alex/esp-idf
alex/esp-idf
1
0
Fork 0
mirror of https://github.com/espressif/esp-idf.git synced 2024-10-05 20:47:46 -04:00
Code Issues Actions 2 Packages Projects Releases Wiki Activity
07245bf43a
esp-idf/examples/zigbee/esp_zigbee_gateway
History
zhangyanjiao 07245bf43a fix(wifi/mesh): fix the IE crypto disable error and update doc
2023-11-16 11:03:59 +08:00
..
main fix(wifi/mesh): fix the IE crypto disable error and update doc 2023-11-16 11:03:59 +08:00
CMakeLists.txt feat(examples): add local components via idf_component.yml 2023-09-19 10:38:24 +02:00
partitions.csv zigbee: zigbee gateway support for single chip esp32-c6 solution 2023-04-07 11:24:19 +08:00
README.md docs: update the readme for Thread/Zigbee examples 2023-04-07 12:22:52 +08:00
sdkconfig.defaults zigbee: zigbee gateway support for single chip esp32-c6 solution 2023-04-07 11:24:19 +08:00

README.md

Supported Targets ESP32 ESP32-C3 ESP32-C6 ESP32-S2 ESP32-S3

Gateway Example

This example demonstrates how to build a Zigbee Gateway device.

The ESP Zigbee SDK provides more examples and tools for productization:

Hardware Required

By default, two SoCs are required to run this example:

  • An ESP32 series Wi-Fi SoC (ESP32, ESP32-C, ESP32-S, etc) loaded with this esp_zigbee_gateway example.
  • An ESP32-H2 802.15.4 SoC loaded with esp_zigbee_rcp example

Connect the two SoCs via UART, below is an example setup with ESP32-DevKitC and ESP32-H2-DevKitC: Zigbee_gateway

ESP32 pin ESP32-H2 pin
GND G
GPIO4 (RX) TX
GPIO5 (TX) RX
  • TX, RX pin can be also configured by user in esp_zigbee_gateway.h

The example could also run on a single SoC which supports both Wi-Fi and Zigbee (e.g., ESP32-C6), but since there is only one RF path in ESP32-C6, which means Wi-Fi and Zigbee can't receive simultaneously, it has a significant impact on performance. Hence the two SoCs solution is recommended.

Configure the project

Before project configuration and build, make sure to set the correct chip target using idf.py set-target <chip_name>.

In order to run the example on single SoC which supports both Wi-Fi and Thread, the option CONFIG_ESP_COEX_SW_COEXIST_ENABLE and option CONFIG_ZB_RADIO_NATIVE should be enabled. The two options are enabled by default for ESP32-C6 target.

Erase the NVRAM

Before flash it to the board, it is recommended to erase NVRAM if user doesn't want to keep the previous examples or other projects stored info using idf.py -p PORT erase-flash

Build and Flash

Build the project, flash it to the board, and start the monitor tool to view the serial output by running idf.py -p PORT flash monitor

(To exit the serial monitor, type Ctrl-].)

Example Output

As you run the example, you will see the following log:

esp_zigbee_gateway:

I (660) ESP_ZB_GATEWAY: status: -1
I (670) ESP_ZB_GATEWAY: Zigbee stack initialized
I (680) ESP_ZB_GATEWAY: Zigbee rcp device booted
I (1280) ESP_ZB_GATEWAY: Start network formation
I (3060) ESP_ZB_GATEWAY: Formed network successfully (ieee extended address: f9:54:2d:01:a0:03:f7:84, PAN ID: 0x8651)
I (4060) ESP_ZB_GATEWAY: status: 0
I (4400) ESP_ZB_GATEWAY: Network steering started

Gateway Functions

  • After Zigbee gateway starts up, it will read MAC ieee address and Zigbee stack version number from the Zigbee rcp and start working together with Zigbee rcp via UART communication to form a Zigbee network
  • More Gateway functionalities supporting Wi-Fi interaction will come later

Troubleshooting

For any technical queries, please open an issue on GitHub. We will get back to you soon