT_CNT_THR_THRES1_LAT_U0 : RO; bitpos: [2]; default: 0;
|
|
* The latched value of thres1 event of PCNT_U0 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thres1 and thres1 event is valid. 0:
|
|
* others
|
|
*/
|
|
#define PCNT_CNT_THR_THRES1_LAT_U0 (BIT(2))
|
|
#define PCNT_CNT_THR_THRES1_LAT_U0_M (PCNT_CNT_THR_THRES1_LAT_U0_V << PCNT_CNT_THR_THRES1_LAT_U0_S)
|
|
#define PCNT_CNT_THR_THRES1_LAT_U0_V 0x00000001U
|
|
#define PCNT_CNT_THR_THRES1_LAT_U0_S 2
|
|
/** PCNT_CNT_THR_THRES0_LAT_U0 : RO; bitpos: [3]; default: 0;
|
|
* The latched value of thres0 event of PCNT_U0 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thres0 and thres0 event is valid. 0:
|
|
* others
|
|
*/
|
|
#define PCNT_CNT_THR_THRES0_LAT_U0 (BIT(3))
|
|
#define PCNT_CNT_THR_THRES0_LAT_U0_M (PCNT_CNT_THR_THRES0_LAT_U0_V << PCNT_CNT_THR_THRES0_LAT_U0_S)
|
|
#define PCNT_CNT_THR_THRES0_LAT_U0_V 0x00000001U
|
|
#define PCNT_CNT_THR_THRES0_LAT_U0_S 3
|
|
/** PCNT_CNT_THR_L_LIM_LAT_U0 : RO; bitpos: [4]; default: 0;
|
|
* The latched value of low limit event of PCNT_U0 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thr_l_lim and low limit event is
|
|
* valid. 0: others
|
|
*/
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U0 (BIT(4))
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U0_M (PCNT_CNT_THR_L_LIM_LAT_U0_V << PCNT_CNT_THR_L_LIM_LAT_U0_S)
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U0_V 0x00000001U
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U0_S 4
|
|
/** PCNT_CNT_THR_H_LIM_LAT_U0 : RO; bitpos: [5]; default: 0;
|
|
* The latched value of high limit event of PCNT_U0 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thr_h_lim and high limit event is
|
|
* valid. 0: others
|
|
*/
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U0 (BIT(5))
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U0_M (PCNT_CNT_THR_H_LIM_LAT_U0_V << PCNT_CNT_THR_H_LIM_LAT_U0_S)
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U0_V 0x00000001U
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U0_S 5
|
|
/** PCNT_CNT_THR_ZERO_LAT_U0 : RO; bitpos: [6]; default: 0;
|
|
* The latched value of zero threshold event of PCNT_U0 when threshold event interrupt
|
|
* is valid. 1: the current pulse counter equals to 0 and zero threshold event is
|
|
* valid. 0: others
|
|
*/
|
|
#define PCNT_CNT_THR_ZERO_LAT_U0 (BIT(6))
|
|
#define PCNT_CNT_THR_ZERO_LAT_U0_M (PCNT_CNT_THR_ZERO_LAT_U0_V << PCNT_CNT_THR_ZERO_LAT_U0_S)
|
|
#define PCNT_CNT_THR_ZERO_LAT_U0_V 0x00000001U
|
|
#define PCNT_CNT_THR_ZERO_LAT_U0_S 6
|
|
|
|
/** PCNT_U1_STATUS_REG register
|
|
* PNCT UNIT1 status register
|
|
*/
|
|
#define PCNT_U1_STATUS_REG (DR_REG_PCNT_BASE + 0x54)
|
|
/** PCNT_CNT_THR_ZERO_MODE_U1 : RO; bitpos: [1:0]; default: 0;
|
|
* The pulse counter status of PCNT_U1 corresponding to 0. 0: pulse counter decreases
|
|
* from positive to 0. 1: pulse counter increases from negative to 0. 2: pulse counter
|
|
* is negative. 3: pulse counter is positive.
|
|
*/
|
|
#define PCNT_CNT_THR_ZERO_MODE_U1 0x00000003U
|
|
#define PCNT_CNT_THR_ZERO_MODE_U1_M (PCNT_CNT_THR_ZERO_MODE_U1_V << PCNT_CNT_THR_ZERO_MODE_U1_S)
|
|
#define PCNT_CNT_THR_ZERO_MODE_U1_V 0x00000003U
|
|
#define PCNT_CNT_THR_ZERO_MODE_U1_S 0
|
|
/** PCNT_CNT_THR_THRES1_LAT_U1 : RO; bitpos: [2]; default: 0;
|
|
* The latched value of thres1 event of PCNT_U1 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thres1 and thres1 event is valid. 0:
|
|
* others
|
|
*/
|
|
#define PCNT_CNT_THR_THRES1_LAT_U1 (BIT(2))
|
|
#define PCNT_CNT_THR_THRES1_LAT_U1_M (PCNT_CNT_THR_THRES1_LAT_U1_V << PCNT_CNT_THR_THRES1_LAT_U1_S)
|
|
#define PCNT_CNT_THR_THRES1_LAT_U1_V 0x00000001U
|
|
#define PCNT_CNT_THR_THRES1_LAT_U1_S 2
|
|
/** PCNT_CNT_THR_THRES0_LAT_U1 : RO; bitpos: [3]; default: 0;
|
|
* The latched value of thres0 event of PCNT_U1 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thres0 and thres0 event is valid. 0:
|
|
* others
|
|
*/
|
|
#define PCNT_CNT_THR_THRES0_LAT_U1 (BIT(3))
|
|
#define PCNT_CNT_THR_THRES0_LAT_U1_M (PCNT_CNT_THR_THRES0_LAT_U1_V << PCNT_CNT_THR_THRES0_LAT_U1_S)
|
|
#define PCNT_CNT_THR_THRES0_LAT_U1_V 0x00000001U
|
|
#define PCNT_CNT_THR_THRES0_LAT_U1_S 3
|
|
/** PCNT_CNT_THR_L_LIM_LAT_U1 : RO; bitpos: [4]; default: 0;
|
|
* The latched value of low limit event of PCNT_U1 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thr_l_lim and low limit event is
|
|
* valid. 0: others
|
|
*/
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U1 (BIT(4))
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U1_M (PCNT_CNT_THR_L_LIM_LAT_U1_V << PCNT_CNT_THR_L_LIM_LAT_U1_S)
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U1_V 0x00000001U
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U1_S 4
|
|
/** PCNT_CNT_THR_H_LIM_LAT_U1 : RO; bitpos: [5]; default: 0;
|
|
* The latched value of high limit event of PCNT_U1 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thr_h_lim and high limit event is
|
|
* valid. 0: others
|
|
*/
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U1 (BIT(5))
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U1_M (PCNT_CNT_THR_H_LIM_LAT_U1_V << PCNT_CNT_THR_H_LIM_LAT_U1_S)
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U1_V 0x00000001U
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U1_S 5
|
|
/** PCNT_CNT_THR_ZERO_LAT_U1 : RO; bitpos: [6]; default: 0;
|
|
* The latched value of zero threshold event of PCNT_U1 when threshold event interrupt
|
|
* is valid. 1: the current pulse counter equals to 0 and zero threshold event is
|
|
* valid. 0: others
|
|
*/
|
|
#define PCNT_CNT_THR_ZERO_LAT_U1 (BIT(6))
|
|
#define PCNT_CNT_THR_ZERO_LAT_U1_M (PCNT_CNT_THR_ZERO_LAT_U1_V << PCNT_CNT_THR_ZERO_LAT_U1_S)
|
|
#define PCNT_CNT_THR_ZERO_LAT_U1_V 0x00000001U
|
|
#define PCNT_CNT_THR_ZERO_LAT_U1_S 6
|
|
|
|
/** PCNT_U2_STATUS_REG register
|
|
* PNCT UNIT2 status register
|
|
*/
|
|
#define PCNT_U2_STATUS_REG (DR_REG_PCNT_BASE + 0x58)
|
|
/** PCNT_CNT_THR_ZERO_MODE_U2 : RO; bitpos: [1:0]; default: 0;
|
|
* The pulse counter status of PCNT_U2 corresponding to 0. 0: pulse counter decreases
|
|
* from positive to 0. 1: pulse counter increases from negative to 0. 2: pulse counter
|
|
* is negative. 3: pulse counter is positive.
|
|
*/
|
|
#define PCNT_CNT_THR_ZERO_MODE_U2 0x00000003U
|
|
#define PCNT_CNT_THR_ZERO_MODE_U2_M (PCNT_CNT_THR_ZERO_MODE_U2_V << PCNT_CNT_THR_ZERO_MODE_U2_S)
|
|
#define PCNT_CNT_THR_ZERO_MODE_U2_V 0x00000003U
|
|
#define PCNT_CNT_THR_ZERO_MODE_U2_S 0
|
|
/** PCNT_CNT_THR_THRES1_LAT_U2 : RO; bitpos: [2]; default: 0;
|
|
* The latched value of thres1 event of PCNT_U2 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thres1 and thres1 event is valid. 0:
|
|
* others
|
|
*/
|
|
#define PCNT_CNT_THR_THRES1_LAT_U2 (BIT(2))
|
|
#define PCNT_CNT_THR_THRES1_LAT_U2_M (PCNT_CNT_THR_THRES1_LAT_U2_V << PCNT_CNT_THR_THRES1_LAT_U2_S)
|
|
#define PCNT_CNT_THR_THRES1_LAT_U2_V 0x00000001U
|
|
#define PCNT_CNT_THR_THRES1_LAT_U2_S 2
|
|
/** PCNT_CNT_THR_THRES0_LAT_U2 : RO; bitpos: [3]; default: 0;
|
|
* The latched value of thres0 event of PCNT_U2 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thres0 and thres0 event is valid. 0:
|
|
* others
|
|
*/
|
|
#define PCNT_CNT_THR_THRES0_LAT_U2 (BIT(3))
|
|
#define PCNT_CNT_THR_THRES0_LAT_U2_M (PCNT_CNT_THR_THRES0_LAT_U2_V << PCNT_CNT_THR_THRES0_LAT_U2_S)
|
|
#define PCNT_CNT_THR_THRES0_LAT_U2_V 0x00000001U
|
|
#define PCNT_CNT_THR_THRES0_LAT_U2_S 3
|
|
/** PCNT_CNT_THR_L_LIM_LAT_U2 : RO; bitpos: [4]; default: 0;
|
|
* The latched value of low limit event of PCNT_U2 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thr_l_lim and low limit event is
|
|
* valid. 0: others
|
|
*/
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U2 (BIT(4))
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U2_M (PCNT_CNT_THR_L_LIM_LAT_U2_V << PCNT_CNT_THR_L_LIM_LAT_U2_S)
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U2_V 0x00000001U
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U2_S 4
|
|
/** PCNT_CNT_THR_H_LIM_LAT_U2 : RO; bitpos: [5]; default: 0;
|
|
* The latched value of high limit event of PCNT_U2 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thr_h_lim and high limit event is
|
|
* valid. 0: others
|
|
*/
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U2 (BIT(5))
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U2_M (PCNT_CNT_THR_H_LIM_LAT_U2_V << PCNT_CNT_THR_H_LIM_LAT_U2_S)
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U2_V 0x00000001U
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U2_S 5
|
|
/** PCNT_CNT_THR_ZERO_LAT_U2 : RO; bitpos: [6]; default: 0;
|
|
* The latched value of zero threshold event of PCNT_U2 when threshold event interrupt
|
|
* is valid. 1: the current pulse counter equals to 0 and zero threshold event is
|
|
* valid. 0: others
|
|
*/
|
|
#define PCNT_CNT_THR_ZERO_LAT_U2 (BIT(6))
|
|
#define PCNT_CNT_THR_ZERO_LAT_U2_M (PCNT_CNT_THR_ZERO_LAT_U2_V << PCNT_CNT_THR_ZERO_LAT_U2_S)
|
|
#define PCNT_CNT_THR_ZERO_LAT_U2_V 0x00000001U
|
|
#define PCNT_CNT_THR_ZERO_LAT_U2_S 6
|
|
|
|
/** PCNT_U3_STATUS_REG register
|
|
* PNCT UNIT3 status register
|
|
*/
|
|
#define PCNT_U3_STATUS_REG (DR_REG_PCNT_BASE + 0x5c)
|
|
/** PCNT_CNT_THR_ZERO_MODE_U3 : RO; bitpos: [1:0]; default: 0;
|
|
* The pulse counter status of PCNT_U3 corresponding to 0. 0: pulse counter decreases
|
|
* from positive to 0. 1: pulse counter increases from negative to 0. 2: pulse counter
|
|
* is negative. 3: pulse counter is positive.
|
|
*/
|
|
#define PCNT_CNT_THR_ZERO_MODE_U3 0x00000003U
|
|
#define PCNT_CNT_THR_ZERO_MODE_U3_M (PCNT_CNT_THR_ZERO_MODE_U3_V << PCNT_CNT_THR_ZERO_MODE_U3_S)
|
|
#define PCNT_CNT_THR_ZERO_MODE_U3_V 0x00000003U
|
|
#define PCNT_CNT_THR_ZERO_MODE_U3_S 0
|
|
/** PCNT_CNT_THR_THRES1_LAT_U3 : RO; bitpos: [2]; default: 0;
|
|
* The latched value of thres1 event of PCNT_U3 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thres1 and thres1 event is valid. 0:
|
|
* others
|
|
*/
|
|
#define PCNT_CNT_THR_THRES1_LAT_U3 (BIT(2))
|
|
#define PCNT_CNT_THR_THRES1_LAT_U3_M (PCNT_CNT_THR_THRES1_LAT_U3_V << PCNT_CNT_THR_THRES1_LAT_U3_S)
|
|
#define PCNT_CNT_THR_THRES1_LAT_U3_V 0x00000001U
|
|
#define PCNT_CNT_THR_THRES1_LAT_U3_S 2
|
|
/** PCNT_CNT_THR_THRES0_LAT_U3 : RO; bitpos: [3]; default: 0;
|
|
* The latched value of thres0 event of PCNT_U3 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thres0 and thres0 event is valid. 0:
|
|
* others
|
|
*/
|
|
#define PCNT_CNT_THR_THRES0_LAT_U3 (BIT(3))
|
|
#define PCNT_CNT_THR_THRES0_LAT_U3_M (PCNT_CNT_THR_THRES0_LAT_U3_V << PCNT_CNT_THR_THRES0_LAT_U3_S)
|
|
#define PCNT_CNT_THR_THRES0_LAT_U3_V 0x00000001U
|
|
#define PCNT_CNT_THR_THRES0_LAT_U3_S 3
|
|
/** PCNT_CNT_THR_L_LIM_LAT_U3 : RO; bitpos: [4]; default: 0;
|
|
* The latched value of low limit event of PCNT_U3 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thr_l_lim and low limit event is
|
|
* valid. 0: others
|
|
*/
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U3 (BIT(4))
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U3_M (PCNT_CNT_THR_L_LIM_LAT_U3_V << PCNT_CNT_THR_L_LIM_LAT_U3_S)
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U3_V 0x00000001U
|
|
#define PCNT_CNT_THR_L_LIM_LAT_U3_S 4
|
|
/** PCNT_CNT_THR_H_LIM_LAT_U3 : RO; bitpos: [5]; default: 0;
|
|
* The latched value of high limit event of PCNT_U3 when threshold event interrupt is
|
|
* valid. 1: the current pulse counter equals to thr_h_lim and high limit event is
|
|
* valid. 0: others
|
|
*/
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U3 (BIT(5))
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U3_M (PCNT_CNT_THR_H_LIM_LAT_U3_V << PCNT_CNT_THR_H_LIM_LAT_U3_S)
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U3_V 0x00000001U
|
|
#define PCNT_CNT_THR_H_LIM_LAT_U3_S 5
|
|
/** PCNT_CNT_THR_ZERO_LAT_U3 : RO; bitpos: [6]; default: 0;
|
|
* The latched value of zero threshold event of PCNT_U3 when threshold event interrupt
|
|
* is valid. 1: the current pulse counter equals to 0 and zero threshold event is
|
|
* valid. 0: others
|
|
*/
|
|
#define PCNT_CNT_THR_ZERO_LAT_U3 (BIT(6))
|
|
#define PCNT_CNT_THR_ZERO_LAT_U3_M (PCNT_CNT_THR_ZERO_LAT_U3_V << PCNT_CNT_THR_ZERO_LAT_U3_S)
|
|
#define PCNT_CNT_THR_ZERO_LAT_U3_V 0x00000001U
|
|
#define PCNT_CNT_THR_ZERO_LAT_U3_S 6
|
|
|
|
/** PCNT_CTRL_REG register
|
|
* Control register for all counters
|
|
*/
|
|
#define PCNT_CTRL_REG (DR_REG_PCNT_BASE + 0x60)
|
|
/** PCNT_PULSE_CNT_RST_U0 : R/W; bitpos: [0]; default: 1;
|
|
* Set this bit to clear unit 0's counter.
|
|
*/
|
|
#define PCNT_PULSE_CNT_RST_U0 (BIT(0))
|
|
#define PCNT_PULSE_CNT_RST_U0_M (PCNT_PULSE_CNT_RST_U0_V << PCNT_PULSE_CNT_RST_U0_S)
|
|
#define PCNT_PULSE_CNT_RST_U0_V 0x00000001U
|
|
#define PCNT_PULSE_CNT_RST_U0_S 0
|
|
/** PCNT_CNT_PAUSE_U0 : R/W; bitpos: [1]; default: 0;
|
|
* Set this bit to freeze unit 0's counter.
|
|
*/
|
|
#define PCNT_CNT_PAUSE_U0 (BIT(1))
|
|
#define PCNT_CNT_PAUSE_U0_M (PCNT_CNT_PAUSE_U0_V << PCNT_CNT_PAUSE_U0_S)
|
|
#define PCNT_CNT_PAUSE_U0_V 0x00000001U
|
|
#define PCNT_CNT_PAUSE_U0_S 1
|
|
/** PCNT_PULSE_CNT_RST_U1 : R/W; bitpos: [2]; default: 1;
|
|
* Set this bit to clear unit 1's counter.
|
|
*/
|
|
#define PCNT_PULSE_CNT_RST_U1 (BIT(2))
|
|
#define PCNT_PULSE_CNT_RST_U1_M (PCNT_PULSE_CNT_RST_U1_V << PCNT_PULSE_CNT_RST_U1_S)
|
|
#define PCNT_PULSE_CNT_RST_U1_V 0x00000001U
|
|
#define PCNT_PULSE_CNT_RST_U1_S 2
|
|
/** PCNT_CNT_PAUSE_U1 : R/W; bitpos: [3]; default: 0;
|
|
* Set this bit to freeze unit 1's counter.
|
|
*/
|
|
#define PCNT_CNT_PAUSE_U1 (BIT(3))
|
|
#define PCNT_CNT_PAUSE_U1_M (PCNT_CNT_PAUSE_U1_V << PCNT_CNT_PAUSE_U1_S)
|
|
#define PCNT_CNT_PAUSE_U1_V 0x00000001U
|
|
#define PCNT_CNT_PAUSE_U1_S 3
|
|
/** PCNT_PULSE_CNT_RST_U2 : R/W; bitpos: [4]; default: 1;
|
|
* Set this bit to clear unit 2's counter.
|
|
*/
|
|
#define PCNT_PULSE_CNT_RST_U2 (BIT(4))
|
|
#define PCNT_PULSE_CNT_RST_U2_M (PCNT_PULSE_CNT_RST_U2_V << PCNT_PULSE_CNT_RST_U2_S)
|
|
#define PCNT_PULSE_CNT_RST_U2_V 0x00000001U
|
|
#define PCNT_PULSE_CNT_RST_U2_S 4
|
|
/** PCNT_CNT_PAUSE_U2 : R/W; bitpos: [5]; default: 0;
|
|
* Set this bit to freeze unit 2's counter.
|
|
*/
|
|
#define PCNT_CNT_PAUSE_U2 (BIT(5))
|
|
#define PCNT_CNT_PAUSE_U2_M (PCNT_CNT_PAUSE_U2_V << PCNT_CNT_PAUSE_U2_S)
|
|
#define PCNT_CNT_PAUSE_U2_V 0x00000001U
|
|
#define PCNT_CNT_PAUSE_U2_S 5
|
|
/** PCNT_PULSE_CNT_RST_U3 : R/W; bitpos: [6]; default: 1;
|
|
* Set this bit to clear unit 3's counter.
|
|
*/
|
|
#define PCNT_PULSE_CNT_RST_U3 (BIT(6))
|
|
#define PCNT_PULSE_CNT_RST_U3_M (PCNT_PULSE_CNT_RST_U3_V << PCNT_PULSE_CNT_RST_U3_S)
|
|
#define PCNT_PULSE_CNT_RST_U3_V 0x00000001U
|
|
#define PCNT_PULSE_CNT_RST_U3_S 6
|
|
/** PCNT_CNT_PAUSE_U3 : R/W; bitpos: [7]; default: 0;
|
|
* Set this bit to freeze unit 3's counter.
|
|
*/
|
|
#define PCNT_CNT_PAUSE_U3 (BIT(7))
|
|
#define PCNT_CNT_PAUSE_U3_M (PCNT_CNT_PAUSE_U3_V << PCNT_CNT_PAUSE_U3_S)
|
|
#define PCNT_CNT_PAUSE_U3_V 0x00000001U
|
|
#define PCNT_CNT_PAUSE_U3_S 7
|
|
/** PCNT_DELTA_CHANGE_EN_U0 : R/W; bitpos: [8]; default: 0;
|
|
* Configures this bit to enable unit 0's step comparator.
|
|
*/
|
|
#define PCNT_DELTA_CHANGE_EN_U0 (BIT(8))
|
|
#define PCNT_DELTA_CHANGE_EN_U0_M (PCNT_DELTA_CHANGE_EN_U0_V << PCNT_DELTA_CHANGE_EN_U0_S)
|
|
#define PCNT_DELTA_CHANGE_EN_U0_V 0x00000001U
|
|
#define PCNT_DELTA_CHANGE_EN_U0_S 8
|
|
/** PCNT_DELTA_CHANGE_EN_U1 : R/W; bitpos: [9]; default: 0;
|
|
* Configures this bit to enable unit 1's step comparator.
|
|
*/
|
|
#define PCNT_DELTA_CHANGE_EN_U1 (BIT(9))
|
|
#define PCNT_DELTA_CHANGE_EN_U1_M (PCNT_DELTA_CHANGE_EN_U1_V << PCNT_DELTA_CHANGE_EN_U1_S)
|
|
#define PCNT_DELTA_CHANGE_EN_U1_V 0x00000001U
|
|
#define PCNT_DELTA_CHANGE_EN_U1_S 9
|
|
/** PCNT_DELTA_CHANGE_EN_U2 : R/W; bitpos: [10]; default: 0;
|
|
* Configures this bit to enable unit 2's step comparator.
|
|
*/
|
|
#define PCNT_DELTA_CHANGE_EN_U2 (BIT(10))
|
|
#define PCNT_DELTA_CHANGE_EN_U2_M (PCNT_DELTA_CHANGE_EN_U2_V << PCNT_DELTA_CHANGE_EN_U2_S)
|
|
#define PCNT_DELTA_CHANGE_EN_U2_V 0x00000001U
|
|
#define PCNT_DELTA_CHANGE_EN_U2_S 10
|
|
/** PCNT_DELTA_CHANGE_EN_U3 : R/W; bitpos: [11]; default: 0;
|
|
* Configures this bit to enable unit 3's step comparator.
|
|
*/
|
|
#define PCNT_DELTA_CHANGE_EN_U3 (BIT(11))
|
|
#define PCNT_DELTA_CHANGE_EN_U3_M (PCNT_DELTA_CHANGE_EN_U3_V << PCNT_DELTA_CHANGE_EN_U3_S)
|
|
#define PCNT_DELTA_CHANGE_EN_U3_V 0x00000001U
|
|
#define PCNT_DELTA_CHANGE_EN_U3_S 11
|
|
/** PCNT_CLK_EN : R/W; bitpos: [16]; default: 0;
|
|
* The registers clock gate enable signal of PCNT module. 1: the registers can be read
|
|
* and written by application. 0: the registers can not be read or written by
|
|
* application
|
|
*/
|
|
#define PCNT_CLK_EN (BIT(16))
|
|
#define PCNT_CLK_EN_M (PCNT_CLK_EN_V << PCNT_CLK_EN_S)
|
|
#define PCNT_CLK_EN_V 0x00000001U
|
|
#define PCNT_CLK_EN_S 16
|
|
|
|
/** PCNT_U3_CHANGE_CONF_REG register
|
|
* Configuration register for unit $n's step value.
|
|
*/
|
|
#define PCNT_U3_CHANGE_CONF_REG (DR_REG_PCNT_BASE + 0x64)
|
|
/** PCNT_CNT_STEP_U3 : R/W; bitpos: [15:0]; default: 0;
|
|
* Configures the step value for unit 3.
|
|
*/
|
|
#define PCNT_CNT_STEP_U3 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_U3_M (PCNT_CNT_STEP_U3_V << PCNT_CNT_STEP_U3_S)
|
|
#define PCNT_CNT_STEP_U3_V 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_U3_S 0
|
|
/** PCNT_CNT_STEP_LIM_U3 : R/W; bitpos: [31:16]; default: 0;
|
|
* Configures the step limit value for unit 3.
|
|
*/
|
|
#define PCNT_CNT_STEP_LIM_U3 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_LIM_U3_M (PCNT_CNT_STEP_LIM_U3_V << PCNT_CNT_STEP_LIM_U3_S)
|
|
#define PCNT_CNT_STEP_LIM_U3_V 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_LIM_U3_S 16
|
|
|
|
/** PCNT_U2_CHANGE_CONF_REG register
|
|
* Configuration register for unit $n's step value.
|
|
*/
|
|
#define PCNT_U2_CHANGE_CONF_REG (DR_REG_PCNT_BASE + 0x68)
|
|
/** PCNT_CNT_STEP_U2 : R/W; bitpos: [15:0]; default: 0;
|
|
* Configures the step value for unit 2.
|
|
*/
|
|
#define PCNT_CNT_STEP_U2 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_U2_M (PCNT_CNT_STEP_U2_V << PCNT_CNT_STEP_U2_S)
|
|
#define PCNT_CNT_STEP_U2_V 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_U2_S 0
|
|
/** PCNT_CNT_STEP_LIM_U2 : R/W; bitpos: [31:16]; default: 0;
|
|
* Configures the step limit value for unit 2.
|
|
*/
|
|
#define PCNT_CNT_STEP_LIM_U2 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_LIM_U2_M (PCNT_CNT_STEP_LIM_U2_V << PCNT_CNT_STEP_LIM_U2_S)
|
|
#define PCNT_CNT_STEP_LIM_U2_V 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_LIM_U2_S 16
|
|
|
|
/** PCNT_U1_CHANGE_CONF_REG register
|
|
* Configuration register for unit $n's step value.
|
|
*/
|
|
#define PCNT_U1_CHANGE_CONF_REG (DR_REG_PCNT_BASE + 0x6c)
|
|
/** PCNT_CNT_STEP_U1 : R/W; bitpos: [15:0]; default: 0;
|
|
* Configures the step value for unit 1.
|
|
*/
|
|
#define PCNT_CNT_STEP_U1 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_U1_M (PCNT_CNT_STEP_U1_V << PCNT_CNT_STEP_U1_S)
|
|
#define PCNT_CNT_STEP_U1_V 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_U1_S 0
|
|
/** PCNT_CNT_STEP_LIM_U1 : R/W; bitpos: [31:16]; default: 0;
|
|
* Configures the step limit value for unit 1.
|
|
*/
|
|
#define PCNT_CNT_STEP_LIM_U1 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_LIM_U1_M (PCNT_CNT_STEP_LIM_U1_V << PCNT_CNT_STEP_LIM_U1_S)
|
|
#define PCNT_CNT_STEP_LIM_U1_V 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_LIM_U1_S 16
|
|
|
|
/** PCNT_U0_CHANGE_CONF_REG register
|
|
* Configuration register for unit $n's step value.
|
|
*/
|
|
#define PCNT_U0_CHANGE_CONF_REG (DR_REG_PCNT_BASE + 0x70)
|
|
/** PCNT_CNT_STEP_U0 : R/W; bitpos: [15:0]; default: 0;
|
|
* Configures the step value for unit 0.
|
|
*/
|
|
#define PCNT_CNT_STEP_U0 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_U0_M (PCNT_CNT_STEP_U0_V << PCNT_CNT_STEP_U0_S)
|
|
#define PCNT_CNT_STEP_U0_V 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_U0_S 0
|
|
/** PCNT_CNT_STEP_LIM_U0 : R/W; bitpos: [31:16]; default: 0;
|
|
* Configures the step limit value for unit 0.
|
|
*/
|
|
#define PCNT_CNT_STEP_LIM_U0 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_LIM_U0_M (PCNT_CNT_STEP_LIM_U0_V << PCNT_CNT_STEP_LIM_U0_S)
|
|
#define PCNT_CNT_STEP_LIM_U0_V 0x0000FFFFU
|
|
#define PCNT_CNT_STEP_LIM_U0_S 16
|
|
|
|
/** PCNT_DATE_REG register
|
|
* PCNT version control register
|
|
*/
|
|
#define PCNT_DATE_REG (DR_REG_PCNT_BASE + 0xfc)
|
|
/** PCNT_DATE : R/W; bitpos: [31:0]; default: 571021568;
|
|
* This is the PCNT version control register.
|
|
*/
|
|
#define PCNT_DATE 0xFFFFFFFFU
|
|
#define PCNT_DATE_M (PCNT_DATE_V << PCNT_DATE_S)
|
|
#define PCNT_DATE_V 0xFFFFFFFFU
|
|
#define PCNT_DATE_S 0
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|